Interlogix FW5.1 Manuel utilisateur

P/N 1073029-EN • REV B • ISS 16JUN15

TruVision IP PTZ

Camera FW5.1

Installation Guide

Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies

Trademarks and

patents

The Product Name and logo are trademarks of United Technologies.

Other trade names used in this document may be trademarks or registered trademarks of the

manufacturers or vendors of the respective products.

Manufacturer Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

FCC compliance Class A: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference

(2) This Device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Canada This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du Canada.

European Union

directives

12004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this device is in

compliance with the essential requirements and other relevant provisions of Directive

2004/108/EC.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as

unsorted municipal waste in the European Union. For proper recycling, return this product to

your local supplier upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of

as unsorted municipal waste in the European Union. See the product documentation for

specific battery information. The battery is marked with this symbol, which may include

lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,

return the battery to your supplier or to a designated collection point. For more

information see: www.recyclethis.info.

Contact information

For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.

Installation Guide 3

Content

Introduction 3

Product overview 4

Before you begin 4

Installation environment 5

Camera description 5

Connections 7

Installing a camera 9

Pendant-mount camera 9

TVP-1122/3122 pendant-mount camera 11

Flush-mount camera 11

Surface-mount camera 14

Using the camera with an Interlogix NVR or Hybrid DVR or

another system 18

Using the camera with TruVision Navigator 18

Accessing the camera over the internet 18

Specifications 20

Pin definitions 21

Introduction

This installation guide provides basic information on setting

up and using the camera. Detailed information on the

cameras can be found in the configuration manual.

4 Installation Guide

Product overview

This is the installation guide for following TruVision IP PTZ

camera models:

TVP-1101 (1.3 MPX pendant, 20X, PAL)

TVP-3101 (1.3 MPX pendant, 20X, NTSC)

TVP-1102 (1.3 MPX surface, 20X, PAL)

TVP-3102 (1.3 MPX surface, 20X, NTSC)

TVP-1103 (1.3 MPX flush, 20X, PAL)

TVP-3103 (1.3 MPX flush, 20X, NTSC)

TVP-1104 (2 MPX pendant, 20X, PAL)

TVP-3104 (2 MPX pendant, 20X, NTSC)

TVP-1105 (2 MPX surface, 20X, PAL)

TVP-3105 (2 MPX surface, 20X, NTSC)

TVP-1106 (2 MPX flush, 20X, PAL)

TVP-3106 (2 MPX flush, 20X, NTSC)

TVP-1107 (2 MPX pendant, 30X, PAL)

TVP-3107 (2 MPX pendant, 30X, NTSC)

TVP-1122 (2 MPX pendant, 30X, IR, PAL)

TVP-3122 (2 MPX pendant, 30X, IR, NTSC)

Before you begin

Unpack everything. Check the items for damage, and verify

that all items are included. The camera is shipped with the

following items:

Dome camera

Installation Guide

CD with the Configuration Manual and Device Manager

Installation Guide 5

Installation environment

When installing your camera, consider these factors:

•Place the camera in a secure location.

•Ensure that the camera is in a well-ventilated area.

•Do not expose the camera to rain or moisture.

Caution: Risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries according to the

instructions.

Camera description

Figure 1: Overview of the dome camera (pendant-mount

shown)

6 Installation Guide

TVP-1122/3122 cameras only:

1. Power supply cord

Connect 24 VAC power supply

2. Video output

Connect the BNC connector to a

CCTV monitor

3. Ethernet RJ45 connector.

Connect to the network devices

Connect to the PoE+ switch

4. Alarm input/outputs and audio

in/out port

5. Housing

6. Bubble

7. Metal housing

8. IR LEDs

9. Camera

Installation Guide 7

Connections

There are seven built-in alarm inputs to use as internal

alarm triggers and two alarm built-in outputs in the camera

housing. These connections do not apply to the TVP-

1122/3122 cameras.

Note: The DIP switches are not used.

Figure 2: Connections to the circuit board (excludes

TVP-1122/3122)

1. Power supply: Connect +24 VAC power supply and GND.

2. RJ45 connector: Connect to the network.

Caution: The RJ45 connector on the camera module is not for connecting

the network. It is an RS-232 port for troubleshooting.

3. Alarm inputs 3 to 7: Connect to up to five alarm input devices.

4. GND

5. Alarm inputs 1 and 2: Connect to up to two alarm input devices.

6. Alarm outputs 1 and 2: Connect up to two output devices

7. AIN, AOUT: Connect audio input, audio output, and GND to the audio

terminals.

8. VIDEO: Connect a CCTV monitor to the video terminals.

Alarm input and output connections

The alarm output can be used to turn on and off an external

alarm device. Connect a 30 VDC/1 A external power supply

8 Installation Guide

to the alarm output. If using an AC power supply, an

external relay must be used to prevent electric shock and

damage to the device. See Figure 3 below.

Figure 3: External alarm output

Direct current:

Dome camera

relay output

Alternating current:

Dome camera

relay output

Installation Guide 9

Installing a camera

Pendant-mount camera

1. Prepare the mounting surface and install the camera

bracket.

2. Unscrew the bubble from the camera and remove the

protective tape from the PTZ module (excluding TVP-

1122).

3. Press the two tabs on either side of the PTZ module

and remove the module from the camera housing

(excluding TVP-1122).

4. Route the cables from the pendant bracket as shown

below.

RED AC24V

YELLOW/GREEN

BLACK AC24V

10 Installation Guide

5. Attach the safety cable to the bracket and connect the

cables to the PCB of the module through the cable entry

hole on top of the housing.

Safety cable

Note: If alarm and audio input/output relays are to be

used, also connect them to the PCB of the module.

Caution:The safety cable is made of metal. Please

ensure that it does not touch the PCB of the module.

6. Attach the camera housing to the bracket using the

screws enclosed with the bracket.

7. Insert the PTZ module into the housing:

Position the tabs on the PTZ module by aligning the

arrow label on the module with those on the housing

(see below). The module should firmly snap into

position. If using a SD card, insert it into the module

before inserting the module into the housing.

Autres manuels pour FW5.1

Table des matières

Autres manuels Interlogix Caméra IP

Interlogix

Interlogix TruVision Line Feuille d'instructions

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TruVision 11 Series Manuel utilisateur

Interlogix

Interlogix TruVision 6 Series Manuel utilisateur

Interlogix

Interlogix TruVision TVB-4409 Manuel

Interlogix

Interlogix TVC-5125BE-3 Manuel utilisateur

Interlogix

Interlogix TVD-TIR6-MR Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix VD-IP-XP4DNP Manuel utilisateur

Interlogix

Interlogix TVB-1101 Feuille d'instructions

Interlogix

Interlogix UltraSync RS-3230 Feuille d'instructions

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TruVision TVT-2202 Manuel utilisateur

Interlogix

Interlogix TruVision TVP-1101 Feuille d'instructions

Interlogix

Interlogix TVB-1101 Manuel utilisateur

Interlogix

Interlogix TruVision Bullet IR TVC-BIR6-SR Manuel utilisateur

Interlogix

Interlogix TVB-2203 Manuel utilisateur

Interlogix

Interlogix TruVision TVB2406 Manuel utilisateur

Interlogix

Interlogix UltraSync RS-3230 Manuel utilisateur

Interlogix

Interlogix UltraView IP XP4 Box Day/Night Range Camera Manuel utilisateur

Interlogix

Interlogix VC-IP-XP4DN-HR Manuel utilisateur

Interlogix

Interlogix TVB-5302 Feuille d'instructions

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur