HP ESL E-Series Manuel utilisateur

StorageWorks

ESL E-Series

e2400-FC 2Gb

Interface

Controller

Upgrade

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is not hot-swappable.

It is necessary to power down the library

to replace this part.

Caution: Before continuing with this

procedure, ensure the following components

are upgraded to the necessary firmware

versions:

• library: 1.02 or greater

• Interface Manager: I130 or greater

• Command View ESL: 1.3.00 or greater

Refer to the HP StorageWorks Interface

Manager and Command View User Guide

for detailed procedures on checking

firmware revisions and making updates.

Note: These parts are only needed

during the initial library installation with

native Fibre Channel (FC) drives, and they

will not be used as part of this procedure.

For more information, refer to the HP

StorageWorks ESL E-Series Unpacking

and Installation Guide.

Note: These FC cables are not used if

your library contains only LTO4 tape

drives.

Inspect the contents of the kit.

StorageWorks

ESL E-Series

e2400-FC 2G

Interface

Controller

Upgrade

Caution:Part s can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is not hot-swappable.

It is necessary to power down the library

toreplace this part.

Caution:Before continuing with this

procedure, the library firmware must be at

version 1.02 or greater. Refer to the HP

StorageWorks Interface Manager and

Command ViewUser Guide for detailed

procedures.

Note: The cable clamp provided is not

needed for this procedure. If you are

upgrading a native Fibre Channel (FC)

library, this clamphas already been

installed. If you are upgrading a SCSI

library, use the clampthat is already

installed.

Power off the library.

Use your backup software to verify that the

picker is empty, or to empty the picker.

Press the power button located onthe front of

the library behind the laptop tray and wait

until the OCP goes blank.

Inspect the contents of the kit.

StorageWorks

ESLE-Series

e2400-FC2G

Interface

Controller

Upgrade

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartisnothot-swappable.

Itisnecessarytopowerdownthelibrary

toreplacethispart.

Note:Thecableclampprovidedisnot

neededforthisprocedure.Ifyouare

upgradinganativeFibreChannel(FC)

library,thisclamphasalreadybeen

installed.IfyouareupgradingaSCSI

library,usetheclampthatisalready

installed.

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

Poweroffthelibrary.

Useyourbackupsoftwaretoverifythatthe

pickerisempty,ortoemptythepicker.

Pressthepowerbuttonlocatedonthefrontof

thelibrarybehindthelaptoptrayandwait

untiltheOCPgoesblank.

ACT/

LNK

ACT/

LNK

PORT 1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

FIBRE

CHANNEL

With the FC ports located to your right as you face

the back of the library, slide the controller into the

card cage slot. Tighten the ejector handle screws.

Flip the two breaker switches off (to the left) at the

power distribution unit.

Hold the ejector handles so they extend toward

the outer edges of the controller.

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

Controller Installation

Using a #1 Phillips screwdriver, remove the blank

plate from the next available of the top six slots in

the card cage.

Open the back door of the library.

Power off the library.

a. Use your backup software to verify that the

picker is empty, or to empty the picker.

b. Press the power button located on the front

of the library and wait until the OCP goes

blank.

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT 0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

Connect each FC cable to the appropriately

labeled TD port on the interface controller. Once

connected, insert the FC cable bundle into the

cable clip to the right of the card cage.

Using a #2 Phillips screwdriver, remove the screw

from the clamp located on the lower right side

of the drive cluster. Route the FC cable bundle

through the clamp, then secure the clamp to

the cluster frame by replacing the screw.

FC Cable Configuration

FC cables are labeled near their connectors to

indicate which TD port to connect to each port on

the interface controller. Plan to first connect the

FC cables to the interface controller, then route

them through the cabinet, and finally, connect

them to the drive.

Drive TD Port

Route the cable through the

cable access holes in the sheet

metal on the right of the library

cabinet.

For drive clusters 0 through 2,

dip the excess cable length

down into the upper cable

access hole. For drive clusters 3

through 5, route the cables up through the lower

and upper access holes. Push the first set of cables

to the back of the library to create space for

additional cables. This will help prevent the cables

from becoming tangled.

FC Port A

FC Port B

Remove FC port A end caps

from the drive if present and

attach the FC cable. Be sure

to use the cable appropriately

labeled for the drive, identified as A, B, C, or D.

Note: Use FC port A only.

FC Port A

FC Port B

Insert the FC cable into the cable clip.

Caution: To avoid damaging

the FC cable, do not sharply bend or

pinch the cable. Allow a radial bend when

attaching the FC cable to the cable clip.

B A

D C

ACT/

LNK

ACT/

LNK

PORT 1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT2

FIBRE

CHANNEL

17 18

Connect the other end of the Ethernet cable to

the Ethernet port on the corresponding e2400-FC

2Gb interface controller.

Locate the small cable clamp on the upper right

corner of the first cluster frame. Using a #2

Phillips screwdriver, remove the screw from the

clamp. Place the Ethernet cable in the clamp,

then secure the clamp to the cluster frame by

replacing the screw.

Attach FC cables (not provided)

to the remaining interface controller FC ports. Route

them through access holes on the top or bottom of

the library cabinet and to a switch or an HBA.

Note: Use the labels provided to indicate

which drive cluster the FC cables are

interfacing with. Attach one label to each

end of the cables.

Ethernet Cable Connection

Connect the Ethernet cable to the

cluster controller card at port “E3.”

Note: You can use the labels provided

to indicate which drive cluster the FC

cables are interfacing with. Attach one

label to each end of the cables.

To help keep the FC cables clear of the drive

cluster below, attach the cables to the drive

handle on the lower right drive in the cluster

using the tie wrap provided.

Power on the library.

a. Verify that power cables are firmly in place.

b. Press the power button located on the front of

the library.

c. After several minutes, verify that the current

state of the library appears in the System

State display on the OCP (System On-line

or System Off-line).

Flip the two breaker switches on at the power

distribution unit.

ACT/

LNK

ACT/

LNK

PORT1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 0

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT1 PORT 0 ETHERNET

SERIAL

PWR

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

ACT/

LNK

ACT/

LNK

PORT 1 PORT 3

FIBRE

CHANNEL

FIBRE

CHANNEL

ACT/

LNK

PORT 2

FIBRE

CHANNEL

Verify that the power LED and Fibre link LEDs on

the controller are solid green. The link LEDs

indicate a good connection.

Close the back door of the library.

Configuration

Use HP StorageWorks Interface Manager

command-line interface or HP StorageWorks

Command View TL to verify detection of the

new controller, and to perform configuration

and firmware updates.

Refer to the HP StorageWorks Interface

Manager and Command View TL User Guide

for detailed procedures.

Getting help

• HP product information:

http://www.hp.com/go/storage

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

• HP manuals:

http://www.hp.com/support/manuals

Third Edition (September 2007)

Part Number: AA928-96014

*AA928-96014*

AA928-96014

Autres manuels pour ESL E-Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Carte réseau

HP 100TX NightDIRECTOR/100 Manuel utilisateur

HP 3C339 Manuel utilisateur

HP NC510C Manuel utilisateur

HP AD331A Manuel utilisateur

HP D7522A 10/100 3Com 3C905C-TX Manuel utilisateur

HP Rp7410 - Server - 0 MB RAM Manuel d'installation et d'exploitation

HP FlexFabric 10Gb 2-port 534FLR Instructions d'utilisation

HP DA-10852 Manuel utilisateur

HP NC373F Manuel utilisateur

HP Console Management Controller Manuel utilisateur

HP 100B-TX Manuel utilisateur

HP 3C509B-TP Manuel utilisateur

HP 3C905B-TX Manuel utilisateur

HP 441877-00B Manuel utilisateur

HP Q6275A Manuel utilisateur

HP Pro100B Manuel utilisateur

HP External Devices Manuel utilisateur

HP External Media Cards Manuel utilisateur

HP 10BT NightDIRECTOR/100 Manuel utilisateur

HP Ethernet USB Network Adapter hn210e Manuel utilisateur

HP Broadband Service Analyzer Manuel utilisateur

HP StorageWorks e1200-320 4Gb Manuel utilisateur

HP StorageWorks AB232A Manuel utilisateur

HP StorageWorks FC2143 Instructions d'utilisation

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur