Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 MODULE GUIDE REV... Manuel utilisateur

E Series™ Broadband

Services Routers

E120 and E320 Module Guide

Release

11.3.x

Published: 2010-10-01

This guide provides an overview and description of the line modules (LMs), switch route

processor (SRP) modules, switch fabric modules (SFMs), and input/output adapters

(IOAs) available for the Juniper Networks E120 and E320 Broadband Services Routers.

NOTE: A release may support multiple versions of a module or IOA. For

information, see Software Compatibility in JunosE System Basics Configuration

Guide, Chapter 6, Managing Modules.

Table 1 on page 3 lists the modules and IOAs supported by the router.

This guide also contains the following appendixes:

•IOA Protocol Support on page 49

•Module and Slot Combinations on page 73

•Module Name Cross-Reference Information on page 77

•Product Reclamation and Recycling Program on page 79

For more information about E120 routers, E320 routers, modules, and IOAs, refer to the

following guides:

•Modules that have reached end-of-life—E Series End-of-Life Module Guide

•Module installation and maintenance—E120 and E320 Hardware Guide

•Managing routers—JunosE System Basics Configuration Guide

•Configuring modules—JunosE Link Layer Configuration Guide

E120 and E320 11.3.x Module Guide

Table 1: Modules and IOAs

PageFirst JunosE SupportModule LabelModule/IOA Type

Line Module

57.0.1ES2

LM-4

77.2.0ES2

10G

UPLINK

LM-10 Uplink

98.0.0ES2

10G LM

LM-10

1110.1.0ES2

10G ADV LM

LM-10 ADV

SRP Module

127.0.1SRP-100SRP-100

148.2.0SRP-120SRP-120

167.3.0SRP-320SRP-320

SFM Module

187.0.1SFM-100SFM-100

198.2.0SFM-120SFM-120

207.3.0SFM-320SFM-320

Gigabit Ethernet IOA

217.0.1ES2-S1

GE-4

IOA

GE-4 IOA

257.2.0ES2-S1

GE-8

IOA

GE-8 IOA

299.0.0ES2-S3

GE-20

IOA

GE-20 IOA

337.2.0ES2-S2

10GE PR

IOA

10GE PR IOA

OC3/STM1 ATM IOA

Table 1: Modules and IOAs (continued)

PageFirst JunosE SupportModule LabelModule/IOA Type

377.0.1ES2-S1

OC3-8

STM1

ATM IOA

OC3/STM1-8 ATM IOA

OC12/STM4 ATM IOA

397.0.1ES2-S1

OC12-2

STM4

ATM IOA

OC12/STM4-2 ATM IOA

OC12/STM4 POS IOA

417.0.1ES2-S1

OC12-2

STM4

POS IOA

OC12/STM4-2 POS IOA

OC48/STM16 IOA

437.0.1ES2-S1

OC48

STM16

POS IOA

OC48/STM16 POS IOA

Redundancy IOA

457.0.1ES2-S1

REDUND

IOA

REDUND IOA

Service IOA

467.0.1ES2-S1

SERVICE

IOA

SERVICE IOA

SRP IOA

477.0.1SRP IOASRP IOA

E120 and E320 11.3.x Module Guide

LM-4 Line Module

ES2 4G LM

Module label

•Not applicable

Number of ports

•First supported: 7.0.1

Software release

•176 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Responsible for processing data traffic

•Pairs with IOAs to process data from different types of network connections

Description

•FFA ASIC

Type

•Supports a line rate of 128–byte packets on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot

2 and slot 4).

•The 320–Gbps switch fabric allocates 10 Gbps of overall bandwidth to each line

module slot. The line interface on the ES2 4G LM when installed in a 320 Gbps

fabric configuration is 3.9 Gbps; you can achieve this rate with random packet sizes

in the range 64–1518 bytes or a mixture of packet sizes that represent Internet mix

traffic (IMIX).

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for

more information.

Capability

•Not applicable

Software features

•E320 router

•E120 router

Model compatibility

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 4G LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

LM-4 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

LM-10 Uplink Line Module

ES2 10G UPLINK LM

Module label

•Not applicable

Number of ports

•First supported: 7.2.0

Software release

•150 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Processes up to 10 Gb of data traffic

•Pairs with ES2–S2 10GE PR IOA only

•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)

•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled

•If you install a LM-10 Uplink module next to a configured line module that is already

installed in slot 3 or slot 5, the LM-10 Uplink module will be disabled

•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10

Uplink module, the non-LM-10 Uplink module will be disabled

•In a SRP-120 and SRP-320 configuration, it can be installed in any slot

Description

•IXP network processor

Type

•Supports a line rate of 128–byte frames on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2

and slot 4).

•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth

to each line module slot.

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more

information.

Capability

•Not applicable

Software features

•E320 router

•E120 router

Model compatibility

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 10G UPLINK LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

LM-10 Uplink Line Module

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

LM-10 Line Module

ES2 10G LM

Module label

•Not applicable

Number of ports

•First supported: 8.0.0

Software release

•198 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Processes up to 10 Gb of data traffic

•Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA

•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)

•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled

•If you install the LM-10 module next to a configured line module that is already

installed in slot 3 or slot 5, the LM-10 module will be disabled

•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10

module, the non-LM-10 module will be disabled

•In a SRP-120 and SRP-320 configuration, it can be installed in any slot

Description

•TFA ASIC

Type

•Supports a line rate of 128–byte frames on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2

and slot 4).

•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth

to each line module slot.

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more

information.

Capability

•Not applicable

Software features

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 10G LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

LM-10 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Juniper Routeur réseau

Juniper

Juniper M10i Manuel utilisateur

Juniper

Juniper M120 Manuel utilisateur

Juniper

Juniper J2300 Manuel utilisateur

Juniper

Juniper ACX2200 Manuel utilisateur

Juniper

Juniper ACX5448 Manuel utilisateur

Juniper

Juniper EX6210 Manuel utilisateur

Juniper

Juniper Internet Router M160 Instructions d'installation

Juniper

Juniper ACX6160 Manuel utilisateur

Juniper

Juniper ERX-310 Manuel utilisateur

Juniper

Juniper ACX1000 Manuel utilisateur

Juniper

Juniper MX150 Instructions d'installation

Juniper

Juniper PTX10008 Manuel utilisateur

Juniper

Juniper NetScreen-5GT Wireless Manuel utilisateur

Juniper

Juniper ACX4000 Manuel utilisateur

Juniper

Juniper ACX5048 Instructions d'installation

Juniper

Juniper MX204 Manuel utilisateur

Juniper

Juniper MX150 Manuel utilisateur

Juniper

Juniper MX104 Instructions d'installation

Juniper

Juniper PTX10003-160C Manuel utilisateur

Juniper

Juniper LN1000 - RELEASE NOTES 8-27-2010 Manuel utilisateur

Juniper

Juniper ACX Series Manuel utilisateur

Juniper

Juniper PTX10008 Instructions d'installation

Juniper

Juniper Day One+ MX304 Manuel utilisateur

Juniper

Juniper M320 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité