Honeywell Midas S2 Manuel utilisateur

Midas® S2

Fixed single-point extractive gas transmitter

Product Description

The Midas® S2 is a Fixed, Extractive Single-Point Gas Transmitter that

draws a sample locally or from a remote point to a sensor cartridge. A wide

range of toxic, flammable and oxygen gas sensor cartridges are available

that enable the detection of gases used or generated in semiconductor

manufacturing operations, light manufacturing environments, and

national and university labs that specialize in semiconductor processing

research.

Features & Benefits:

lHighly modular design for easy, reliable, and trouble-free installation.

lQuick replacement of cartridges and pump parts for simple

maintenance.

lSingle, smart sensor cartridge with onboard * ‘e-calibration’ certificate

l3-built-in relays (Form C) for Alarms 1, 2, and Fault

lSupportive digital communication (Modbus/TCP ethernet/Power over

Ethernet (PoE))

lKeypad interface

lFactory-calibrated sensors to reduce the need for frequent gas testing

l4-20mA analog output with fault and event reporting

lLarge, bright, and rich TFT color LCD and extensive viewing angle.

lmA communication protocols for easy connectivity and service

interaction

lRobust extractive pump system (2-year lifetime) sampling up to 100 feet

lDesigned to ensure maximum uptime while providing a delightful user

experience while using the machine and providing a low cost of

ownership for the customers

lSupportive Digital communication (Modbus / TCP Ethernet / Power over

Ethernet (PoE) )

lBlock test to ensure sampling line connection and no leakage

Safety

CAUTION

RISK OF INJURY AND PROPERTY DAMAGE

lTo minimize the risk of electrostatic charging, provide a suitable

ground connection, and install the equipment in such a way

that no accidental discharges occur.

lWhen Midas S2 reaches the end of its life, it should be disposed

of by local regulations.

lDo not use cleaning solvents or abrasives to clean the gas

detector.

lDo not attempt to modify the product in any way from the

manufacturer’s design or specification. Warranty will be void

and malfunction of the gas detector may result.

lUse only genuine spare parts and accessories with Midas S2.

Malfunction may result if non-standard parts are used.

lMidas® S2 is suitable for ordinary locations only and must not

be installed in hazardous locations.

lInstallation must be by the recognized standards of the

appropriate authority in the country concerned. For Europe, see

EN60079-14, EN60079-29-2, and EN61241-14. For

installations in North America, the National Electrical Code

(NFPA 70) should be strictly observed. All the appropriate local

and national regulations should be observed.

lIndoor use only.

Certifications

Electrical: UL 61010-1,

CSA C22.2 No.61010-1,

IEC 61010-1,

EN 61010-1

ROHS: 3(EU 2015/863)

EMC: EN 50270:2015

What's in a full box System

lMidas® S2 transmitter

lInstallation accessories (tubes, tube adaptor or LIT check valve if

ordered)

lQuick reference guide

lROHS sheet with drill template

Hardware overview

1 Display 2 Pump door latch

3 Navigation buttons 4 Sensor cartridge

5 Sensor release latch 6 Cable gland

7 Mounting holes 8 Pump module

User Interface overview

1 2 3 4

1- Power

LED

2- Alarm 1 3- Alarm 2

4 - Fault 5 - Tips for reset faults or alarms 8- Location label

6 - Buttons

Cancel.

Reset

alarm or

fault

Power on

Down

7 - Device status icons

Network

connected

Network not

connected

Password

enabled

Inhibit mode

is enabled

Flow rate

Internal pump

running

9 - Main status icons

Normal

Alarm 1

Alarm 2

Fault

Inhibit

mode

10- Gas name 11 - Gas concentration 12 - Unit

13 - Bar graph for gas

concentration display

14 - Menu 15 - Information

Specifications

Transmitter Dimension

Size (unit with Cartridge) 138.6 (H) x 55 (W) x 148 (D) mm (5.46 x 2.17 x

5.83 in)

Weight - Transmitter 1.03kg (2.27lb)

Weight - Sensor cartridge 34~73 g (0.075~0.161 lb) dependent on sensor

type

Power Requirements

Operating Voltage 24 VDC Nominal, -15 to +10% (20.4 to 26.4

VDC)

Operating Voltage with Power over

Ethernet (PoE)

48 VDC PoE (IEEE 802.3af compliant)

Power Consumption

Transmitter unit (normal condition) 1Typ. <5W

Transmitter unit (full load condition) 2< 12.95W (with Pyrolyzer)

Outputs

Visuals Power, alarm Fault LEDs and color TFT LCD

Relays Alarm1, Alarm2, Fault relay rated 1.0A@30VDC or

0.5A@125VAC max

Analog Sink/Source, 4-20mA

Digital Communications Modbus/TCP Ethernet/Power over Ethernet (PoE)

Display

Size/color 2.4inch IPS panel with 16.7M display color

Viewing angle 160 or higher degree viewing angle

Operation key 4-button interface keypad

Transport System

Flow Rate 500 mL/min

Sample Line Tubing 3.18mm ID X 6.35mm OD (0.125 X 0.25in)

Sample line Length Up to 30 m (100 ft) with FEP tubing

Exhaust Line Tubing 4.76 mm ID X 6.35 mm OD (0.188 X 0.25 in)

Exhaust Length Up to 30 m (100 ft)

Ambient Point In line air filter required

Environmental

Operating temperature 0°C to +40°C (32°F to 104°F)

0℃to 30℃(32℉to 86℉) with Pyrolyzer

Condition Indoor only

Operating atmospheric pressure 80~120Kpa

Altitude <2000m

Overvoltage Category 1

Pollution degree 2

1Normal condition: (1) No gas alarm, (2) Without tube and pressure/vacuum.

2Full load condition: (1) Gas alarm is on, (2) Maximum tubing length and pressure/vacuum

on the inlet/exhaust line.

Cleaning the system

Clean the exterior of the instrument with a soft, damp cloth. Use only

water-based (non-alcohol) cleaners. Do not use soaps, solvents, or

polishes.

Mount the Device

Mounting the device on a vertical flat surface.

1. Unscrew the two screws located on the main module.

2. Remove the main module by pulling it forwards off the base

module. At this time, hold the cable gland in the base module

with one hand, and with the other hand, carefully pull the main

module.

3. Unscrew the retaining screws located at the base module, and

then, remove the back plane PCB module.

4. Drill two holes 2.3in (58.50mm) vertically apart for 2 x round

head M4 screws, using the separately provided drill template on

the ROHS sheet.

5. Partially screw the fixings into the mounting surface.

6. Place the mounting bracket assembly over the screws, so they

pass through the mounting holes and then slide down to locate

in the slots.

7. Tighten the screws to secure the mounting bracket assembly.

8. Align the RJ45 socket of the power PCB module in the hole of the

mounting bracket to refit the PCB.

9. Tighten the retaining screw to secure the power PCB module.

10. Wire the device as described in the "Wiring" section.

11. Place the main module back into the base module.

12. Screw the two screws located on the main module, as identified

in Step 1.

Autres manuels pour Midas S2

Table des matières

Autres manuels Honeywell Émetteur

Honeywell

Honeywell ST 800 Series Manuel utilisateur

Honeywell

Honeywell NOTIFIER UDACT-2 Manuel utilisateur

Honeywell

Honeywell SMV800 Manuel utilisateur

Honeywell

Honeywell 5834-4EN Manuel utilisateur

Honeywell

Honeywell PEHA FU-BLS Manuel utilisateur

Honeywell

Honeywell SmartLine STIW400 Manuel utilisateur

Honeywell

Honeywell NTC20k Manuel utilisateur

Honeywell

Honeywell ADEMCO 5811 Manuel utilisateur

Honeywell

Honeywell ADEMCO 5878 Instructions de montage

Honeywell

Honeywell PWTA40 Series Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell Satellite XT Manuel utilisateur

Honeywell

Honeywell STT700 SmartLine Mode d’emploi

Honeywell

Honeywell ADEMCO 5805-6 Manuel utilisateur

Honeywell

Honeywell RESCU 406AFN Guide de configuration

Honeywell

Honeywell SmartLine ST700 Manuel utilisateur

Honeywell

Honeywell DACT-E3 Manuel technique

Honeywell

Honeywell 5834 Instructions de montage

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur