Heltun QUINTO HE-TPS05 Manuel utilisateur

TOUCH PANEL SWITCH QUINTO

HE-TPS05 USER MANUAL

V1.0

 
Table of Contents 
Overview ........................................................................................................................................................................... 3 
Technical Specifications.................................................................................................................................................... 3 
Functions & Features ........................................................................................................................................................ 4 
Installation ........................................................................................................................................................................ 5 
Disassembly....................................................................................................................................................................... 6 
Touch Panel Operation ..................................................................................................................................................... 6 
Scenarios........................................................................................................................................................................... 7 
Factory Reset (RES) ........................................................................................................................................................... 7 
Power and Energy Consumption....................................................................................................................................... 7 
Resetting Cumulative Consumption Memory ............................................................................................................. 7 
Z-Wave Network ............................................................................................................................................................... 7 
Adding HE-TPS05 to a Z-Wave network....................................................................................................................... 7 
Removing HE-TPS05 from a Z-Wave network.............................................................................................................. 8 
Security ........................................................................................................................................................................ 8 
SmartStart.................................................................................................................................................................... 8 
Firmware OTA Update ................................................................................................................................................. 8 
Associations ................................................................................................................................................................. 8 
Gateway compatibility requirement.......................................................................................................................... 10 
Z-Wave Plus v2 Specifications.................................................................................................................................... 11 
HE-TPS05 Settings Using Z-Wave Protocol (Gateway)............................................................................................... 11 
Time Configuration............................................................................................................................................... 11 
Sensor Configuration ............................................................................................................................................ 12 
BACKLIGHT............................................................................................................................................................ 13 
Factory Default Parameters.................................................................................................................................. 16 
Limited Warranty............................................................................................................................................................ 17 
 
 
 
 
 
 

Overview

This is the user manual for the HELTUN HE-TPS05 Advanced Programmable Touch Panel Switch. The HE-TPS05

brings ‘Impossibly Smart’ capabilities to your home lighting, electric outlets, or motorized blinds, door locks, gates, and

valves. It replaces an existing in-wall switch and brings over-the-Internet monitoring, control, and advanced

programmability to five connected devices. Quinto is ‘Impossibly Thin’ on the wall yet packed with features to provide

the ultimate in control and convenience.

Controls up to five systems with two different power sources

Thanks to Quinto’s five-channel relays it can manage either: 1) up to five On/Off devices, 2) three On/Off devices and

one bidirectional motor, or 3) one On/Off device and two bidirectional motors. Two independent relay channel inputs

allow control of systems with different power sources or use of relay outputs as dry contacts. Each relay can be

loaded up to 5 Amps.

Connects to Z-Wave lights and dimmers

Quinto is an excellent choice for managing lighting systems. It allows connection to Z-Wave™ lights and dimmers

controlling both On and Off, as well as smooth brighten (Up) and smooth dim (Down) states. Dimmer levels can be

tied to Quinto’s button backlights to provide feedback of connected light state (On/Off).

Controls motorized devices

Quinto can also be used to manage motorized systems like shades/blinds, driveway gates, water valves, or window

and door locks. It also allows association with relay switches to control opening and closing of connected motorized

devices. If door/window sensors are installed, they may be associated with Quinto backlights, enabling them to

indicate device state (Open/Closed).

Touch panel buttons have multiple functions

Quinto has five high sensitivity capacitive touch buttons with two-color backlights (red/blue) for each. 15 backlight

brightness levels can be configured manually or set to automatically adjust to ambient light conditions making them

always easy to see. Each button can be configured to control relay output state (#1-5) in any of nine different modes.

Five ways to trigger programmed scenarios

An onboard Real Time Clock (RTC) enables Quinto to trigger scenarios where connected devices are set to a

schedule. Another powerful feature lets Quinto trigger connected device scenarios when temperature, humidity, or

light sensor values change. Quinto buttons may also directly trigger scenarios on controller —with each backlight

indicating scene status.

Know how much energy you use

Quinto can determine how much energy is used by connected devices any particular day, week, or month. Just

specify the consumption of the load in watts for each relay channel and the device logic will calculate total

consumption relative to the time since the output was in the ‘ON’ state.

Based on the latest Z-Wave platform

Quinto integrates a Z-Wave Plus™ v2 700 platform module allowing it to be used with Z-Wave home automation

systems. It supports Z-Wave ‘S0’ and ‘S2’ security protocols, SmartStart technology, and can be connected

(“associated”) to other Z-Wave devices, such as relays, motor controllers, dimmers, etc.

Technical Specifications

•Front frame (on wall) dimensions: 89mm (H) х89mm (W) х9mm (D)

•Rear electronics package dimensions: 53mm (H) х53mm (W) х28mm (D)

•Materials: Tempered glass display/body, Flame retardant plastic

•5 frame colors: White, Gloss Black, Matte Black, Silver, Chrome

•6 glass colors: White, Black, Yellow, Green, Red, Blue

•5 capacitive-touch buttons

•Red and Blue LED backlights for each button

•15 brightness levels (adjustable) for each button backlight

•5 channel relay outputs, resistive load up to 5A each

•2 independent relays inputs, dry contact

•Operating temperature: 0°Сto +50°С

•Power supply: 85-265VAC 50Hz/60Hz or 24-48VDC

•Power consumption: 1W

•Relay switching with HELTUN Advanced Zero-Cross Technology

•Relay lifetime: 100.000 switches

•Internal ambient light sensor

•Internal temperature sensor

oMeasurement range: –30°C to +80°C

oAccuracy: ±0.5°C

•Internal humidity sensor

oMeasurement range: 0% to 80%RH

oAccuracy: ±3.0%RH

•IP class: IP21

•Z-Wave Plus V2 SDK: V7.11

•Z-Wave module: ZGM130S

•Requires mounting to flush electrical junction box:

round or square type –min. depth 40mm

Functions & Features

•Options for Inclusion/Exclusion to/from Z-Wave network

oNon-Secure

oS0 Secure

oS2 Unauthorized, S2 Authorized with Key

•Association control of 20 devices from the network

•Schedule Mode

•Motorized device control (roller shutter mode)

•Each of five buttons can control any relay output

•Up to five different relay channels can be controlled by one button

•Each button can be set up to control devices from associated groups

•Each button backlight & relay outputs can be managed by a gateway or associated device

•Each button can trigger scenes

•Each button backlight can indicate a scene, or associated device state

•Any channel may be excluded from control

•Nine modes for each button:

1. Switch-ON

2. Switch-OFF

3. Timer: ON>OFF

4. Timer Reversed: OFF>ON

5. Inverse state

6. Two-Button Inverse

7. Momentary

8. Momentary Reversed

9. Roller Shutter

•Adjustable periodic measurements from:

oInternal temperature sensor

oInternal humidity sensor

oInternal ambient light sensor

oEnergy consumption meter

•Calibration of Internal Room Air Temperature Sensor

•Brightness control of button backlight:

oAutomatic adjustment (depending on ambient light)

oManual adjustment (15 levels).

•Backlight standby mode (different brightness for active and inactive states)

•Backlight blinking function (for easy identification among other Z-Wave devices)

•Backlight colors invert

•Software energy consumption logic

•Factory reset function

•SmartStart technology for quick addition to Z-Wave networks

•OTA (Over The Air) encrypted firmware update

Installation

HELTUN recommends the HE-TPS05 touch panel switch be installed by a licensed electrician in

a manner that conforms to local regulations and building codes. Provide these instructions to the

licensed electrician who is installing the HE-TPS05.

WARNING: Electrical power must be switched off during installation.

1. Placement of the HE-TPS05 is of utmost importance for proper operation and must be away

from sunlight and sources of direct heat. We recommend installing the HE-TPS05 approximately

1.5 meters above the floor.

2. Remove the touch panel unit and backplate of the HE-TPS05 from the packaging.

3. FIRST ENSURE THE POWER IS OFF at the main circuit breaker (Fig. 1), and then test the

wires with a probe or multimeter to verify. Insert the power wires to the HE-TPS05 “POWER”

terminal by inserting a small Phillips-head screwdriver in the slot beneath each terminal and

unscrew to open. Follow Fig. 2: Connection Diagram and instructions below:

• Power wires: for AC power (85-265VAC) connect Line & Neutral wires to L & N terminals

labeled “POWER” (Fig 2. left diagram). For DC power (24-48VDC) connect “+” wire to

terminal N and “-” wire to terminal L (Fig 2. right diagram).

• Source 1 wire: connect the required power source for relays 1, 2 and 3 to the terminal labeled “IN 1-3”.

• Source 2 wire: connect the required power source for relays 4 and 5 to the terminal labeled “IN 4-5”.

• Loads: connect the required loads to the relay output terminals labeled “OUT-1”, “OUT-2”, “OUT-3”,

“OUT-4”, “OUT-5”.

Note: HELTUN recommends installing cord terminals (electric wire ferrule) on the ends of wires before connecting

them to the HE-TPS05 outputs (various colors terminals are included in the packaging).

4. Make sure the HE-TPS05 backplate is oriented on the wall with the word “TOP”

pointed upwards. Then secure the backplate onto the electrical junction box using

the four screws provided (do not overtighten). Once the backplate is secured onto

the wall, assemble the HE-TPS05 touch panel unit onto the backplate by first

carefully aligning the two top snap connectors (Fig. 3), and then gently pushing the

entire display unit until it ‘snaps’ into position all the way around.

5. Next, switch ON the main power at the circuit breaker (see photo above). The HE-

TPS05 will start up with original default factory settings (all button backlights will

indicate red).

6. Remove the clear protective film from the touch panel unit by pulling on the top

right-hand tab.

Note: Zero-Cross technology is unavailable if the device operates using DC voltage

(24-48VDC).

Figure 2: Connection Diagrams

Figure 1:

Circuit Breaker

Figure 3: Install

Touch Panel Unit

Disassembly

1. ENSURE POWER IS SWITCHED OFF at the main circuit breaker

AND ALL BUTTON BACKLIGHTS ARE OFF.

2. To remove the HE-TPS05 touch panel unit, grasp firmly at the bottom and pull backwards while tilting

outwards until all tabs disconnect.

3. Remove screws from backplate and disconnect the wires by inserting a small Phillips-head screwdriver into

the slot beneath each wire, then unscrew to release.

Touch Panel Operation

The HE-TPS05 has five relays, five touch buttons and two-color backlights (red and blue) for each button.

1. Each relay can be controlled by any touch button or via a Z-Wave network (using a Z-Wave gateway).

2. Each touch button can be configured to control any relay output state (from one to five) in the modes below:

1) SWITCH-ON: Press button: relay output switches to ON state (i.e. contacts are closed).

2) SWITCH-OFF: Press button: relay output switches to OFF state (i.e. contacts are opened).

3) TIMER: ON>OFF: Press button: relay output switches to ON for the specified time, then reverts to OFF.

(Tip: This function is useful to open/close garage doors, blinds, curtains, etc.)

4) TIMER REVERSED: OFF>ON: Press button: relay output switches to OFF for the specified time then

reverts to ON. (Tip: This function is useful for switching off security systems for a short time.)

Note: Time can be configured from 0 sec to 43200 sec (12 hours).

5) INVERSE STATE: Press button: relay output inverts state: (ON to OFF) or (OFF to ON).

6) TWO-BUTTON INVERSE: When two buttons are in Inverse mode, after pressing a button the

corresponding relay (connected to that button) inverts its state: (from ON to OFF, or from OFF to ON) and the

second relay will be switched OFF.

Note: In this mode both relays cannot be switched ON simultaneously. Can be used for motors direction

control.

7) MOMENTARY: When the button is held the relay output is ON, as soon as the button is released the relay

output state changes to OFF.

8) MOMENTARY REVERSED: When the button is held the relay output is OFF, as soon as the button is

released the relay output state changes to ON.

9) ROLLER SHUTTER: When two relays are connected to the same button, they will operate in ‘roller shutter’

mode. After entering this mode, relays will switch to OFF state, and never switch ON simultaneously. The

relay behavior is as follows for this four-touch cycle (in this order):

•1st press: first relay will be switched ON, second relay will be switched OFF

•2nd press: both relays will be switched OFF

•3rd press: second relay will be switched ON, first relay will be switched OFF

•4th press: both relays will be switched OFF

The above mentioned two relays are defined according to parameters 40 & 41 (e.g. if “54” is set as the

parameter value, it means the fifth relay and fourth relay will be operated in inverse mode).

Note: This can be used to control motor directions with one button only.

Each touch button can also be used to run scenarios or change modes in the connected gateway or associated devices.

3. Each button’s backlight can be configured as follows to indicate:

a) Relay output state

b) Touch button state

c) Mode state in connected gateway

d) Associated device state

Note: It is possible to choose the light color for each state (red for ON and blue for OFF, or blue for ON and red for

OFF).

If the HE-TPS05 is associated with a Z-Wave gateway, the scene controller, light, temperature & humidity sensor info,

and ten binary switches will appear. The scene controller indicates which button was pressed, held, or released and

allows the running of scenes on the Z-Wave gateway. The first five binary switches indicate, and allow the control of,

the button backlights. The remaining five binary switches indicate and control the relay outputs.

Scenarios

Scenarios can be created that allow connected devices to be triggered by a sensor or onboard Real Time Clock

(RTC). The HE-TPS05 has built-in temperature, humidity, and ambient temperature sensors and includes a very

flexible, user-friendly interface for customizing scenarios. In addition to the physical sensors, time may be used as a

control source. The user should configure the output number, state, sensor type, state change condition, and

threshold in the Parameters (from 42 - 51) which will trigger the scenes.

Factory Reset (RES)

To reset the HE-TPS05 to factory defaults, simultaneously press the two bottom buttons and hold for six seconds. If

the reset process is successful, all visible LEDs will turn Off.

NOTE: This factory reset procedure will change all parameters to the original factory default values and will also

exclude the device from any associated Z-Wave network.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Power and Energy Consumption

The HE-TPS05 monitors all connected loads active (i.e. ‘real time’) power, and total energy consumption, through

software energy consumption logic. This data is periodically reported to the main Z-Wave controller according to

Parameter 05.

Total Energy Consumption is the electrical power being used by connected device in real time during use. Power

usage is calculated by the software using the values that were manually set when configuring Parameters 52-56,

multiplied by the time tracked when the HE-TPS05 corresponding output was in an ON state. Using your connected

device’s power consumption specification (see associated owner’s manual), set the load in Watts for: “OUT-1” in

Parameters 52, “OUT-2” in Parameter 53, “OUT-3” in Parameter 54, “OUT-4” in the Parameter 55, and “OUT-5” in

Parameter 56.

Resetting Cumulative Consumption Memory

The HE-TPS05 enables you to erase stored consumption data through the Z-Wave network as follows:

1. Make sure the HE-TPS05 is powered.

2. If not already done so, include the device into Z-Wave Gateway network

3. Reset memory consumption data using the Reset Command in COMMAND_CLASS_METER (see the Gateway

owner’s manual).

Note: Power cycling the HE-TPS05 (On>Off>On) will not erase the consumption data as it is stored in non-volatile

memory.

Z-Wave Network

The HE-TPS05 may be operated in any Z-Wave network with other Z-Wave-certified devices from other

manufacturers. The HELTUN HE-TPS05 will act as a ‘repeater’ (i.e. ‘range extender’) for other devices regardless of

manufacturer or brand to increase the reliability of the overall network.

Adding HE-TPS05 to a Z-Wave network

To add the HE-TPS05 to a Z-Wave Network (i.e. “inclusion”), do the following:

1. Start the inclusion mode from the gateway / controller

2. To start the inclusion process on the HE-TPS05, simultaneously press the two bottom touch buttons and hold them

for three seconds.

3. The two upper buttons will then sequentially blink ‘blue-red’

4. If the inclusion has been successful, the two upper buttons will turn blue for three seconds.

5. If the inclusion was not successful, the two upper buttons will turn red for three seconds. In that case repeat the

inclusion process.

Note: For correct operating in Fibaro gateways the Single Channel Association should be removed from the device

LifeLine (EndPoint 0 Group 1).

Removing HE-TPS05 from a Z-Wave network

To remove the HE-TPS05 from a Z-Wave Network (i.e. “exclusion”), do the following:

1. Start the exclusion mode from the gateway/controller.

2. To start the exclusion process on the HE-TPS05, simultaneously press the two bottom touch buttons and hold

them for three seconds.

3. Two upper buttons will sequentially blink blue-red.

4. If the exclusion has been successful, the two upper buttons will turn red for three seconds.

5. If the exclusion was not successful, the two upper buttons will turn blue for three seconds. In that case repeat the

exclusion process.

Note: If the HE-TPS05 has previously been part of a Z-Wave network and has not been excluded since, inclusion is

not possible without first performing an exclusion or Factory Reset procedure.

Security

S0, S2 unauthorized, and S2 authorized Inclusion Modes are supported. If you use the S2 authorized Inclusion mode,

the ‘security key’ (DSK provided on the HE-TPS05 Security Card) should be used during the inclusion process.

Note: Be sure to save this key. Without the key, it is impossible to perform an inclusion in S2 authorized mode.

SmartStart

SmartStart-enabled products can be added to a Z-Wave network by

scanning the Z-Wave QR Code shown on the product with

gateways/controllers that allow for SmartStart inclusion. In this case,

no further action will be required and the SmartStart product will be

added automatically within ten minutes of being turned on in the

vicinity of a network.

To add the HE-TPS05 to a Z-Wave network using SmartStart:

1. Input the HE-TPS05 DSK code to the controller's Node

Provisioning List

2. Power on the device.

3. Wait for the inclusion process to complete.

4. A successful “Add” will be confirmed by a message on the Z-Wave

controller.

Note: The device DSK and QR code are printed on the HE-TPS05

back panel plus on the additional Security Card included in the HE-

TPS05 packaging.

Firmware OTA Update

To wirelessly update the HE-TPS05 firmware, follow these steps:

1. Check the device current firmware version in the gateway/controller.

2. Start the process from the Z-Wave gateway/controller.

3. Download the latest firmware that corresponds to the HE-TPS05 (see https://www.heltun.com/support )

4. Set the main controller in Firmware OTA (“over-the-air”) Update Mode (see the gateway/controller manual).

5. As soon as the Firmware update begins, all buttons will sequentially blink blue-red (this will take a few minutes).

6. When the Firmware has updated, all button backlights will turn off for two seconds and the HE-TPS05 will reboot.

7. When the update has been completed, the HE-TPS05 will return to normal operation.

8. If desired, verify the update was successful by checking firmware version from the gateway/controller.

Associations

Association enables the HE-TPS05 to control up to 20 other Z-Wave devices over the network. The HE-TPS05 has 11

Endpoints and 21 Association Groups. Each Association Group (except group 1) may include one other device from

different brands and/or manufacturers.

Figure 4: Security Code & QR Code

EndPoint 0 Groups:

The Root Device (EndPoint 0) of HE-TPS05 has 21 association groups

Group 1 –“Lifeline”: reports state of the device and is used to communicate with the Z-Wave gateway. This group

supports one Node.

Note: It is not recommended to modify this group.

Note: For correct operating in Fibaro gateways the Single Channel Association should be removed from the device

LifeLine (EndPoint 0 Group 1).

Group 2 –“Touch 1 Basic Set”: is assigned to touch N1. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 3 –“Touch 1 Multilevel Set”: is assigned to touch N1. It sends MULTILEVEL SWITCH command class frame

when touch N1 was held. Is used to send UP/DOWN command to the associated devices. The group supports one

Node.

Group 4 –“Touch 2 Basic Set”: is assigned to touch N2. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 5 –“Touch 2 Multilevel Set”: is assigned to touch N2. It sends MULTILEVEL SWITCH command class frame

when touch N2 was held. Is used to send UP/DOWN command to the associated devices. The group supports one

Node.

Group 6 –“Touch 3 Basic Set”: is assigned to touch N3. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 7 –“Touch 3 Multilevel Set”: is assigned to touch N3. It sends MULTILEVEL SWITCH command class frame

when touch N3 was held. Is used to send UP/DOWN command to the associated devices. The group supports one

Node.

Group 8 –“Touch 4 Basic Set”: is assigned to touch N4. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 9 –“Touch 4 Multilevel Set”: is assigned to touch N4. It sends MULTILEVEL SWITCH command class frame

when touch N4 was held. Is used to send UP/DOWN command to the associated devices. The group supports one

Node.

Group 10 –“Touch 5 Basic Set”: is assigned to touch N5. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 11 –“Touch 5 Multilevel Set”: is assigned to touch N5. It sends MULTILEVEL SWITCH command class

frame when touch N5 was held. Is used to send UP/DOWN command to the associated devices. The group supports

one Node.

Group 12 –“LED 1 Basic Set”: is assigned to LED N1. Is used to send Basic Set ON (value 255) and Basic Set OFF

(value 0) commands to the associated devices. The group supports one Node.

Group 13 –“LED 2 Basic Set”: is assigned to led N2. Is used to send Basic Set ON (value 255) and Basic Set OFF

(value 0) commands to the associated devices. The group supports one Node.

Group 14 –“LED 3 Basic Set”: is assigned to led N3. Is used to send Basic Set ON (value 255) and Basic Set OFF

(value 0) commands to the associated devices. The group supports one Node.

Group 15 –“LED 4 Basic Set”: is assigned to led N4. Is used to send Basic Set ON (value 255) and Basic Set OFF

(value 0) commands to the associated devices. The group supports one Node.

Group 16 –“LED 5 Basic Set”: is assigned to led N5. Is used to send Basic Set ON (value 255) and Basic Set OFF

(value 0) commands to the associated devices. The group supports one Node.

Group 17 –“Relay 1 Basic Set”: is assigned to relay N1. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 18 –“Relay 2 Basic Set”: is assigned to relay N2. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 19 –“Relay 3 Basic Set”: is assigned to relay N3. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 20 –“Relay 4 Basic Set”: is assigned to relay N4. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

Group 21 –“Relay 5 Basic Set”: is assigned to relay N5. Is used to send Basic Set ON (value 255) and Basic Set

OFF (value 0) commands to the associated devices. The group supports one Node.

EndPoints 1-10 Groups:

Group 1 –“Lifeline”: reports state of the device and used to communicate with the Z-Wave gateway. The group

supports one Node.

Note: It is not recommended to modify this group.

Group 2 –“Basic Set”: Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the

associated devices. The group supports one Node and it is mapped to EndPoint 0 groups.

Here is a truth table for EndPoints 1-10 groups mapping to root device (EndPoint 0) groups:

EndPoints 1-10 groups

Root (EndPoint 0) groups

Endpoint 1, Group 2 –“LED 1 Basic Set”

Group 12 –“LED 1 Basic Set”

Endpoint 2, Group 2 –“LED 2 Basic Set”

Group 13 –“LED 2 Basic Set”

Endpoint 3, Group 2 –“LED 3 Basic Set”

Group 14 –“LED 3 Basic Set”

Endpoint 4, Group 2 –“LED 4 Basic Set”

Group 15 –“LED 4 Basic Set”

Endpoint 5, Group 2 –“LED 5 Basic Set”

Group 16 –“LED 5 Basic Set”

Endpoint 6, Group 2 –“Relay 1 Basic Set”

Group 17 –“Relay 1 Basic Set”

Endpoint 7, Group 2 –“Relay 2 Basic Set”

Group 18 –“Relay 2 Basic Set”

Endpoint 8, Group 2 –“Relay 3 Basic Set”

Group 19 –“Relay 3 Basic Set”

Endpoint 9, Group 2 –“Relay 4 Basic Set”

Group 20 –“Relay 4 Basic Set”

Endpoint 10, Group 2 –“Relay 5 Basic Set”

Group 21 –“Relay 5 Basic Set”

Gateway compatibility requirement

In order to make a reliable connection and data exchange with the gateway make sure that the Gateway/controller is

multi-channel capable. The gateway/controller lifeline association should be configured as a “multi-channel

association.” Some Gateways need this option to be manually configured.

Note: Fibaro Home Center 2: In order to enable correct communications between a Fibaro Gateway/Controller and

the HE-TPS05, the lifeline association should be configured as a “multi-channel association.” Make sure that only the

Multi-channel association check box is selected under Device > Settings > Advanced > Setting Association > Group1

tab (lifeline).

Note: By default, there are two checkboxes for Single-channel and Multi-channel associations. Please deselect the

checkbox under Single-channel associations.

Autres manuels pour QUINTO HE-TPS05

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Heltun Changer

Heltun

Heltun HE-TPS01 Manuel utilisateur

Heltun

Heltun HE-TPS01 Manuel utilisateur

Heltun

Heltun QUINTO HE-RS01 Manuel utilisateur

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun HE-TPS02 Manuel utilisateur

Heltun

Heltun QUINTO HE-RS01 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur