Kicker 47KSMT25 Manuel utilisateur

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 1of 8

PARTS LIST

ITEM NO.

DESCRIPTION

QTY.

47KSMT25 POD ASSEMBLY WITH NUT AND WASHER

BUTT CONNECTOR

47KSMT25 CROSSOVER

CAPACITOR

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 2of 8

The Kicker KSMT25 pod provides a mid and tweeter with optimized adjustability. The pod can

be mounted to almost any surface where a hole can be drilled. Not only does the entire pod

assembly pivot, lean, and rotate on the ball and socket mounting stud - the tweeter also has

approximately 260 degrees of planetary rotation around the mid to provide desired orientation.

This document demonstrates adjusting, mounting, and wiring of the KSMT25 pod assembly for

the following Kicker models:

•47KSMT2504

PARTS IDENTIFICATION

Below is a list describing part names used in these instructions.

(1) KSMT25 pod assembly

(2) Tweeter

(3) Mid

(4) Mounting Stud

(5) Decorative Plug

(6) Washer

(7) Wing Nut

(1)

(2)

(3)

(4)

(5)

(6)

(7)

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 3of 8

READ AND UNDERSTAND ALL OF THESE INSTRUTIONS BEFORE

INSTALLATION!

ADJUSTABILITY OF THE KSMT25 POD

The KSMT25 tweeter pod assembly pivots and rotates on its mounting stud. This can be

accomplished any time before or after installation.

1. To adjust the rotation of the tweeter around the mid, remove the decorative plug at the

back of the pod assembly. Using a 2.5mm allen wrench, loosen (do not remove) the bolt

retaining the tweeter to the mid.

2. Rotate the tweeter to the desired location and retighten the bolt. Replace the decorative

plug.

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 4of 8

TIGHTENING THE BALL AND SOCKET MOUNT

If the pod assembly will not remain stationary on the stud, the ball and socket clamp can

be tightened to prevent pod movement.

1. Remove the nut and washer from the stud.

2. Using a 2mm allen wrench, tighten the three bolts on the bottom of the pod to increase

clamping force on the ball and socket.

MOUNTING THE KSMT25 TWEETER POD

Choose a mounting surface that can be accessed from both side as a wing nut must be

installed on the mounting stud to retain the pod in its location.

1. Drill a 9/16”hole in the desired mounting location.

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 5of 8

2. Place the washer on the mounting stud then insert the mounting stud into the drilled hole

Secure the pod assembly to the mounting surface with the wing nut.

CONNECTING THE CROSSOVERS TO THE PODS

DANGER! Electrical hazard. Burns, electric shock, or damage to equipment

may occur during connection of electrical wires. Always disconnect the vehicle’s

power source before making wire connections.

Kicker supplies crossovers with KSMT25 to optimize the sound of the pod’s speakers.

The KSMT25 crossover is terminated so that it will only connect to the KSMT25 assembly.

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 6of 8

NOTE: The KSMT25 crossover is labeled with the part number 47KSMT25-XO.

1. Connect the crossover terminals and receptacles to their respective mating connector on

the KSMT25 pod assembly. The terminals on the 47KSMT25 crossover are all different

sizes and types to prevent incorrect connection. Also, the crossover wire colors match the

pod assembly wire colors.

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 7of 8

2. Slide the clear cover over the terminals to prevent a short circuit.

3. Connect the crossover input to the outputs of the head unit or amplifier using the supplied

butt connectors. The positive lead is the wire with gray insulation labeled with a “plus”

symbol. The negative lead has gray insulation with a black stripe on it.

EOP2021-CS4

7/6/2021

REV-A.3

47KSMT25 Installation Guide

Page 8of 8

CONNECTING CAPACITORS TO CROSSOVERS

When using an active crossover DO NOT use the supplied capacitors. Instead tune the

amplifier channel powering the KSMT25 to play above 400 hertz at 12db per octave slope or

greater.

If an active crossover is not used, solder the supplied capacitors to the positive inputs of

the 47KSMT25 crossovers. Cover solder joints with heat shrink.

SUPPLIED CAPACITOR

Table des matières

Autres manuels Kicker Intervenants

Kicker

Kicker KM6LC Manuel utilisateur

Kicker

Kicker DSC4 Manuel utilisateur

Kicker

Kicker PSC65 Manuel utilisateur

Kicker

Kicker KM604 Manuel utilisateur

Kicker

Kicker DS350 Manuel utilisateur

Kicker

Kicker YJ-SPKUP Manuel utilisateur

Kicker

Kicker KSS50 Manuel utilisateur

Kicker

Kicker KSS50 Manuel utilisateur

Kicker

Kicker DS35 Manuel utilisateur

Kicker

Kicker 49ST4TW Manuel utilisateur

Kicker

Kicker PSC57 Manuel utilisateur

Kicker

Kicker 45KM604 Manuel utilisateur

Kicker

Kicker SS Series Manuel utilisateur

Kicker

Kicker KS Series Manuel utilisateur

Kicker

Kicker PS5250 Manuel utilisateur

Kicker

Kicker KM10 Manuel utilisateur

Kicker

Kicker Street Series Manuel utilisateur

Kicker

Kicker 45KM44 Manuel utilisateur

Kicker

Kicker KMFC8 Manuel utilisateur

Kicker

Kicker K35 Manuel utilisateur

Kicker

Kicker BT Cans Manuel utilisateur

Kicker

Kicker KM620 Manuel utilisateur

Kicker

Kicker SS Series Manuel utilisateur

Kicker

Kicker 41KM604W Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur