Juniper JCS 1200 Manuel utilisateur

Autres manuels pour JCS 1200

6

Table des matières

Autres manuels Juniper Routeur réseau

Juniper

Juniper TX MATRIX PLUS Manuel utilisateur

Juniper

Juniper XRE200 - Manuel utilisateur

Juniper

Juniper EX4300 Instructions d'installation

Juniper

Juniper T1600 Instructions d'installation

Juniper

Juniper NetScreen-5GT Wireless Manuel utilisateur

Juniper

Juniper ACX1000 Manuel utilisateur

Juniper

Juniper M7i Instructions d'installation

Juniper

Juniper EX4600 Manuel utilisateur

Juniper

Juniper EX8200 Series Manuel utilisateur

Juniper

Juniper J2320 Manuel utilisateur

Juniper

Juniper J2320 Manuel utilisateur

Juniper

Juniper M-Series Manuel utilisateur

Juniper

Juniper T640 Instructions d'installation

Juniper

Juniper ACX5448-D Instructions d'installation

Juniper

Juniper MX2010 Manuel utilisateur

Juniper

Juniper MX960 Manuel utilisateur

Juniper

Juniper LN1000 - RELEASE NOTES 8-27-2010 Manuel utilisateur

Juniper

Juniper PTX1000 Instructions d'installation

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Instructions d'installation

Juniper

Juniper T4000 - Manuel utilisateur

Juniper

Juniper 6rd Manuel utilisateur

Juniper

Juniper T320 Manuel utilisateur

Juniper

Juniper J-Series Manuel utilisateur

Juniper

Juniper ACX2000 Instructions d'installation

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

Replacing a JCS 1200 Management Module or Module Filler

Topics include:

■Removing a JCS 1200 Management Module or Module Filler on page 1

■Installing a JCS 1200 Management Module or Module Filler on page 2

Removing a JCS 1200 Management Module or Module Filler

Figure 1 on page 1 shows how to remove and install a management module.

Figure 1: Removing and Installing a JCS 1200 Management Module

When you remove a management module, keep in mind the following:

■These instructions assume that the JCS 1200 platform is connected to power.

■If you are replacing the only management module in the JCS 1200 platform and

the management module is functioning, save the configuration file before you

proceed. For information about saving and restoring a configuration file, see the

JUNOS Protected System Domain Configuration Guide.

■If you have just installed a second management module in the JCS 1200 platform,

do not remove the first (primary) management module for up to 45 minutes;

the second (redundant) management module needs the time to receive initial

status information and firmware from the management module.

To remove a management module or module filler (see Figure 1 on page 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Pull the management module release handle to the open position. The module

moves out of the bay approximately 0.25 in. (0.6 cm).

3. Slide the management module out of the bay.

Replacing a JCS 1200 Management Module or Module Filler ■1

Installing a JCS 1200 Management Module or Module Filler

Figure 2 on page 2 shows how to remove and install a management module.

Figure 2: Removing and Installing a JCS 1200 Management Module

To install a management module or module filler (see Figure 2 on page 2):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Remove the management module filler, if one is installed.

3. Remove the management module interposer filler tray, if one is installed.

4. Install the management module interposer, if it is not already installed.

5. Make sure that the release handle on the management module is in the open

position.

6. Slide the management module into the management module bay until it stops.

7. Push the management module release handle to the closed position.

8. Connect any cables to the management module.

9. If the JCS 1200 platform is connected to power, make sure that the OK LED on

the management module is lit. If the management module is redundant, wait at

least 45 minutes for the modules to copy the configuration data before you make

any changes to the management module configuration.

Related Topics ■Preventing Electrostatic Discharge Damage to the JCS 1200 Platform

■JCS 1200 Management Module Description

■Replacing a JCS 1200 Management Module Filler Tray

■Locating the JCS 1200 Management Module Serial Number

2■Installing a JCS 1200 Management Module or Module Filler