Keysight Technologies N9000A Manuel d'installation et d'exploitation

Keysight N9000A CXA Signal Analyzer

Option CR3

Wideband IF Output

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement

business has become Keysight Technologies. For

more information, go to www.keysight.com.

Installation Note

Part Number: N9000-90034

Printed in USA July 2014

*N9000-90034*

N9000-90034

Notice.

The information contained in this document is subject to change without notice.

KeysightTechnologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Keysight

Technologies shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Installation Note N9000-90034 3

Option CR3 - Wideband IF Output Installation Kit

Overview

This kit contains all of the instructions required to install option CR3 wideband IF output on an

Agilent N9000A CXA signal analyzer.

The procedure outlined in this document will guide you through the following steps, which will need

to be followed closely, and performed in the order defined:

1. Pre-upgrade Status Check

2. Hardware Installation

3. Update the Instrument Firmware

4. Install the License File

5. Installation Verification

Products Affected: CXA N9000A

Serial Numbers: CXA

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

1 Hours

0.5 Hour

4Installation Note N9000-90034

Option CR3 - Wideband IF Output Installation Kit

Installation Procedure

This installation note is part of an upgrade kit that provides all of the parts and instructions needed to

install the AUX IF assembly in an Agilent N9000A CXA signal analyzer.

Contents

Tools Required

❏Torx Driver T-10

❏Torx Driver T-20

❏9/16-inch nut driver

❏USB storage device >2GB free memory

Quantity Description Agilent Part Number

1 AUX IF Assembly N9000-60414

1 Ribbon Cable E4410-60162

1 Cable Assembly, DIF-Rear Panel Aux IF Out N9000-20108

1 Cable Assembly, RF-DIF N9000-20132

3 Screw M3*0.5 (8 mm) 0515-0372

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

Installation Note N9000-90034 5

Option CR3 - Wideband IF Output Installation Kit

1. Pre-Upgrade Status Check

Before performing this upgrade you will need to know the status of the instrument being upgraded in a

couple of areas.

Pre-Existing Issues and Error Messages

Power the instrument on and verify that the instrument will not only boot up, but that the signal

analyzer application software will load properly. This would include verifying that there are no

error messages displayed in the Status Bar of the application window.

If there are any problem with the instrument at this point, including the presence of any error

messages, either repair the instrument prior to proceeding with this upgrade or make detailed

notes of the instrument status in the space provided below and address them once this upgrade

has been completed if they continue to be present.

______________________________________________________________________________

____________________________________________________________________________

Pre-Upgrade Instrument Software Revision

Determine the current instrument software revision and record it in the space below by pressing

System, Show, System on the instrument.

Instrument S/W Revision: ______________________

6Installation Note N9000-90034

Option CR3 - Wideband IF Output Installation Kit

2. Hardware Installation

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Refer to the documentation that pertains to your instrument for information about

static-safe workstations and ordering static-safe accessories.

Removal

1. Turn off the instrument and remove the power cord from the rear panel.

2. Remove the outer case of the instrument.

a. Refer to Figure 1. Using the T-20 driver, remove the four screws (two on each side) (1) that

attach the handle strap (2) on each side of the instrument.

b. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet (4)

in place.

c. Pull the instrument cover (5) off towards the rear of the instrument.

Figure 1 Standard Instrument Outer Case Removal

3. Remove the Top Brace and Reference Bracket.

a. Refer to Figure 2. To remove the top brace (1), use the T-10 driver, remove the eight screws (3)

(0515-0372) attaching the top brace to the chassis, the six screws (4) (0515-1227) attaching the

top brace to the boards, and the four screws (4) attaching the top brace to the reference bracket.

Installation Note N9000-90034 7

Option CR3 - Wideband IF Output Installation Kit

b. To Remove the reference bracket (2) use the T-10 driver to remove the six screws (5) (including

two at the rear panel) attaching the reference bracket to the instrument and the four screws (4)

attaching the top brace to the reference bracket.

Figure 2 Top Brace and Reference Bracket Removal

8Installation Note N9000-90034

Option CR3 - Wideband IF Output Installation Kit

4. Refer to Figure 3 to remove the rear panel.

Figure 3 Rear Panel Removal

a. Remove the twenty screws (2) attaching the rear panel (1) to the chassis and to the reference

bracket. The rear panel can now be removed.

b. If W5 is installed on this instrument, remove W5 at the rear panel using a 9/16-inch nut driver,

and disconnect it from the RF assembly.

Installation Note N9000-90034 9

Option CR3 - Wideband IF Output Installation Kit

5. Refer to Figure 4 to remove the DIF board.

Figure 4 DIF Board Removal

a. Remove cable W4 and W6 from the bottom of the DIF board.

b. The DIF board can be removed from the chassis by pulling straight out the back.

10 Installation Note N9000-90034

Option CR3 - Wideband IF Output Installation Kit

6. Install the AUX IF assembly on the DIF board.

a. Refer to Figure 5, locate the AUX IF assembly and the ribbon cable in the upgrade kit and

install it on the upper side of the DIF board. Connect the E4410-60162 ribbon cable from DIF

board to AUX IF assembly.

Figure 5 AUX IF Assembly Installation A

b. Locate the three 0515-0372 screws in the upgrade kit. Refer to Figure 6, tighten the screws

from the bottom side of the DIF board to attach the AUX IF assembly on the upper side of the

DIF board.

Figure 6 AUX IF Assembly Installation B

Autres manuels pour N9000A

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies 8990B Manuel utilisateur

Keysight Technologies

Keysight Technologies B2900A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies U3810A Manuel utilisateur

Keysight Technologies

Keysight Technologies E4980A Manuel utilisateur

Keysight Technologies

Keysight Technologies UXA N9040B Manuel utilisateur

Keysight Technologies

Keysight Technologies U1733C Manuel utilisateur

Keysight Technologies

Keysight Technologies E5052B Manuel du propriétaire

Keysight Technologies

Keysight Technologies Option 503 Manuel utilisateur

Keysight Technologies

Keysight Technologies N9340B Manuel utilisateur

Keysight Technologies

Keysight Technologies InfiniiMax III Series Manuel utilisateur

Keysight Technologies

Keysight Technologies U9361F Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies M937 A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies E5072A Manuel utilisateur

Keysight Technologies

Keysight Technologies E5061B Manuel utilisateur

Keysight Technologies

Keysight Technologies B2900A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies FieldFox Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies E4980A Manuel de l'opérateur

Keysight Technologies

Keysight Technologies M9300A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies U2020 X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies M9393A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies X-Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N9320A RF Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur