Graco Pulse TLM Manuel utilisateur

3A5411J

Instructions

Pulse®TLM (Tank

Level Monitor)

Measures the distance between the device and the surface of the fluid beneath it to

determine the volume of fluid within a tank. Use with a Pulse operating system only.

Intended fluids: oil, waste oil, automatic transmission fluid (ATF), anti-freeze, windshield

washer solution, and waste water.

Not approved for use in European explosive atmosphere locations. For professional use

only.

Part No.: 25M449

Contains Model XBee S2C Radio, IC: 1846A-XBS2C.

The TLM contains FCC ID MCQ-XBS2C. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause

undesired operation.

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

NOTICE

•Do not over tighten TLM into tank

bung! Over tightening can cause perma-

nent damage and result in inaccurate

readings.

•Do not use thread sealant or adhesive!

Many of these products are chemically

incompatible with the ABS plastic. PTFE

tape is acceptable.

Contents

23A5411J

Contents

Warnings ........................................................................................3

Set Up ............................................................................................5

Configure the TLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TLM Registration Process .................................................6

TLM Display ...................................................................................6

Installation ......................................................................................7

Installation Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation .......................................................................................9

View Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Take Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Take Measurement - New Profile . . . . . . . . . . . . . . . . . . . . . 10

Refill the Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Daylight Savings Time (DST) Change . . . . . . . . . . . . . . . . . 10

Troubleshooting ...........................................................................11

Service .........................................................................................14

Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Parts .............................................................................................16

TLM Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Tank Specifications ......................................................................17

Vertical Tank: ..................................................................17

Horizontal Cylindrical Tank: .............................................17

Obround Tank: ................................................................18

Non-Standard Tanks: ......................................................18

Technical Specifications ...............................................................19

Graco Extended Tank Level Monitor Warranty ............................20

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Warnings

3A5411J 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this

equipment. The exclamation point symbol alerts you to a general warning and the hazard

symbols refer to procedure-specific risks. When these symbols appear in the body of this

manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols

and warnings not covered in this section may appear throughout the body of this manual where

applicable.

WARNING

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and wind-

shield wiper fluid, be aware that flammable fumes can ignite or explode. To help

prevent fire and explosion:

•Use equipment only in well-ventilated area.

•Eliminate all ignition sources, such as cigarettes and portable electric lamps.

•Ground all equipment in the work area.

•Keep work area free of debris, including rags and spilled or open containers of

solvent and gasoline.

•Do not plug or unplug power cords or turn lights on or off when flammable fumes

are present.

•Use only grounded hoses.

•Stop operation immediately if static sparking occurs or you feel a shock.Do

not use equipment until you identify and correct the problem.

•Keep a working fire extinguisher in the work area.

Warnings

43A5411J

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the low-

est rated system component. See Technical Specifications in all equipment

manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See

Technical Specifications in all equipment manuals. Read fluid and solvent

manufacturer’s warnings. For complete information about your material, request

Safety Data Sheets (SDSs) from distributor or retailer.

•Turn off all equipment and follow the Pressure Relief Procedure when equip-

ment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately

with genuine manufacturer’s replacement parts only.

•Do not alter or modify equipment. Alterations or modifications may void agency

approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you

are using it.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and

hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent seri-

ous injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.

Protective equipment includes but is not limited to:

•Protective eye wear, and hearing protection.

•Respirators, protective clothing, and gloves as recommended by the fluid and

solvent manufacturer.

WARNING

Set Up

3A5411J 5

Set Up

1. Install four, AA alkaline batteries (9) in

the battery holder (8). See Replacing

Batteries, page 14, Steps 1 - 6.

It is recommended that the TLM be

registered prior to installation.

The TLM operating parameters are

controlled by the Pulse software and set up by

the System Administrator.

NOTE: Manual TLM readings taken prior to

TLM configuration will be incorrect.

To register the TLM:

1. On the Pulse web portal, set the Hub, or

the remote extender that the TLM

communicates with, to DISCOVERY

mode.

2. Press and hold the Display button (A)

until the display (B) reads REGISTER,

then release (FIG. 2). This may take up to

20 seconds.

NOTE: A TLM will only display REGISTER if

a Hub, or remote extender, is within range

and in DISCOVERY mode.

3. The display reads REGISTER OK (FIG.

3, page 6) when the TLM is registered

with the Pulse software. This may take

up to 20 seconds.

If the TLM did not register with the Pulse

software, the error message REGISTER

E7 displays (see Step 1, FIG. 3).

Do not install or service this equipment

unless you are trained and qualified.

Installing and servicing this equipment

requires access to parts which may cause

fire, explosion, and serious injury if work is

not performed properly. Read Warnings,

page 3.

NOTICE

Do not over tighten TLM into tank bung!

Over tightening can cause permanent

damage and result in inaccurate readings.

Do not use the TLM with pressurized

tanks. Using the TLM in a pressurized tank

will damage the TLM.

Do not use thread sealant or adhesive.

Many of these products are chemically

incompatible with the Pulse/ABS plastic.

PTFE tape is acceptable.

FIG. 1

FIG. 2

TLM Display

63A5411J

Configure the TLM

1. Press the Display button (A) again to

configure the TLM with a new profile.

2. The display reads CONFIG OK, as

shown in FIG. 4, page 6, after the TLM is

configured with the new profile.

If the TLM was not configured with a new

profile by the Pulse software, the error

message CONFIG E8 displays (Step 2,

FIG. 4).

TLM Registration Process

Step 1: Connect Device

Step 2: Load Initial Profile

TLM Display

Registration

Displays REGISTER. Successful registration

adds a second line: OK. Registration failure

adds a second line: ERROR.

Profile

Displays CONFIG. Successful TLM

configuration adds a second line OK.

Unsuccessful TLM configuration adds a

second line ERROR.

Measurement Reporting

Displays REPORT. If data is successfully

transmitted, adds a second line OK. If data is

not successfully transmitted, adds a second

line ERROR.

Sensor Communication Error

If the sensor does not respond to commands

before timeout, a communication error is

flagged. Displays COMM ERR.

Bad Measurement

If there is a communication error during a

read measurement (i.e., timeout), or the

status from the read measurement command

indicates there is an issue, SENSOR ERR #

is displayed. The # corresponds to the

following Sensor Error Table.

SENSOR ERROR TABLE

FIG. 3

FIG. 4

Error Description

Sensor E0 Invalid reading or sensor

communication error

Sensor E1 No sensor PCBA detected

(damaged circuit board)

Sensor E4 Invalid profile parameter

Sensor E5 Measurement exceeds maximum

length

Sensor E7 Registration error

Sensor E8 Profile error

Sensor E9 RF communication error (no

acknowledge or no signal)

Installation

3A5411J 7

Installation

1. Remove the bung fitting and screw in the

TLM hand-tight.

•Do not use a wrench to tighten as

this may damage the TLM.

•Do not use thread lock adhesive as

this may damage the TLM.

2. Mount the TLM as close as possible to

the center of the tank.

3. Do not mount any fittings or T connects

between TLM and the tank.

NOTICE

Do not over tighten TLM into tank bung!

Over tightening can cause permanent

damage and result in inaccurate readings.

Do not use thread sealant or adhesive!

Many of these products are chemically

incompatible with the ABS plastic. PTFE

tape is acceptable.

Do not locate TLM next to the tank wall.

The wall can interfere with the sensor’s 30

degree cone angle.

Do not install the TLM in the tank’s fill

port. Repeated removal of the TLM will

damage the unit and void the warranty.

NOTICE

The TLM will not operate correctly if tilted

more than 2° from the surface of the tank

liquid.

The TLM will not operate correctly if the

TLM is mounted less than 5 in. (127 mm)

from the maximum possible fill height of the

fluid being measured.

The TLM will not read properly if:

•Fluid in the tank is agitated (e.g. filling

a tank with oil or anti-freeze). Be sure

to take all TLM readings when the fluid

in the tank is calm.

•The TLM is mounted next to the tank

wall or in a corner.

•If there is any structural bracing or

obstruction between the TLM and the

surface of fluid in tank.

FIG. 5

TLM must be mounted within 2° from per-

pendicular to the surface of the fluid.

Installation

83A5411J

FIG. 6

Installation Examples

Correct

Placement

Incorrect

Placement

Correct

Placement

Incorrect

Placement

Correct

Placement

Incorrect

Placement

Correct

Placement

Incorrect

Placement

Operation

3A5411J 9

Operation

View Data

The TLM can be configured with the Pulse

software to take a reading at predefined

times.

Press and release the display button (A).

Data appears on the display (B) (FIG. 7); each

screen lasting a few seconds before going on

to the next.

FIG. 8 shows the order that the screens

display when taking a measurement.

FIG. 9, page 10 shows the order that the

screens display when taking a measurement

after a new profile is entered using the Pulse

software.

NOTE: The tank level data can also be

viewed remotely using the Pulse software.

Take Measurement

FIG. 7

FIG. 8

Operation

10 3A5411J

Take Measurement - New

Profile

Refill the Tank

After a tank is refilled from an oil distributor or

a waste oil tank is emptied by a waste oil

service provider, press the display button (A)

(FIG. 7) on the TLM to ensure that the TLM will

maintain the most current tank volume status.

If the display button is not pushed, the TLM

will automatically read correctly at the next

scheduled tank reading.

Daylight Savings Time

(DST) Change

The Pulse software automatically adjusts the

time when daylight savings time changes

occur (Spring and Fall).

NOTE: The first TLM reading will be one hour

earlier or later (depending on the season,

Spring or Fall time change). All subsequent

TLM readings will be accurate.

FIG. 9: *NOTE: TLM will take a measurement

after a new profile has been loaded

Autres manuels pour Pulse TLM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Instrument de mesure

Graco

Graco Pulse TLM Manuel d'utilisation

Graco

Graco FX250 Manuel d'utilisation

Graco

Graco XDI12 Manuel utilisateur

Graco

Graco EFC C Series Manuel d'utilisation

Graco

Graco Magnum Project Painter 5 Manuel utilisateur

Graco

Graco 121325 Manuel d'utilisation

Graco

Graco IM20P Fiche technique

Graco

Graco Series D Manuel utilisateur

Graco

Graco 256282 Manuel utilisateur

Graco

Graco G3000 Manuel d'utilisation

Graco

Graco PM8 Guide de configuration

Graco

Graco EM5 Series Manuel utilisateur

Graco

Graco HG6000 Manuel de référence technique

Graco

Graco PPM 3050H Manuel d'utilisation

Graco

Graco Accu-Shot 233807 Manuel utilisateur

Graco

Graco Accu-Shot 233807 Manuel de la liste des pièces

Graco

Graco PE14 Manuel utilisateur

Graco

Graco FLOW METERS S3000 Manuel utilisateur

Graco

Graco ProControl 1KE Manuel de la liste des pièces

Graco

Graco G3000 Manuel d'utilisation

Graco

Graco G250 Manuel de la liste des pièces

Graco

Graco 244075 Manuel d'utilisation

Graco

Graco PSM Manuel utilisateur

Graco

Graco IniFlex Manuel d'utilisation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur