Honeywell ADEMCO 5801 Instructions de montage

N6478V3 5/05 Rev.

ADEMCO 5801

Remote Wireless Panic Transmitte

INSTALLATION AND SETUP GUIDE

GENERAL

The ADEMCO 5801 is a portable unit, which can be programmed (at the control

receiver) to perform up to four system functions (e.g., arm STAY, arm AWAY, Panic,

disarm, etc.). No audible or visual system status indications are provided by the 5801

(except for a Red LED indicator which flashes when the unit transmits). The 5801 is

intended for use only with wireless alarm systems that support 5800 series devices.

The transmitter may be left unmounted, resting on a table, countertop, or other surface,

or carried in a pocket or purse. If the unit will not be wall-mounted, remove the mounting

plate attached to the back of the unit (see step 1 of WALL-MOUNTING instructions on

the other side)

Ensure that a transmission is received from each area where usage of this transmitter is

anticipated.

PROGRAMMING

The 5801 has four unique identification codes permanently assigned during

manufacture. You must “enroll” these codes into the control system at some point prior

to usage of the system. Each button must be enrolled by the control receiver. See

Important Note below.

IMPORTANT PROGRAMMING NOTE: THE 5801 TRANSMITTER MUST BE

PROGRAMMED AS ONE OF THE FOLLOWING INPUT TYPES ONLY:

“UR” type (unsupervised RF) or “RF” type (supervised RF)

The UR type is supervised only for battery status, whereas the RF type is supervised for

an hourly check-in signal and must not be taken out of range of the control receiver.

See the control unit’s Installation Instructions for further details regarding programming.

SELECTION OF FUNCTIONS FOR BUTTONS

For convenience, the 5801 is supplied with the buttons labeled with the functions shown

in Figure 1. Labels for these particular functions were chosen since they are

those likely to be selected for most

installations. However, additional

labels are provided for those cases

where other functions are desired;

simply attach the new label over the

existing one. In all cases, each

button must be programmed for its

desired function, as indicated in the

control unit’s installation instructions.

IMPORTANT NOTE:

If the “Function 4” button is not

used, it MUST be programmed as

a “Not used” zone type.

LED

FUNCTION

STAY

PANIC

OFF

AWAY

FUNCTION

5801-002-V0

Figure 1. 5801 Transmitter

BATTERY INSTALLATION

1. Remove the cover by inserting the

blade of a small screw-driver into

the slot at the bottom of the case

and twisting.

2. Install the Lithium battery supplied

in the battery compart-ment,

observing correct polarity (see

Figure 2). Make sure the battery is

firmly seated.

3. Replace the cover (snap fit).

BATTERY CAUTION;

Risk of fire, explosion and burns. Do

not recharge, disassemble, heat

above 100"C, or incinerate. Dispose

of used batteries promptly. Keep away

from children.

5801-003-V0

LITHIUM

BATTERY

(ADEMCO 466)

Figure 2. 5801 (Cover Removed)

WALL-MOUNTING (OPTIONAL)

To wall-mount the unit, proceed as follows:

1. Disengage the supplied wall mounting plate from the unit by sliding it along the

case back.

2. Attach the mounting bracket in the desired location with the hooks pointing

upward, using the two screws supplied. The word TOP is molded along the upper

edge of the plate.

3. Locate the keyhole slots on the back of the transmitter case onto the bracket’s

hooks, and secure by sliding the case downward, firmly.

SPECIFICATIONS

Size: 4” x 2-1/4” x 13/16”`

102mm x 57mm x 21mm

LED: Flashes when unit transmits.

Battery: 3-volt Lithium. Use only ADEMCO 466, Duracell DL123A,

Panasonic CR123A, Sanyo CR123A.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH WHICH

THIS DEVICE IS USED FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE

LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference (2) This device must accept any

interference received, including interference that may cause undesired operation. The user shall

not make any changes or modifications to the equipment unless authorized by the Installation

Instructions or User's Manual. Unauthorized changes or modifications could void the user's

authority to operate the equipment.

ÊN6478V3ÇŠ

N6478V3 5/05 Rev. B

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Table des matières

Autres manuels Honeywell Émetteur

Honeywell

Honeywell ADEMCO 5878 Instructions de montage

Honeywell

Honeywell ADEMCO 5869 Manuel utilisateur

Honeywell

Honeywell ADEMCO 5804 Instructions de montage

Honeywell

Honeywell XNX Manuel utilisateur

Honeywell

Honeywell XNX-AM Series Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell SMV 3000 Manuel utilisateur

Honeywell

Honeywell 5834-4EN Manuel utilisateur

Honeywell

Honeywell SMV800 Manuel utilisateur

Honeywell

Honeywell 5800MICRA Manuel utilisateur

Honeywell

Honeywell 5817CBXT Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell SmartLine Manuel utilisateur

Honeywell

Honeywell ST 800 Series Mode d’emploi

Honeywell

Honeywell XYR 5000 Series Manuel utilisateur

Honeywell

Honeywell PWTA40 Series Manuel utilisateur

Honeywell

Honeywell KEGS5000 Manuel utilisateur

Honeywell

Honeywell STT25D Manuel utilisateur

Honeywell

Honeywell SmartLine SLG 700 Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell NTC20k Manuel utilisateur

Honeywell

Honeywell 5800MICRA Manuel utilisateur

Honeywell

Honeywell ST 800 Series Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur