HP HP 81536A Manuel utilisateur

User's Guide

HP 81536A Sensor Module

SERIAL NUMBERS

This manual applies to all instruments.

ABCDE

HP Part No. 81536-90011

Printed in Germany

Second Edition

E0796

Control Serial Number: Edition 2 applies directly to all instruments.

Edition 1 : 1st May 1990 : 81536-90011 : E0590

1st December 1990 : 81536-90011 : E1290

Edition 2 : 1st April 1992 : 81536-90011 : E0492

1st March 1993 : 81536-90011 : E0393

1st December 1994 : 81536-90011 : E1294

1st July 1996 : 81536-90011 : E0796

Safety Considerations

Before operation, you should review the instrument and manual, including the

red safety page, for safety markings and instructions.You must follow these to

ensure safe operation and to maintain the instrument in safe condition.

Initial Inspection

Warning

To avoid hazardous electrical shock, do not perform

electrical tests when there are signs of shipping damage to

any portion of the outer enclosure (covers, panels, etc.).

Power Requirements

The HP 81536A will operate when installed into the HP 8153A Optical

Multimeter mainframe.

Input/Output Signals

Caution

A maximum of 15V can be applied as an external voltage to any

BNC connectors.

iii

Contents

C. HP 81536A Specications

Supplementary Performance Characteristics . . . . . . . . . . . C-3

Analog output: .... .. .. .. .. .. .. .. .. .. . C-3

D. HP 81536A Performance Tests

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Equipment Required . . . . . . . . . . . . . . . . . . . . . D-1

Test Record .......................... D-2

Test Failure .......................... D-3

Instrument Specication .... .. .. .. .. .. .. .. .. D-3

Performance Test .... .. .. .. .. .. .. .. .. .. . D-3

Accuracy and Linearity Test .... .. .. .. .. .. .. . D-4

Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . D-4

I. Accuracy Test ...................... D-5

II. Linearity Test...................... D-5

III. Noise Test .. .. .. .. .. .. .. .. .. . .. .. . D-7

E. Cleaning Procedures

The Cleaning Kit . . . . . . . . . . . . . . . . . . . . . . . . E-1

Other Cleaning Tools . . . . . . . . . . . . . . . . . . . . . E-3

Preserving Connectors . . . . . . . . . . . . . . . . . . . . . E-4

Cleaning Instrument Housings ................. E-4

Correct Cleaning Procedure .... .. .. .. .. .. .. .. E-5

Cleaning Cable Connectors . . . . . . . . . . . . . . . . . . E-5

Cleaning Connector Adapters . . . . . . . . . . . . . . . . . E-6

Cleaning Connector Interfaces ................ E-6

How to clean instruments with a recessed lens interface . . . . E-7

Light dirt .. .. .. .. .. .. .. .. .. .. . .. .. E-7

Heavy dirt ........................ E-7

Index

Contents-1

Figures

D-1. Accuracy and Linearity Test Setup .............. D-4

D-2. Addition of results (example) . . . . . . . . . . . . . . . . . D-7

Contents-2

HP 81536A Specications

Specications describe the instrument's warranted performance. Supplementary

performance characteristics describe the instrument's non-warranted typical

performance.

Because of the modular nature of the instrument, these performance

specications apply only to this module.You should insert these pages into the

appropriate section of the manual.

HP 81536A Specications C-1

HP 81536A Specications

Sensor Element

InGaAs

Wavelength range

800-1700nm

Power range

+3 to -70dBm

Display resolution

dBm, dB 0.001

0.0001 on printout

Watt 0.01 to 10

(depending on power range)

Applicable ber type

9/125



m - 100/140



m, NA



0.3

Uncertainty (Accuracy)

2.5% (1000-1650nm)

[1]

Total Uncertainty

50pW (1000-1650nm)

[2]

Linearity



Cto28



C const. temp

0.015dB

30pW



Cto55



C const. temp

0.05dB

50pW

Noise

50pW (1200-1600nm)

peak-peak, avg. time 1sec

Dimensions

75mm H, 32mm W, 335mm D (2.8

1.3

13.2

)

Weight

net 0.6kg (1.3lbs), shipping 1kg (2.2lbs)

Recalibration period

2 years

Warmup time

20 min.

The display may vary by

1 count.

Information on the traceability of power meters is available on request

[1] at the following reference conditions:

Power level 10



W (-20dBm), Continuous Wave (CW).

Fiber 50



m graded index, NA=0.2, fully excited.

C-2 HP 81536A Specications

Ambient temperature 23



5K.

Connector Diamond HMS-10/HP.

At day of calibration (add 0.3% for aging over one year, add 0.6% over

two years).

Spectral width of source

10nm.

[2] at the following operating conditions:

Fiber





m, NA



0.2.

For NA

0.2 add 1%.

Ambient temperature 0 to 55



C, non-condensing.

Within 1 year after calibration, add 0.3% for second year.

For Biconic Connector add

1%.

Supplementary Performance Characteristics

Add 1% to total uncertainty for the full wavelength range.

Outside the specied wavelength range, the noise increases by up to 5 times

the value shown above.

Analog output:

Bandwidth:



DC,



300 to 400Hz, depending on range and sensor module.

Output voltage: 0 to 2V into open.

Output impedance: 600 typical.

Max. input voltage:

10V.

HP 81536A Specications C-3

Autres manuels HP Unité de contrôle

HP E3456A Manuel utilisateur

HP E1407A Manuel utilisateur

HP ProCurve Wireless 170wl Manuel utilisateur

HP HPE FlexNetwork 7500 Manuel utilisateur

HP E1364A Manuel utilisateur

HP ProCurve MSM765zl Instructions de montage

HP 900896-121 Mode d’emploi

HP HPE FM 2072 Manuel utilisateur

HP Synergy 480 Gen9 Manuel utilisateur

HP ProCurve PCM+ Agent on ONE zl Module Instructions de montage

HP SIC-4G-LTE-V Manuel utilisateur

HP 70427A Manuel utilisateur

HP StorageWorks MSL6000 series Manuel utilisateur

HP 83481A Manuel utilisateur

HP 98624A Guide de démarrage rapide

HP HP 83491A Manuel utilisateur

HP Synergy 480 Gen10 Manuel utilisateur

HP 16520a Manuel utilisateur

HP R6000 - UPS - Lead Acid Expandable Manuel utilisateur

HP HP E1361A Manuel utilisateur

HP A12500 Instructions de montage

HP JG589A Instructions de montage

HP 83400 Series Manuel utilisateur

HP 83487A Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur