Heltun QUINTO HE-RS01 Manuel utilisateur

RELAY SWITCH QUINTO

HE-RS01 USER MANUAL

for Hardware v.76 & Firmware v.1.2

Table of Contents

Overview ........................................................................................................................................................................... 3

Technical Specifications ................................................................................................................................................... 3

Functions & Features ....................................................................................................................................................... 4

Installation ........................................................................................................................................................................ 4

Disassembly ..................................................................................................................................................................... 5

Factory Reset (RES) ........................................................................................................................................................ 5

Z-Wave Network ............................................................................................................................................................... 5

Adding HE-RS01 to a Z-Wave network ....................................................................................................................... 5

Removing HE-RS01 from a Z-Wave network .............................................................................................................. 6

Security ....................................................................................................................................................................... 6

SmartStart ................................................................................................................................................................... 6

Firmware OTA Update ................................................................................................................................................ 6

Z-Wave Plus v2 Specifications .................................................................................................................................... 7

Associations ................................................................................................................................................................ 7

Gateway Compatibility Requirement ........................................................................................................................... 8

Operation .......................................................................................................................................................................... 9

Scenarios .......................................................................................................................................................................... 9

Power and Energy Consumption ...................................................................................................................................... 9

Settings (available through Z-Wave network) ............................................................................................................... 10

Parameters List & Factory Defaults ........................................................................................................................... 10

Z-Wave Frequency .................................................................................................................................................... 12

Hardware & Software Versions ................................................................................................................................. 13

Power and Energy Consumption ............................................................................................................................... 13

Outputs NO/NC Mode ............................................................................................................................................... 13

Time Configurations .................................................................................................................................................. 13

Buttons Mode ............................................................................................................................................................ 14

Relays Mode ............................................................................................................................................................. 14

Scenarios .................................................................................................................................................................. 15

Energy Report Interval .............................................................................................................................................. 15

Association Commands Configuration ...................................................................................................................... 15

Limited Warranty ............................................................................................................................................................ 17

Overview

This is the user manual for the HELTUN HE-RS01 Advanced Programmable Relay Switch ‘Quinto’ (i.e. five-channel). It

is designed to fit inside standard round, square, or rectangular electrical junction boxes installed behind an existing in-

wall switch or inside a circuit breaker panel. Relay Switch Quinto enables On/Off controls of lights, dimmers, blinds,

doors, gates, valves, and motors either manually by a direct-connected switch, or remotely through a Z-Wave™ network.

Thanks to the HE-RS01 five-channel relays it can manage up to five On/Off devices, or three On/Off devices and one

two-direction motors, or one On/Off device and two two-direction motors. It has two independent inputs for relay

channels which allow it to control systems with different power sources or to use relay outputs as dry contacts. Each

relay can be loaded up to five amps and uses the HELTUN Advanced Zero-Cross Technology to increase the life of the

device and connected system.

The HE-RS01 can also be used to manage motorized systems, e.g. garage doors, window blinds, etc. It allows

association with relay switches and roller shutters to control the opening and closing of the system.

The HE-RS01 has an onboard Real Time Clock (RTC) that enables scenarios where connected devices can be triggered

on a schedule.

The HE-RS01 has five fully configurable inputs for external switches. Each input can be configured to control the relay

output state (from one to five) in any of ten different modes. The inputs also can be used to activate scenes on a Z-

Wave Controller.

The HE-RS01 integrates a Z-Wave Plus™ v2 700 platform module allowing it to be used with Z-Wave home automation

systems. It supports Z-Wave ‘S0’ and ‘S2’ security protocols, SmartStart technology, and can be connected (i.e.

“associated”) with up to 75 other Z-Wave devices, such as relays, switches, dimmers, motor controllers, etc.

The HE-RS01 is also an excellent choice for managing lighting systems, allowing association to Z-Wave dimmers

controlling both On and Off—as well as smooth brighten (Up) and smooth dim (Down)—states using external switches

connected to HE-RS01 inputs.

Technical Specifications

• Dimensions: 50mm (H) х 50mm (W) х 27mm (D)

• Materials: Flame retardant plastic

• LED indicator for device status

• Five-channel relay outputs, resistive load up to 5A each

• Two independent relays inputs, dry contact

• Operating temperature: 0°С to 50°С

• Power supply: 85-265VAC 50Hz/60Hz, or 24-48VDC

• Power consumption: 1W

• Active elements: Electromagnetic Relay Switch

• HELTUN Advanced Zero-Cross relay switching technology

• Relay life: 100.000 switches

• Device control

o Through Z-Wave network

o Directly with pilot wires

• IP class: IP21

• Z-Wave Plus V2 SDK: V7.11

• Z-Wave module: ZGM130S

• Requires mounting to flush electrical junction box:

round, square, or rectangular type – min. depth 40mm

Functions & Features

• Options for Inclusion/Exclusion to/from Z-Wave network

o Non-Secure

o S0 Secure

o S2 Unauthorized, S2 Authorized with Key

• Association control of Z-Wave devices in the network

• Schedule mode

• Motorized device control (roller shutter mode)

• Each of five external inputs can control any relay output

• Up to five different relay channels can be controlled by one external input

• Each external input can be set up to control devices from associated groups

• Each external input & relay output can be managed by a gateway or associated device

• Each external input can trigger scenes (i.e. acts like scene controller)

• Any relay channel may be excluded from control

• Ten modes for each external input:

1. Momentary

2. Momentary Reversed

3. Momentary Toggle

4. Toggle

5. Switch ON Only

6. Switch OFF Only

7. Timer (ON to OFF)

8. Timer Reversed (OFF to ON)

9. Two-Relay Inverse

10. Roller Shutter

• Adjustable periodic measurements from:

o Energy consumption meter

• LED blinking function (for easy identification among other Z-Wave devices)

• Software energy consumption logic

• Factory reset function

• SmartStart technology for quick addition to Z-Wave networks

• OTA (Over The Air) encrypted firmware update

Installation

HELTUN recommends the HE-RS01 relay switch be installed by a licensed electrician in a manner that conforms to

local regulations and building codes. Provide these instructions to the licensed electrician who is installing the HE-RS01.

WARNING: Electrical power must be switched off during installation.

1. FIRST ENSURE THE POWER IS OFF at the main circuit breaker, and then test the wires with a

probe or multimeter to verify.

2. Insert power wires into the HE-RS01 “POWER” terminals by inserting a small Phillips-head

screwdriver in the slot beneath each terminal and unscrew to open. Follow Fig. 2: Connection

Diagram and instructions below:

• Power wires: for AC power (85-265VAC) connect Line & Neutral wires to L & N terminals

labeled “POWER”. For DC power (24-48VDC) connect “+” wire to terminal L and “–” wire to

terminal N.

• Source 1 wire: connect the required power source for relays 1, 2, and 3 to the terminal

labeled “IN 1-3”.

• Source 2 wire: connect the required power source for relays 4 and 5 to the terminal labeled

“IN 4-5”.

• Loads: connect the required loads to the relay output terminals labeled “OUT-1”, “OUT-2”,

“OUT-3”, “OUT-4”, “OUT-5”.

Note: HELTUN recommends installing cord terminals (electric wire ferrules) on the ends of wires before connecting

them to the HE-RS01 outputs (various colors terminals are included in the packaging).

Note: Zero-Cross technology is unavailable if the device operates using DC voltage (24-48VDC).

Figure 1:

Circuit Breaker

Figure 2: Power, Loads & External Switches Connection Diagram

3. Next, connect terminals S1, S2, S3, S4, S5 to external control keys (switches) following Fig. 2 left diagram or

Fig. 2 right diagram.

Note: In case of using Figure 2 right diagram, it is MANDATORY to connect external switches to the same wire

connected to terminal L on the device.

4. Switch on the main power at the circuit breaker. The HE-RS01 will start up with original default factory settings

and the LED indicator will blink red slowly meaning the device is excluded from a Z-Wave network.

Disassembly

1. ENSURE POWER IS SWITCHED OFF at the main circuit breaker AND THE LED INDICATOR IS OFF.

2. Disconnect the wires by inserting a small Phillips-head screwdriver into the slot beneath of each wire and turning

counter-clockwise to release.

Factory Reset

To reset the HE-RS01 to factory defaults, press and hold the service button for six seconds. If successful, the LED

indicator will blink white slowly for two seconds, then the device will reboot.

This factory reset procedure will change all parameters to the original factory default values and will also exclude the

device from any associated Z-Wave network.

Note: Please use Factory Reset only when the primary network controller is missing or otherwise inoperable.

Z-Wave Network

The HE-RS01 may be operated in any Z-Wave network with other Z-Wave-certified devices from other manufacturers.

The HELTUN HE-RS01 will act as a ‘repeater’ (i.e. ‘range extender’) for other devices regardless of manufacturer or

brand to increase the reliability of the overall network.

Adding to Z-Wave network

To add the HE-RS01 to a Z-Wave Network (i.e. “Inclusion”), do the following:

1. Ensure the HE-RS01 is Powered On and the LED indicator blinks red slowly (i.e. it is excluded)

2. Start the Inclusion mode from the gateway/controller

3. To start the inclusion process on the HE-RS01, double-press the service button on the device (with no more than a

one-second interval between presses).

4. The LED indicator will blink green quickly.

5. If the inclusion has been successful, the LED indicator will turn green for three seconds then continue slowly blinking

green continuously while the HE-RS01 is Powered On.

6. If the inclusion was not successful, the LED indicator will turn red for three seconds then continue slowly blinking red

continuously while Powered On. In that case repeat the inclusion process (steps 2-5) above.

Removing from Z-Wave network

To remove the HE-RS01 from a Z-Wave Network (i.e. “Exclusion”), do the following:

1. Ensure the HE-RS01 is Powered On and the LED indicator is slowly blinking green (i.e. it is included in a Z-Wave

network).

2. Start the Exclusion mode from the gateway/controller.

3. To start the exclusion process on the HE-RS01, double-press the service button on the device (with no more than a

one-second interval between presses).

4. The LED indicator will blink red quickly.

5. If the inclusion has been successful, the LED indicator will turn red for three seconds then continue blinking red slowly

continuously while the HE-RS01 is Powered On.

6. If the inclusion was not successful, the LED indicator will turn green for three seconds then continue slow blink green

all the time the device is Powered On. In that case repeat the exclusion process (steps 2-5) above.

Note: If the HE-RS01 has previously been part of a Z-Wave network and has not been Excluded since (the LED indicator

blinks green slowly), inclusion is not possible without first performing an Exclusion or Factory Reset procedure.

Security

S0, S2 unauthorized, and S2 authorized Inclusion Modes are supported. If you use the S2 authorized Inclusion Mode,

the security key should be used during the inclusion process. Security key is the first 5 digits of DSK (device DSK is

printed on the rear of the device plus on the Security Card included in the packaging).

Note: Be sure to save this key. Without the key, it is impossible to perform an inclusion in S2 authorized mode.

SmartStart

SmartStart-enabled products can be added to a Z-Wave network by scanning the

Z-Wave QR Code shown on the product (see Fig. 3) with gateways/controllers that allow for

SmartStart inclusion. In this case, no further action will be required and

the SmartStart product will be added automatically within ten minutes of being

turned on in the vicinity of a network.

To add the HE-RS01 to a Z-Wave network using SmartStart:

1. Input the HE-RS01 DSK code to the controller's Node Provisioning List (or scan the QR

code).

2. Power on the device.

3. Wait for the inclusion process to complete.

4. Successful adding will be confirmed by a message on the Z-Wave controller (depending

on the controller type) and the LED indicator on HE-RS01 will turn green for three seconds

then continue to slowly blink green continuously while the device is Powered On.

Note: The device QR code and DSK are printed on the front and rear of the HE-RS01 plus

on the Security Card included in the HE-RS01 packaging.

Firmware OTA Update

To wirelessly update the HE-RS01 firmware, follow these steps:

1. Check the device current firmware version in the gateway/controller.

2. Start the process from the Z-Wave gateway/controller.

3. Download the latest firmware that corresponds to the HE-RS01 (see https://support.heltun.com/ )

4. Set the main controller in Firmware OTA (“over-the-air”) Update Mode (see the gateway/controller manual).

5. As soon as the Firmware update begins, the LED indicator will sequentially blink red→green→blue (this will take a

few minutes).

6. When the Firmware has updated, the LED will turn blue for two seconds and then the HE-RS01 will reboot.

7. When the update has been completed, the HE-RS01 will return to normal operation.

8. If desired, verify the update was successful by checking firmware version from the gateway/controller.

Figure 3: SmartStart

QR Code & DSK

Z-Wave Plus v2 Specifications

Generic Device Class: GENERIC_TYPE_WALL_CONTROLLER

Specific Device Class: SPECIFIC_TYPE_NOT_USED

Supported Command Classes

Command Class

Version

Required Security Class

Z-Wave Plus Info

none

Association

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Association Group Info

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Multi Channel Association

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Multi Channel

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Switch Binary

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Central Scene

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Meter

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Clock

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Transport Service

none

Security 0

none

Security 2

none

Version

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Manufacturer Specific

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Device Reset Locally

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Powerlevel

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Supervision

none

Indicator

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Configuration

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Application Status

none

Firmware Update Meta Data

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Basic

highest granted (S2 Authenticated, S2 Unauthenticated or S0)

Meter Command Class:

Meter Type

Scale

Rate Type

Precision

Size

Electric [0x01]

Electric_kWh [0x00]

Import [0x01]

Electric [0x01]

Electric_W [0x02]

Import [0x01]

Associations

Association enables the HE-RS01 to control other Z-Wave devices over the network. The HE-RS01 has 6 Endpoints

and 16 Association Groups. Each Association Group (except group 1) may include five other devices from different

brands and/or manufacturers.

EndPoint 0 Groups:

The Root Device (EndPoint 0) of HE-RS01 has 16 association groups:

Group 1 – “Lifeline”: reports full state of the device and is used to communicate with the Z-Wave gateway. The group

supports one Node.

Note: It is not recommended to modify this group.

Note: For correct operating in Fibaro gateways, the Single Channel Association should be removed from the device

LifeLine (EndPoint 0 Group 1).

Group 2 – “External Input S1 Basic Set”: is assigned to the state of S1 input and will be triggered when the button is

pressed on the switch connected to input S1. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0)

commands to the associated devices. The group supports five Nodes.

Group 3 – “External Input S1 Multilevel Set”: is assigned to the state of S1 input. It sends MULTILEVEL SWITCH

command class frame when the button is held on the switch connected to input S1. Is used to send UP/DOWN command

to the associated devices. The group supports five Nodes.

Group 4 – “External Input S2 Basic Set”: is assigned to the state of S2 input and will be triggered when the button is

pressed on the switch connected to input S2. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0)

commands to the associated devices. The group supports five Nodes.

Group 5 – “External Input S2 Multilevel Set”: is assigned to the state of S2 input. It sends MULTILEVEL SWITCH

command class frame when the button is held on the switch connected to input S2. Is used to send UP/DOWN command

to the associated devices. The group supports five Nodes.

Group 6 – “External Input S3 Basic Set”: is assigned to the state of S3 input and will be triggered when the button is

pressed on the switch connected to input S3. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0)

commands to the associated devices. The group supports five Nodes.

Group 7 – “External Input S3 Multilevel Set”: is assigned to the state of S3 input. It sends MULTILEVEL SWITCH

command class frame when the button is held on the switch connected to input S3. Is used to send UP/DOWN command

to the associated devices. The group supports five Nodes.

Group 8 – “External Input S4 Basic Set”: is assigned to the state of S4 input and will be triggered when the button is

pressed on the switch connected to input S4. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0)

commands to the associated devices. The group supports five Nodes.

Group 9 – “External Input S4 Multilevel Set”: is assigned to the state of S4 input. It sends MULTILEVEL SWITCH

command class frame when the button is held on the switch connected to input S4. Is used to send UP/DOWN command

to the associated devices. The group supports five Nodes.

Group 10 – “External Input S5 Basic Set”: is assigned to the state of S5 input and will be triggered when the button

is pressed on the switch connected to input S5. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0)

commands to the associated devices. The group supports five Nodes.

Group 11 – “External Input S5 Multilevel Set”: is assigned to the state of S5 input. It sends MULTILEVEL SWITCH

command class frame when the button is held on the switch connected to input S5. Is used to send UP/DOWN command

to the associated devices. The group supports five Nodes.

Group 12 – “Relay 1 Basic Set”: is assigned to the state of relay N1 and will be triggered on the relay state change.

Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices. The group

supports five Nodes.

Group 13 – “Relay 2 Basic Set”: is assigned to the state of relay N2 and will be triggered on the relay state change.

Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices. The group

supports five Nodes.

Group 14 – “Relay 3 Basic Set”: is assigned to the state of relay N3 and will be triggered on the relay state change.

Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices. The group

supports five Nodes.

Group 15 – “Relay 4 Basic Set”: is assigned to the state of relay N4 and will be triggered on the relay state change.

Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices. The group

supports five Nodes.

Group 16 – “Relay 5 Basic Set”: is assigned to the state of relay N5 and will be triggered on the relay state change.

Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices. The group

supports five Nodes.

EndPoints 1-5 Groups:

Group 1 – “Lifeline”: reports state of the device and used to communicate with the Z-Wave gateway. The group supports

one Node.

Note: It is not recommended to modify this group.

Group 2 – “Basic Set”: Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the

associated devices. Each group supports five Nodes and it is mapped to EndPoint 0 groups.

Here is a truth table for EndPoints 1-5 groups mapping to the root device (EndPoint 0) groups:

EndPoints 1-10 groups

Root (EndPoint 0) groups

Endpoint 1, Group 2 – “Relay 1 Basic Set”

Group 12 – “Relay 1 Basic Set”

Endpoint 2, Group 2 – “Relay 2 Basic Set”

Group 13 – “Relay 2 Basic Set”

Endpoint 3, Group 2 – “Relay 3 Basic Set”

Group 14 – “Relay 3 Basic Set”

Endpoint 4, Group 2 – “Relay 4 Basic Set”

Group 15 – “Relay 4 Basic Set”

Endpoint 5, Group 2 – “Relay 5 Basic Set”

Group 16 – “Relay 5 Basic Set”

Gateway compatibility requirement:

In order to make a reliable connection and data exchange with the gateway make sure that the gateway/controller is

multi-channel capable. The gateway/controller lifeline association should be configured as a “multi-channel association.”

Some Gateways need this option to be manually configured.

Note: Fibaro Home Center 2: In order to enable correct communications between a Fibaro Gateway/Controller and

the HE-RS01, the lifeline association should be configured as a “multi-channel association.” Make sure that only the

Multi-channel association check box is selected under Device > Settings > Advanced > Setting Association > Group1

tab (lifeline). By default, there are two checkboxes for Single-channel and Multi-channel associations. Please deselect

the checkbox under Single-channel associations.

Operation

The HE-RS01 has five relays and five external inputs (S1, S2, S3, S4, S5).

1. Each relay can be controlled by any external input or via a Z-Wave network (using a Z-Wave gateway).

2. Each external input can be configured to control any relay output state (from one to five) in the modes below:

1) MOMENTARY (factory default mode): When the button on an external switch is held, the relay output turns ON.

As soon as the button is released, the relay output state changes to OFF (see Parameters 41-45 settings).

2) MOMENTARY REVERSED: When the button on an external switch is held, the relay output turns OFF. As soon

as the button is released, the relay output state changes to ON (see Parameters 41-45 settings).

3) MOMENTARY TOGGLE: When the button on an external switch is held, the relay output inverts state (from ON

to OFF or from OFF to ON), as soon as the button is released the relay output inverts state again (see

Parameters 41-45 settings).

4) TOGGLE: Press button on external switch: relay output inverts state: (ON to OFF) or (OFF to ON).

5) SWITCH ON ONLY: Press button on external switch: relay output switches to ON state

(i.e. contacts are closed).

6) SWITCH-OFF: Press button on external switch: relay output switches to OFF state

(i.e. contacts are opened).

7) TIMER: ON>OFF: Press button on external switch: relay output switches to ON for the specified time, then

reverts to OFF. (Tip: This function is useful to open/close garage doors, blinds, curtains, etc.)

8) TIMER REVERSED: OFF>ON: Press button on external switch: relay output switches to OFF for the specified

time then reverts to ON. (Tip: This function is useful for switching off security systems for a short time.)

Note: Time can be configured from 0 to 12 hours (0 to 43200 seconds).

9) TWO-RELAY INVERSE: When two relays are in Inverse mode, after pressing a button on external switch the

corresponding relay (connected to that button) inverts its state: (from ON to OFF, or from OFF to ON) and the

second relay will be switched OFF.

Note: In this mode both relays cannot be switched ON simultaneously. Can be used for motor direction control.

10) ROLLER SHUTTER: When two relays are connected to the same external switch, they will operate in ‘roller

shutter’ mode. After entering this mode, relays will switch to OFF state, and never switch ON simultaneously.

The four-cycle relay behavior is as follows (in this order):

• 1st press: first relay will be switched ON, second relay will be switched OFF

• 2nd press: both relays will be switched OFF

• 3rd press: second relay will be switched ON, first relay will be switched OFF

• 4th press: both relays will be switched OFF

The above-mentioned two relays are defined according to parameters 101 & 102 (e.g. if “54” is set as the

parameter value, it means the fifth relay and fourth relay will be operated in inverse mode).

Note: This can be used to control motor directions with one button only.

Switches connected to external inputs (terminals S1-S5) can also be used to run scenarios or change modes in the

connected gateway or associated devices.

If the HE-RS01 is associated with a Z-Wave gateway, the scene controller and five binary switches will appear. The

scene controller indicates which external input was pressed, held, or released and allows the running of scenes on the

Z-Wave gateway. The five binary switches allow the relay outputs to be managed.

Scenarios

Scenarios can be created that allow connected devices to be triggered by the HE-RS01 onboard Real Time Clock

(RTC). The user should configure the output number, state, time, state change condition, in the Parameters (from 111

- 120) which will trigger the scenes.

Power and Energy Consumption

The HE-RS01 monitors all connected loads active (i.e. ‘real time’) power, and total energy consumption, through

software energy consumption logic. This data is periodically reported to the main Z-Wave controller according to

Parameter 04.

Total Energy Consumption is the electrical power being used by connected device in real time during use. Power

usage is calculated by the software using the values that were manually set when configuring Parameters 12-16,

multiplied by the time tracked when the HE-RS01 corresponding output was in an ON state. Using your connected

device’s power consumption specification (see associated owner’s manual), set the load in Watts for: “OUT-1” in

Parameters 12, “OUT-2” in Parameter 13, “OUT-3” in Parameter 14, “OUT-4” in the Parameter 15, and “OUT-5” in

Parameter 16.

Resetting Cumulative Consumption Memory:

The HE-RS01 enables you to erase stored consumption data through the Z-Wave network as follows:

1. Make sure the HE-RS01 is powered.

2. If not already done so, include the device into Z-Wave Gateway network

3. Reset memory consumption data using the Reset Command in COMMAND_CLASS_METER (see the Gateway

owner’s manual).

Note: Power cycling the HE-RS01 (On>Off>On) will not erase the consumption data as it is stored in non-volatile

memory.

Settings (available through Z-Wave network)

All configuration parameters are accessed through Z-Wave COMMAND_CLASS_CONFIGURATION

Parameters List & Factory Defaults

Number

Size

Description

Default

Value

Available Values

1 byte

Frequency Region

Read

Only

0 … 9

1 byte

Inclusion / Exclusion Mode

Read

Only

0, 1

bytes

Hardware and Software Versions

Read

Only

XXYYZZ

bytes

Energy Consumption, kW

Read

Only

Total consumption

5-6

Reserved by the manufacturer

1 byte

Relay 1 output NO or NC mode

0, 1

1 byte

Relay 2 output NO or NC mode

0, 1

1 byte

Relay 3 output NO or NC mode

0, 1

1 byte

Relay 4 output NO or NC mode

0, 1

1 byte

Relay 5 output NO or NC mode

0, 1

bytes

Power of the Relay 1 load in W

0…1100

bytes

Power of the Relay 2 load in W

0…1100

bytes

Power of the Relay 3 load in W

0…1100

bytes

Power of the Relay 4 load in W

0…1100

bytes

Power of the Relay 5 load in W

0…1100

17-18

Reserved by the manufacturer

1 byte

Time correction by controller

0, 1

Reserved by the manufacturer

1 byte

Week Day

1, 2, 3, 4, 5, 6, 7

1 byte

Time: Hour and Minutes

0 … 2359

Autres manuels pour QUINTO HE-RS01

Table des matières

Autres manuels Heltun Changer

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun HE-TPS02 Manuel utilisateur

Heltun

Heltun QUINTO HE-TPS05 Manuel utilisateur

Heltun

Heltun HE-TPS01 Manuel utilisateur

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun HE-HLS01 Manuel utilisateur

Heltun

Heltun QUINTO HE-RS01 Manuel utilisateur

Heltun

Heltun HE-TPS01 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur