IBM TotalStorage NAS 100 Manuel utilisateur

IBM TotalStorage NAS 100

Rack Installation Instructions

򔻐򗗠򙳰

IBM TotalStorage NAS 100

Rack Installation Instructions

򔻐򗗠򙳰

First Edition (August 2002)

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

IBM TotalStorage

™

NAS 100 Rack Installation Instructions

Checking the rack installation kit

Items that you find in the kit:

vTwo telescopic slide rails

vFour brackets

vTwo mounting ears

vOne cable spiral wrap and eight cable ties

vAssorted hardware, including cage nuts, clip nuts, screws, nuts, and washers

vOne Rack Installation Instructions (this manual)

Items that you provide:

vOne Phillips #2 screwdriver

vOne flat-blade screwdriver (if you are using cage nuts)

vOne nutdriver or pair of pliers

Attaching the brackets

The following procedure explains how to attach the brackets to the telescopic slide

rails.

1. Extend the inner server slide rail as far as it will go.

2. Pull the white spring tab on the server slide rail towards its open end and

remove the server slide rail. Set it aside for attaching to the NAS 100 later.

1 Server slide rail

2 Spring tab

3 Telescopic slide rail

2NAS 100 Rack Installation Instructions

3. Attach the first bracket to the front end (the white end) of the telescopic slide

rail:

a. Locate the alignment screw hole on the front end of the outer telescopic

slide rail and align the bracket with it. The alignment screw hole establishes

where each screw will go in relation to the bracket. For most installations,

the alignment screw hole and bracket alignment will be the one illustrated in

the following figure.

1 Alignment screw hole

2 Bracket

3 Outer telescopic slide rail

Note: You will have to slide the inner ball-bearing slide rail and the inner

telescopic slide rail back and forth to align the oval cutout with the

screw hole so that you can insert the screw.

b. Insert an M4 screw through the bracket and in the alignment screw hole,

fasten a washer and an M4 nut to it, and firmly tighten them. Repeat this

step with three more screws in the remaining holes.

4. Extend the slide rails fully.

IBM TotalStorage

™

NAS 100 Rack Installation Instructions 3

5. Loosely attach the next bracket to the back end of the telescopic slide rail with

four more M4 screws, washers, and nuts, as shown in the following figure.

1 Telescopic slide rail

2 Bracket

Note: Do not completely tighten these screws until you install the slide rail into

the rack. This will make attaching the slide rail to the rack much easier.

After the slide rail is attached to the rack, you can tighten the screws on

the back bracket.

6. Hold the slide rails with the attached brackets up to the rack and check that the

slide rails and brackets will fit in the rack. Make any necessary adjustments to

the back end of the slide rail and its bracket.

7. Repeat this process with the other telescopic slide rail and brackets.

Note: Make sure that you install the screws in the other telescopic slide rail in

exactly the same places that you installed them in the first telescopic

slide rail.

4NAS 100 Rack Installation Instructions

Mounting the slide rails on the rack

The following procedure explains how to attach the telescopic slide rails to the rack.

1. Determine where on the rack you want to mount the NAS 100.

2. Depending on your rack type, use a screwdriver to insert the cage nuts or slide

the clip nuts into the appropriate holes. You will install two nuts on each side of

the back of the rack and three nuts on each side of the front of the rack (the top

nut is used for the mounting ear on the front of the NAS 100).

Note: Make sure that you insert each of the bottom nuts at the same height on

the rack so that the installed NAS 100 will be level.

1 Cage or clip (shown) nut

2 Front bracket

3 Back bracket

4 Left/right front mounting template

5 Left/right back mounting template

IBM TotalStorage

™

NAS 100 Rack Installation Instructions 5

3. Secure the front end of the slide rail to the front of the rack with three M6

screws.

4. Secure the back end of the slide rail to the back of the rack with two M6

screws.

5. Tighten the rear bracket M4 screws of the telescopic slide rail.

6. Repeat this procedure with the other telescopic slide rail and brackets.

6NAS 100 Rack Installation Instructions

Table des matières

Autres manuels IBM Stockage

IBM

IBM 7131-105 Manuel utilisateur

IBM

IBM 7208 Manuel

IBM

IBM Netfinity Series Manuel du propriétaire

IBM

IBM Ultrastar 73LZX Manuel utilisateur

IBM

IBM Travelstar 10GT Manuel utilisateur

IBM

IBM SAN Volume Controller Manuel du propriétaire

IBM

IBM Ultrium Gen 6 Manuel utilisateur

IBM

IBM E Server x 100 Series Manuel utilisateur

IBM

IBM TotalStorage FAStT EXP700 Manuel utilisateur

IBM

IBM Universal Tape Library Manuel utilisateur

IBM

IBM System Storage N3220 Manuel

IBM

IBM System Storage TS2900 Manuel utilisateur

IBM

IBM 4mm DDS-2 Tape Autoloader Manuel utilisateur

IBM

IBM Travelstar 15GN Manuel utilisateur

IBM

IBM 3420 Manuel utilisateur

IBM

IBM FlashSystem 710 Manuel utilisateur

IBM

IBM Accesser 4105 Manuel utilisateur

IBM

IBM DS4700 EXPRESS Mode d'emploi

IBM

IBM totalstorage 200 Manuel utilisateur

IBM

IBM TotalStorage Ultrium 3580 L23 Manuel

IBM

IBM Power Systems Series Manuel utilisateur

IBM

IBM TS2250 Manuel utilisateur

IBM

IBM TU3 2104 Manuel

IBM

IBM 5280 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur