Keysight Technologies N9020B Manuel d'installation et d'exploitation
Option BU1, 40 MHz to 85 MHz Analysis Bandwidth Upgrade
Option BU2, 40 MHz to 125 MHz Analysis Bandwidth Upgrade
Option BU3, 40 MHz to 160 MHz Analysis Bandwidth Upgrade
Keysight Technologies
N9020B MXA Signal Analyzer
Installation Note
Notices
© Copyright 2016 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9020-90254
Edition
Edition 1, May 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9020-90254 3
Option BU1/BU2/BU3, 40 MHz to 85/125/160 MHz Analysis Bandwidth Upgrade
Option BU1/BU2/BU3, 40 MHz to 85/125/160 MHz Analysis
Bandwidth Upgrade
Introduction
This installation note explains how to install the hardware and provides guidelines for adjustment
and verification for the following upgrade kits for MXA N9020B signal analyzers:
— Option BU1, Analysis Bandwidth Upgrade, 40 MHz to 85 MHz, Hardware and License
— Option BU2, Analysis Bandwidth Upgrade, 40 MHz to 125 MHz, Hardware and License
— Option BU3, Analysis Bandwidth Upgrade, 40 MHz to 160 MHz, Hardware and License
Installing this kit requires that the analyzer already have hardware and licenses installed to provide
analysis bandwidths up to 40 MHz. Other upgrade kits are available to upgrade analyzers that only
have analysis bandwidths up to 25 MHz.
Refer to http://www.keysight.com/find/mxa_upgrades for information of available upgrades.
Products Affected: N9020B MXA Signal Analyzer
Serial Numbers:
Options: B40, MPB (for frequency range options 508, 513, or 526)
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
1.5 Hours
1.5 Hours
3.5 Hours
4Installation Note N9020-90254
Option BU1/BU2/BU3, 40 MHz to 85/125/160 MHz Analysis Bandwidth Upgrade
Software and test equipment is required for making adjustments and for performance verification
testing.
Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
The instrument must be readjusted and the performance tested to assure the instrument meets
specifications following the hardware installation. The X-Series Performance Verification and
Adjustment Software must be used. All adjustments are automated. This software is included in
the N7814A, Keysight X-Series Signal Analyzer Calibration Application software.
Installation Note N9020-90254 5
Option BU1/BU2/BU3, 40 MHz to 85/125/160 MHz Analysis Bandwidth Upgrade
Installation Kit Parts List
Quantity Description Keysight Part Number
1 A25 Wideband Analog IF N9020-60044
1 A26 Wideband Digital IF N9020-60311
1 Opt BU1/BU2/BU3 Cable Kit with Wire Markers
(includes cables W51 through W56, listed below)
N9020-60303
1 Cable Assembly, Flat Flexible 80-conductor 3-in-LG (W44) 8121-1854
1 Cable Assembly, Coaxial 700 mm LG (W20) 8121-1400a
with ends labeled ‘705’
and ‘6’
a.This cable is included in the Option BU1/BU2/BU3 Cable Kit with Wire Markers, p/n N9020-60303
1 Cable Assembly, Coaxial 530 mm LG (W51) 8121-1401a
with ends labeled ‘301’
and ‘718’
1 Cable Assembly, Coaxial 380 mm LG (W52) 8121-2288a
with ends labeled ‘102’
and ‘15’
1 Cable Assembly, Coaxial 380 mm LG (W54) 8121-2288a
with ends labeled ‘716’
and ‘14’
1 Cable Assembly, Coaxial 480 mm LG (W55) 8121-2290a
with ends labeled ‘805’
and ‘17’
1 Cable Assembly, Coaxial 710 mm LG (W56) 8121-2291a
with ends labeled ‘806’
and ‘726’
1 Cable Assembly, Coaxial 570 mm LG (W53) 8121-2292a
with ends labeled ‘901’
and ‘101’
2 Cable Tie 1400-0249
14 Screw, M3 x 0.5, (6 mm long), flathead 0515-1946
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
1 Installation Note This note
6Installation Note N9020-90254
Option BU1/BU2/BU3, 40 MHz to 85/125/160 MHz Analysis Bandwidth Upgrade
Tools Required
— T-10 TORX Driver
— T-20 TORX Driver
— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later)
— Test equipment and computer supported by the X-Series Performance Tests and Adjustment
Software
— MXA Signal Analyzer Service Guide. This manual is available online at the following URL:
www.keysight.com/find/N9020B_service_guide
— Microsoft Windows based personal computer with internet access and USB port
— USB storage device with >2GB free memory
Initial Instrument Functionality Check
Power on the instrument and allow the instrument to boot up. Run an alignment and display the
measurement screen. (The instrument will probably display a spectrum analyzer screen and you will
see the instrument sweeping.)
There should be no alignment failures. If there are failures, investigate and fix the problem before
continuing.
Before you disassemble the instrument, turn the power switch to Standby. After the instrument
has completely shut down, unplug the instrument. Failure to unplug the instrument can result in
personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.
Installation Note N9020-90254 7
Installation Procedure
Installation Procedure
Analyzer Information
1. Connect a power cord to the analyzer and turn on the analyzer.
2. After the analyzer has completed turning on, press System, Show System. Make note of the
following information from the Show System screen:
Product Number ________________
Serial Number ________________
Instrument S/W Revision ________________
3. Check for the presence of the options listed below in the Show System screen. Put a check
mark or “X” after each option listed below that appears in the Show System menu.
N9020B-503 ______
N9020B-508 ______
N9020B-513 ______
N9020B-526 ______
N9020B-BBA ______
N9020B-B40 ______
N9020B-DP2 ______
N9020B-MPB ______
Refer to the following conditions:
—If the analyzer is not equipped with N9020B-B40, do not proceed with the installation of
this upgrade kit. If N9020B-B40 is not installed, other upgrade kits are available to upgrade
to 85 MHz, 125 MHz, or 160 MHz analysis bandwidth.
—If the analyzer has N9020B-BBA, do not proceed with the installation of this kit. N9020B
analyzers with Option BBA do not have sufficient room to install the two additional boards
required for analysis bandwidths of 85 MHz and wider.
—If the N9020B-MPB is not already present and either frequency range option N9020B-508,
N9020B-513, or N9020B-526 is present, it will be necessary to upgrade the analyzer to add
option N9020B-MPB before installing this kit. Refer to
http://www.keysight.com/find/mxa_upgrades for details on how to upgrade to N9020B-
MPB.
Do not attempt to install this kit on an N9020A. Although much of the hardware is identical, the
licenses included in this kit will only work on an N9020B.
8Installation Note N9020-90254
Installation Procedure
Update Instrument Software
Updating the instrument software and installing the necessary licenses before installing the new
hardware will help ensure that the hardware installation was successful.
Go to the following website and determine whether or not the analyzer has the latest instrument
software already installed:
http://www.keysight.com/find/xseries_software
If the analyzer does not have the latest instrument software already installed, download and install
the latest version.
Installation Note N9020-90254 9
Installation Procedure
Licensing the New Options
License Installation Procedure over USB
1. Locate the Option Upgrade Entitlement Certificate (5964-5178) in the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming the upgrade products from the Certificate(s), you will receive one or two
e-mails, each with an attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File(s) to the root directory of the USB Storage Device.
6. Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to
another USB port. Windows will detect the new hardware and may display the configuration
menu shown in Figure 1. This menu may be configured according to your preferences.
Figure 1 USB Storage Device Configuration Menu
10 Installation Note N9020-90254
Installation Procedure
7. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message similar to the one shown in Figure 2. If the license file contains
multiple licenses, multiple “Successful License Installation” messages will appear. Wait until
all licenses have been consumed before removing the USB Storage Device.
Figure 2 Successful License Installation
If you will also be installing any of the following upgrade products:
N9020BU-MPB
N9020BU-CR3, 2nd IF Output
N9020BU-CRP, Arbitrary IF Output
Now would be the best time to install the licenses for these other upgrades. By installing the
licenses now, the adjustments and performance verifications for these other upgrades will also
be performed.
Autres manuels pour N9020B
2
Table des matières
Autres manuels Keysight Technologies Instrument de mesure
Keysight Technologies
Keysight Technologies FieldFox N9912A104 Manuel utilisateur
Keysight Technologies
Keysight Technologies 86120B Manuel utilisateur
Keysight Technologies
Keysight Technologies B2900A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies B2980A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies N432A Manuel utilisateur
Keysight Technologies
Keysight Technologies MXA N9020A Manuel utilisateur
Keysight Technologies
Keysight Technologies E5061B Manuel utilisateur
Keysight Technologies
Keysight Technologies U1731C Manuel utilisateur
Keysight Technologies
Keysight Technologies M9451A Guide de l'utilisateur
Keysight Technologies
Keysight Technologies B2900A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies E4980A Manuel de l'opérateur
Keysight Technologies
Keysight Technologies FieldFox Manuel utilisateur
Keysight Technologies
Keysight Technologies N9020A Manuel d'installation et d'exploitation
Keysight Technologies
Keysight Technologies X8712A Manuel utilisateur
Keysight Technologies
Keysight Technologies B2900 Series Manuel utilisateur
Keysight Technologies
Keysight Technologies N8480 Series Manuel de service
Keysight Technologies
Keysight Technologies M9260A Guide de l'utilisateur
Keysight Technologies
Keysight Technologies E5061B Manuel utilisateur
Keysight Technologies
Keysight Technologies N8262A P Series Manuel utilisateur
Keysight Technologies
Keysight Technologies M8131A Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur