ICP DAS USA TM-P3R3 Manuel utilisateur

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-P3R3

3-channel Isolated Digital Input and 3-

channel Relay Output Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_p3r3.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-P3R3 provides 3 channels for digital input and 3 channels for relay output, each

of which features photocouple isolation. All output channels are form A type relays,

while input is based on sink- or souce-type using a wire connecion. All input channels

can be used an 16-bit counters. There are options for configuring power-on and safe

digital output values. 4 kV ESD protection and 3750 VDC intra-module isolation are also

provided.

2. Terminal Assignment

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

•Use 26-12 AWG wire for signal

connections.

•Strip the wire to a length of

7±0.5mm.

•Use a crimp terminal for wiring.

•Avoid high-voltage cables and

power equipment as much as

possible.

•For RS-485 communication, use

insulated and twisted pair 24 AWG

wire, e.g. Belden 9841.

4. Default Settings

Default settings for the tM-P3R3 module are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA PET-7261 Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2061 Manuel utilisateur

ICP DAS USA

ICP DAS USA tGW-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD8C Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2026 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-87004W Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7016D Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3784M Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7H16M Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7218Z Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8123W Guide de configuration

ICP DAS USA

ICP DAS USA ZT-257 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2050 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2260 Manuel utilisateur

ICP DAS USA

ICP DAS USA PROFI-5045 Manuel utilisateur

ICP DAS USA

ICP DAS USA USB-87P1 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-87P2 Manuel utilisateur

ICP DAS USA

ICP DAS USA MN-3253 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA DS-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8092F Manuel de la liste des pièces

ICP DAS USA

ICP DAS USA M-7026 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

ICP DAS USA tM-P3R3 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques