Kicker FKAVV09 Manuel utilisateur

KICKER AMP & SPEAKER

INSTALLATION GUIDE

FOR USE WITH KAWASAKI VAQUERO

> Step-by-step Installation Guide

> 5 1/4” Kicker Speakers Pair

> Kicker Amp 100W/50W

> Stainless Steel Mounting Bracket

> Custom Wiring Harness

> All Necessary Hardware

- 8 - 32 x 1/2” Button Head Bolts

- 8 - 32 Nylock Nuts

> Black Heat Shrink

> Black Cable Tie

INCLUDED IN THIS FIT KIT:

KLOCK WERKS | VAQUERO KICKER INSTALLATION 2

GETTING STARTED | *Please reference model appropriate service manual for procedures and torque speciﬁcations.

1. Protect painted surfaces with a soft cloth.

2. Remove the seat.

3. Remove plastic battery cover.

4. Disconnect battery.

AMP INSTALLATION

5. Follow the proper procedure to remove the outer fairing.

6. Install ampliﬁer onto bracket Slide the ampliﬁer into the left side of the bracket and use supplied hardware

to bolt the amp to the bracket. (Pic 1)

7. Remove the two fasteners holding the radio chassis to the inner fairing bracket

8. Set the ampliﬁer assembly on top of the inner fairing bracket and use the hardware removed in step 7

to fasten it back onto the inner fairing bracket. (Pic 2)

HARNESS INSTALLATION

9. Follow the proper procedure to remove the fuel tank.

10. Plug harness into the ampliﬁer.

11. Route the right side speaker wires behind the ampliﬁer toward the right side speaker pod.

12. Route the left side wires behind the fairing support toward the left side speaker pod. (pic 3)

13. The blue wire is to be installed in the accessory power source on the left side of the fairing.

It is a tan wire with a double barrel terminal. (pic 4)

14. Route the power leads along the main harness. (pic 5):

1. Along the left side of the frame neck.

2. Under the black wire retainer on the neck.

3. Under the front fuel tank bumper.

4. Underneath the anodized wire retainer. (You will have to loosen the bracket)

5. Under the rear fuel tank bumper.

6. Follow the harness down the right side of the frame and under the seat.

15. The blue lead under the seat would be used if installing a second ampliﬁer, but whether used or not,

cover with supplied heat shrink to reduce the risk of a short.

1 2

3 4 5

KLOCK WERKS | VAQUERO KICKER INSTALLATION 3

SPEAKER INSTALLATION

16. Remove the four Phillips head screws, pull the speaker out of its housing and unplug the stock speaker wires.

17. Take the left side speaker wires and insert them through the hole in the bottom of the speaker pod. (pic 6)

18. Plug the male ends from the ampliﬁer harness into the stock speaker terminals. (pic 7)

19. Plug the female ends from the ampliﬁer harness onto the Kicker speaker and refasten it to the housing with

the Phillips head screws removed in step 16. (pic 8)

20. Repeat for the right side speaker.

21. Thread the positive power lead into the protective red cap and fasten to the battery. (pic 9)

22. Connect the negative power lead and check system operation.

23. Be sure to check that none of the wires will be in a bind when the steering head is turned fully to the right

or the left.

Note: At this time, it is highly recommended to follow the guidelines in your Kicker PX 100.2 owner’s manual

to set up the ampliﬁer. Klock Werks recommends that the dip switches be set up as follows:

AUTO TURN-ON - 12V

INPUT LEVEL - HI

HI-PASS – OFF

INPUT GAIN CONTROL – Follow the instructions in your Kicker PX 100.2 owner’s manual Pg. 4

24. Disconnect the negative battery terminal and carefully reassemble motorcycle.

25. Connect negative battery terminal, install the battery cover and seat and enjoy your Kicker audio system!

678

Table des matières

Autres manuels Kicker Intervenants

Kicker

Kicker KSS50 Manuel utilisateur

Kicker

Kicker 19418149 Manuel utilisateur

Kicker

Kicker 47KSMT25 Manuel utilisateur

Kicker

Kicker KM44CW Manuel utilisateur

Kicker

Kicker 41KPWB Manuel utilisateur

Kicker

Kicker KM6LC Manuel utilisateur

Kicker

Kicker KM4 Manuel utilisateur

Kicker

Kicker I4.2 Manuel utilisateur

Kicker

Kicker SSMB6 Manuel utilisateur

Kicker

Kicker KM604 Manuel utilisateur

Kicker

Kicker K35 Manuel utilisateur

Kicker

Kicker SSMB Series Manuel utilisateur

Kicker

Kicker Separates Series Manuel utilisateur

Kicker

Kicker DS350 Manuel utilisateur

Kicker

Kicker KM6000 Manuel utilisateur

Kicker

Kicker DSC4 Manuel utilisateur

Kicker

Kicker CSS65 Manuel utilisateur

Kicker

Kicker 48KSS269 Manuel utilisateur

Kicker

Kicker KM6200 Manuel utilisateur

Kicker

Kicker 48BTCAN65 Manuel utilisateur

Kicker

Kicker KMTC9 Manuel utilisateur

Kicker

Kicker PSC65 Manuel utilisateur

Kicker

Kicker DS35 Manuel utilisateur

Kicker

Kicker PSM3 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur