ICP DAS USA M-7024 Manuel utilisateur

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7024

4 Channel Analog Output Data Acquisition

Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7024.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7024 is a 14-bit 4-channel analog output module that provides current and

voltage outputs. There are options for power-on values and safe values. It features

3000 VDC intra-module isolation.

The M-7024/M-7024R support Modbus RTU and DCON protocols and can be

configured via software.

2. Terminal Assignment

3. Block/ Wiring Diagram

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the M-7024 module are as follows:

▫Protocol: Modbus RTU

▫Module address: 01

▫Analog output type: 0 ~ +10 V

▫Baud Rate: 9600 bps

▫Engineering unit format

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6. Configuration I/O module setting on PC

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

Sub-function 04h of Function 46h, see user manual Section 3.3.2

Sub-function 06h of Function 46h, see user manual Section 3.3.4

Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.

M-7024 4 Channel AO DAQ Module - QuickStart (Jul/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA PDS-220F Series Manuel utilisateur

ICP DAS USA

ICP DAS USA WP-5231 Manuel utilisateur

ICP DAS USA

ICP DAS USA HRT-711 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7218Z Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7088 Manuel utilisateur

ICP DAS USA

ICP DAS USA FR-32R Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2060 Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3784M Manuel utilisateur

ICP DAS USA

ICP DAS USA tGW-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA tSG-3781B Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7080 Manuel utilisateur

ICP DAS USA

ICP DAS USA tSH-725 Manuel utilisateur

ICP DAS USA

ICP DAS USA iWSN-110X Series Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7065 Manuel utilisateur

ICP DAS USA

ICP DAS USA LP-8 4 Series Instructions générales

ICP DAS USA

ICP DAS USA ET-7000 series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA LinPAC-51 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA CAN-8123 Manuel utilisateur

ICP DAS USA

ICP DAS USA tET-P2A2 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7026 Manuel utilisateur

ICP DAS USA

ICP DAS USA PROFI-5045 Manuel utilisateur

ICP DAS USA

ICP DAS USA XP-8000-Atom-CE6 Manuel utilisateur

ICP DAS USA

ICP DAS USA tSH-735 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur