ICP DAS USA I-7041 Manuel utilisateur

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7041

14 Channel Isolated Digital Input Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7041

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The I-7041 provides 14 channels for digital input, each of which features

photo couple isolation. In addition, sink- or source-type digital input can be

selected via wire connections, and all channels are able to be used as 16-

bit counters. 4 kV ESD protection and 3750 VDC intra-module isolation are

standard. ICPDAS recommends selecting the "P" version of the digital input

module for industrial use.

2. Terminal Assignment

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the I-7043 DIO modules are as follows:

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

。J3 set to INIT mode enabled for I-7043/43D a

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA PET-7053 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA LP-8 21 Series Instructions générales

ICP DAS USA

ICP DAS USA ET-7000 series Manuel utilisateur

ICP DAS USA

ICP DAS USA PM-3033 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA WP-5231 Manuel utilisateur

ICP DAS USA

ICP DAS USA WF-2017 Manuel utilisateur

ICP DAS USA

ICP DAS USA DL-10 Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2016N Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7063D Manuel utilisateur

ICP DAS USA

ICP DAS USA GTP-230 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-87004W Manuel utilisateur

ICP DAS USA

ICP DAS USA WISE-5801-MTCP Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7016D Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-6000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2060 Manuel utilisateur

ICP DAS USA

ICP DAS USA DS-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA FR-32R Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7H16M Series Manuel utilisateur

ICP DAS USA

ICP DAS USA PDS-5000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7019Z Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur