HP 100B-TX Manuel utilisateur
Intel EtherExpress PRO 100B-TX
PCI Ethernet Adapter
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
MMXTM is a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
©1999 Hewlett Packard Company
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
1 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 3.51 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 3.51 system that supports NetBEUI, TCP/
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2Connect network cable media to the PRO 100B-TX PCI card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 3.51 Server
9When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
2 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 4.0 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 4.0 system that supports NetBEUI, TCP/IP,
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2Connect network cable media to the PRO 100B-TX PCI card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 4.0 Server
9When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
3 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
NetWare 3.12 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 3.12 system that supports NetBEUI, TCP/IP, NWLink
IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2Connect network cable media to the PRO 100B-TX PCI card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 11
I/O Address 1020 DCE0 E400
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 3.12 Server
9When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
4 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
NetWare 4.11 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 4.11 system that supports NetBEUI, TCP/IP, NWLink
IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2Connect network cable media to the PRO 100B-TX PCI card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 4.11 Server
9When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Autres manuels HP Carte réseau
HP
HP NC373F Manuel utilisateur
HP
HP Pro100B Manuel utilisateur
HP
HP Broadband Service Analyzer Manuel utilisateur
HP
HP 289166-40B Manuel utilisateur
HP
HP hn210w Manuel utilisateur
HP
HP NetMail/3000 Manuel utilisateur
HP
HP 517 Manuel utilisateur
HP
HP FlexFabric 10Gb 2-port 534FLR Instructions d'utilisation
HP
HP 3C509B-TP Manuel utilisateur
HP
HP AB290A Manuel utilisateur
HP
HP D7522A 10/100 3Com 3C905C-TX Manuel utilisateur
HP
HP Ethernet USB Network Adapter hn210e Manuel utilisateur
HP
HP Ethernet USB Network Adapter hn210e Manuel utilisateur
HP
HP ESL E-Series Manuel utilisateur
HP
HP AD331A Manuel utilisateur
HP
HP 3C905B-TX Manuel utilisateur
HP
HP hn210w Manuel utilisateur
HP
HP External Devices Manuel utilisateur
HP
HP UT-300 Manuel utilisateur
HP
HP StorageWorks FC1142SR Instructions d'utilisation
Manuels Carte réseau populaires d'autres marques
3Com
3Com EtherLink 3C509B Manuel utilisateur
TRENDnet
TRENDnet TEG-PCITX Manuel utilisateur
Cisco
Cisco MC16E Manuel utilisateur
Delta Electronics
Delta Electronics Braking Modules VFDB Series Manuel utilisateur
TwinMOS
TwinMOS Booming Manuel utilisateur
Dialogic
Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur
National Instruments
National Instruments NI 9234 Manuel utilisateur
Hama
Hama 49276 Manuel utilisateur
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation
Compaq
Compaq Wireless LAN 100 Manuel utilisateur
Bose
Bose PowerMatch Dante Manuel utilisateur