ICP DAS USA M-7060 Manuel utilisateur



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7060

4-channel Digital Input and 4-channel Relay

Output Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7060_m_7060d

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The 7060 series provides 4 digital input channels, 2 Form A and 2 Form C signal relay output

channels, while the M-7060P provides 4 digital input channels, 2 Form A and 2 Form C power

relay output channels. All digital input channels can be used as 16-bit counters. In addition, the

digital input channels can be selected either as sink- or source-type via wire connections. The

“D” versions of the 7060 series provide eight LED indicators that can be used to monitor the

status of the digital input and relay output. The “M” versions of the 7060 series support both the

Modbus RTU and DCON protocols, which can be configured via software. There are also

options for configuring power-on and safe values. 4 kV ESD protection and 3750 VDC intra-

module isolation are also provided to enhance noise protection capabilities in industrial

environments. The 7060 series is the ideal solution for small signal switching applications, while

the M-7060P is the perfect solution for high power applications.

2.TerminalAssignment



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3.Block/WiringDiagram



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

。 Module Address: 01

。 DIO Type: Type 40

。 Baud Rate: 9600 bps

。 Checksum disabled

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA MDC-714i Manuel utilisateur

ICP DAS USA

ICP DAS USA PM-3133i Manuel utilisateur

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manuel utilisateur

ICP DAS USA

ICP DAS USA XP-8000-Atom-CE6 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7000 series Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2026 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA USB-87P1 Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3071 Manuel utilisateur

ICP DAS USA

ICP DAS USA tSH-725 Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3227 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-87004W Manuel utilisateur

ICP DAS USA

ICP DAS USA PDS-220F Series Manuel d'utilisation et d'entretien

ICP DAS USA

ICP DAS USA M-7026 Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2050 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7088 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8094 Manuel de la liste des pièces

ICP DAS USA

ICP DAS USA PM-4324 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA tET Series Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7041D Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-257 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA iWSN-110X Series Manuel utilisateur

ICP DAS USA

ICP DAS USA tPET-P6 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur