Keysight Technologies N9041B Manuel d'installation et d'exploitation

Keysight N9041B

Signal Analyzer

Option EDC

External Digitizer Control

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9041-90008

Edition

Edition 1, April 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9041-90008 3

Option EDC Upgrade

Products Affected: N9041B UXA Signal Analyzer

Serial Numbers: All

Options Required: N9041B-CRW, IF Output, Ultra-Wide Bandwidth

To Be Performed By: ( ) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time: 0.5 Hours

4Installation Note N9041-90008

Option EDC Upgrade

Introduction

Option EDC, External Digitizer Control allows the rear panel Ext IF Output (Ultra-wide bandwidth IF

Output, Option CRW) to be used with an oscilloscope and Keysight VSA measurement software.

This installation note provides instructions for licensing Option EDC on the N9041B. No instructions

are provided on the configuration and use of the oscilloscope and VSA software.

Requirements

— Instrument software revision must be A.21.00 or later

— Option CRW, Ultra-Wide Bandwidth IF Output, must be installed (licensed). All N9041B

instruments ship with the Ext IF Out connector on the rear panel, but Option CRW must be

licensed before the Ext IF Out connector will function.

Contents

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

1. The latest revision of the X-Series signal analyzer software may be

downloaded from:

http://www.keysight.com/find/Xseries_software

2. This option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

Quantity Description Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9041-90008 5

Option EDC Upgrade

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show System.

Make note of the following information from the Show System screen:

Product Number _______________

Instrument S/W Revision _______________

3. Check for the presence of the options listed below in the Show System screen. Put a check

mark after each option listed below that appears in the show System menu.

N9041B-CRW _______________

4. Refer to the data in step 2 above. Verify that the Product Number in step 2 is appropriate for

the upgrade being installed:

If the Product Number in step 2 is not appropriate for the Option EDC upgrade, do not proceed

with the installation.

5. Refer to the data in step 2 above. If the instrument software is earlier than A.21.00, you must

upgrade to version A.21.00 or later. Keysight recommends that you update to the latest

instrument software version to ensure that you have the latest defect fixes. To check the latest

instrument software version, visit the following website:

http://www.keysight.com/find/N9041B_software

6. Refer to the data in step 3 above.

Verify that N9041B-CRW is checked (currently installed).

If N9041B-CRW is not installed, do not proceed with the installation of this kit. Option CRW, IF

Output, Ultra-Wide Bandwidth, is required to enable the rear panel Ext IF Out port.

For information on how to order Option CRW refer to the N9041B upgrade page at:

http://www.keysight.com\find\N9041B_upgrades

Kit to be Installed Product Number (Step 2)

N9041BU-EDC N9041B

6Installation Note N9041-90008

Option EDC Upgrade

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message as shown in Figure 2.

Figure 2 Successful License Installation

Installation Note N9041-90008 7

Option EDC Upgrade

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option, N9041B-EDC, External Digitizer Control, appears on the

list.

4. Verify that Option N9041B-CRW also appears. this assures Option CRW is installed since

Option EDC requires Option CRW.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

Edition 1, April 2018

N9041-90008

www.keysight.com

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies U2000 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies 34136A Manuel utilisateur

Keysight Technologies

Keysight Technologies M9393A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies M9710A Guide rapide

Keysight Technologies

Keysight Technologies B2900A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies E4981A Manuel utilisateur

Keysight Technologies

Keysight Technologies U8903B Manuel utilisateur

Keysight Technologies

Keysight Technologies M9393A Mode d'emploi

Keysight Technologies

Keysight Technologies ENA Series Guide de démarrage rapide

Keysight Technologies

Keysight Technologies 8990B Manuel utilisateur

Keysight Technologies

Keysight Technologies B1500A Manuel utilisateur

Keysight Technologies

Keysight Technologies X-Series Guide de démarrage rapide

Keysight Technologies

Keysight Technologies P5000A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies Agilent Technologies PXI Express M9202A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies PXA N9030A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N5290A Manuel utilisateur

Keysight Technologies

Keysight Technologies N7020A Manuel utilisateur

Keysight Technologies

Keysight Technologies N9020B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies 85059B Manuel de service

Keysight Technologies

Keysight Technologies UXA N9040B Manuel utilisateur

Keysight Technologies

Keysight Technologies U1731C Manuel utilisateur

Keysight Technologies

Keysight Technologies MY53280000 Guide de démarrage rapide

Keysight Technologies

Keysight Technologies P5000A Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur