ICP DAS USA 7188EN Guide d'installation

分類/Classification

tDS

tGW

PETL/tET/tPET

DS/PDS/PPDS

tM-752N

I/O Card

VXC Card

VxComm

7188EN

作者/Author

Tammy

日期/Date

2016-01-12

編號/NO.

FAQ-043

Q: How to enable web server for the PDS/7188EN series module?

A: The PDS/7188EN series module contains a built-in web server that allows the settings for the module to

be remotely modified via a web interface. When the web server has been disabled (Web Server = 0), refer

to the following two methods to enable the web server.

Method 1: Enable web server on PDS by using “console port and command”.Follow the procedure

described below:

1. Power off the PDS module.

2. Connect the download-cable (CA0910), between the PDS and COM4 of the development PC.

3. Wire the CA-0910 to PDS, as follows:

Connect the CA-0910.TX with PDS.TxD

Connect the CA-0910.RX with PDS.RxD

Connect the CA-0910.GND with PDS.GND

4. Set the “Init/Normal Switch”on the PDS module to the in “Init”position.

(Or connect the INIT* pin to the GND pin.)

5. Power on the PDS module.

6. Unzip the “7188XW_yyyymmdd.zip” file on the PC. The “7188XW_yyyymmdd.zip”can be obtained

from the ICP DAS web site (http://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/).

7. Open “Notepad”text editor for Windows and type the command: C4 B115200 P0D8 S1, and then save

the file as “7188xw.ini”in the same directory of 7188XW.exe.

8. Execute “7188XW.EXE”and press [Enter] key.

9. Settings configuration command:

The following is an example of a HTTP configuration.

Command

Description

HTTP= 1

Enables the Web Server.

HTTP= 0

Disables the Web Server.

Enable Web Server

C: COM Port of the development PC (e.g., C4)

B: Baud Rate (e.g., B115200)

P: Parity None (e.g., P0)

D: Data Bits (e.g., D8)

S: Stop Bits (e.g., S1)

Method 2: Enable web server on PDS by using “TCP port 10000”.Follow the procedure described below:

1. Ensure that the network settings on the Host PC have been correctly configured and are functioning

normally. Connect both the PDS module and the Host PC to the same sub network or the same

Ethernet Switch, and apply power to the PDS module.

2. Configure the correct network settings for the required PDS module. Refer to PDS Quick Start Guide for

more detailed information.

(http://ftp.icpdas.com/pub/cd/8000cd/napdos/pds/pds-700/document/quick_start/)

3. Download the “Terminal.exe”on your PC, or use other telnet client program. The “Terminal.exe”can

be downloaded from the ICP DAS web site.

(http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/)

4. Double click the “Terminal.exe”to open “Configuration Settings”dialog box.

5. Click the “TCP/IP Port”tab to configure the parameters as follows:

5-1: Type the “IP address of the PDS module”in the “IP Address”field.

5-2: Type the “10000”in the “TCP/IP Port”field.

5-3: Click the “Open COM”button.



6. Select the “Hex/Text”option in the “Display”filed and settings configuration command:

Command

Description

26SAVE=1, HTTP=1

Enables the Web Server and save the configuration to EEPROM.

26SAVE=1, HTTP=0

Disables the Web Server and save the configuration to EEPROM.

7. Type the “26SAVE=1, HTTP=1”string in the “send”field then click the “Send”button.

8. If the response is received, it will be displayed in the received field that means the success.

9. Reboot the PDS module to complete the configuration.







Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA tPET-P2R2 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7002 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA PM-3033 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2570 Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7053D Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2026 Manuel utilisateur

ICP DAS USA

ICP DAS USA tPET-P6 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7041 Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8124W Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3071 Manuel utilisateur

ICP DAS USA

ICP DAS USA tSH-734 Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2050 Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3227 Manuel utilisateur

ICP DAS USA

ICP DAS USA WF-2051 Manuel utilisateur

ICP DAS USA

ICP DAS USA IR-712A Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7033D Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7015 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7033 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7016D Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7017R Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur