ICP DAS USA I-7083 Manuel utilisateur

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1

I-7083

3-axis, 32-bit Encoder Counter Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7083

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The I-7083 and I-7083B are 3-axis high speed encoder modules. Each axis on the module can be

independently confi gured as one of Quadrant, Pulse/Dir or CW/CCW input mode with a

maximum input rate of 1 MHz. The high-end specifications of the I-7083/I-7083B and complete

software support make it ideal for a wide range of applications in position measurement of

motion systems working in industrial and laboratory environments. The I-7083B is an improved

version of I-7083 with virtual battery backup function for counter value.

2. Terminal Assignment

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the I-7083 module is as follows:

- address=01

- baud rate=9600

- checksum disable

- data=1 start+8 data+1 stop(no parity)

- type=53

- Mode= 5 for 7083, L=0, XOR=1, CwCcw mode

D for 7083B, L=1, XOR=1, CwCcw mode

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Autres manuels pour I-7083

1

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA GW-7552-M Manuel utilisateur

ICP DAS USA

ICP DAS USA tDS-700-T Series Manuel utilisateur

ICP DAS USA

ICP DAS USA PISO-CPM100U-D/T Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7063 Manuel utilisateur

ICP DAS USA

ICP DAS USA PET-7261 Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7053D Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7080 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7052D Manuel utilisateur

ICP DAS USA

ICP DAS USA XP-8000-Atom-CE6 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7069D Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-TH8 Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2000 Series Guide d'installation

ICP DAS USA

ICP DAS USA HRT-370 Manuel utilisateur

ICP DAS USA

ICP DAS USA PROFI-5045 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-87004W Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2053 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7015 Manuel utilisateur

ICP DAS USA

ICP DAS USA DS-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3784M Manuel utilisateur

ICP DAS USA

ICP DAS USA tSG-3781B Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8092F Manuel de la liste des pièces

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur