Futech 150.40.M Manuel utilisateur

MANUAL 150.40.M – QUATTRO MM [EN] V1.0 – 05.2022 |1

INSTRUCTION MANUAL [EN]

150.40.M – QUATTRO MM

OVERVIEW

1. Magnet

2. LED indicator(orange)

3. LED indicator(green)

4. LED indicator(red)

5. Laser sensitive area

6. Marking notch

7. Clamp

8. Keypad

9. Bubble vial

10. LCD display

11. Beeper

12. Battery cover

13. Type plate with serial number

14. Fixing thread of the clamp

Keypad

15. Power button On/Off

16. Beeper /Enter

17. Accuracy/ Arrow down

18. Grade LEDs /Arrow up

LCD Display

19. Numeric digits/text display

20. Grade indication arrow

21. On-grade indicator

22. Beeper indicator

23. Accuracy indicator

24. Battery indicator

2223

3 4 5 6 7

MANUAL 150.40.M – QUATTRO MM [EN] V1.0 – 05.2022 |2

Numeric digits/text display

[

]

• Three Digits display either the numeric evaluation (mm, cm, inch, or fractional inch) or simple text

messages.

• Resolution and decimal point is determined by the units of measure and the accuracy selected.

Grade indication arrow

[

]

• Horizontal bar indicates on-grade

• Four individual levels of grade information for above and below grade. The arrow size increase if the

distance from on-grade increases. The increment of arrow bars corresponds to the selected display

accuracy.

• Out of beam display: A sequent of arrows indicates if the receiver has moved beyond the vertical

reception range and will indicate in which direction to move to get back to laser beam. This function is

only available in rotating laser mode.

Operations

Prior to initiate the self-test, check whether the batteries have been installed correctly inside the device.

Insert batteries

A. Open the Battery cover [12]by hand.

B. Insert the battery making sure that the pole of the battery is in the right position.

C. Close the Battery cover [12].

Note:

• Only use AA battery.

• Close the Battery cover[12]firmly to maintain IP67 water and dust protection.

• Remove the battery if the device is not used for a longer period.

• When low battery [24]is indicated, do not operate the device, and replace the battery immediately.

Switch ON/OFF

§ Press the power button ON/OFF [15]to switch on the device. You hear one beep sound, and ‘Lin’

/’rot’ displayed on Numeric digits/text display[19]. This means the device is switched on.

§ Press again the power button ON/OFF[15]. The device beeps and ‘OFF’ displayed for one second on

Numeric digits/text display[19]This means the device is switched off.

§ In order to save the power, please switch off the device when the device is not in use.

Selecting rotary or line laser mode

If the device is not in the laser beam, it shows its detection mode:

‘Lin’ for line laser mode, and ‘rot’ rotating laser mode

• Hold the Power button ON/OFF [15]and Beeper /Enter button [16]simultaneously for about 3

seconds till a beep sounds.

• Text ‘Lin’ or ‘rot’ displayed on Numeric digits/text display[19]:

o ‘Lin’ indicates the Quattro MM will detect line laser.

o ‘rot’ indicates the Quattro MM will detect rotary laser.

Note:

• When the device is switched on, it starts in the operating mode used before it was switched off

last time.

• if in line laser mode, the device detects only the line laser color which is first detected after

switching on the device

MANUAL 150.40.M – QUATTRO MM [EN] V1.0 – 05.2022 |3

Adjusting the volume

Press the Beeper/Enter button [16]cycles

• High: Beeper indicator[22]is displayed,’ Hi’ shows for one second on Numeric digits/text

display[19].

• Low: Beeper indicator[22]is displayed, ’LOW’ shows for one second on Numeric digits/text

display[19].

• Off: no Beeper indicator[22]is displayed, ’OFF’ shows one second on Numeric digits/text

display[19].

Work with the laser receiver

• Switch on your construction laser. In case of line laser, activate the receiver mode on the laser.

• Switch on the device Quattro MM and select the correct laser type (rotary or liner laser) on your

Quattro MM

• Move the device up and down/left and right through the laser beam until the LED indicator (green) [3]

lights.

• The LED indicator (orange ) [2]and the LED indicator (red) [4]show in which direction you should

move the Quattro MM to find on-grade level.

• Mark the measured height at the Marking notch[6]

Note:

When you started using your Quattro MM with red laser level, you need to switch off and then switch

on our Quattro MM to start working with a green laser level. Also, for switching from green to red, you

need to power off/on the Quattro MM.

Adjusting the accuracy

§ Press Accuracy/Arrow down button [17]once. The Numeric digits/text display[19]shows

current accuracy setting on the LCD display [10].

§ Press again, while the accuracy is displayed (within one second), to change the current

selection. Subsequent presses will cycle through five accuracy options-Ultra

fine/Fine/Medium/ Coarse/ Ultra coarse.

inch

Fract.In

Display

Ultra fine

0,5

0,05

0,02

Flashing

Fine

1,0

0,1

0,05

1/8

Non-flash

Medium

2,0

0,2

0,1

1/4

Non-flash

Coarse

5,0

0,5

0,2

1/2

Non-flash

Ultra coarse

10,0

1,0

0,5

Flashing

Activate/deactivate LEDs

• Press Grade LEDs /Arrow up button [18].

• ‘ON’ appears on Numeric digits/text display[19]and three LED Indicators ([2], [3], [4]) flash for 3

seconds, The LEDs are activated, and the move direction is shown by the LEDs in addition to the display.

• Press Grade LEDs /Arrow up button [18]again to switch off the LED indications.

User defined on-grade level

An arbitrary level within-10 and +10 mm around the Marking notch [6]can be used as on-grade level.

§ Hold the Accuracy/Arrow down button [17]for two seconds while the device is in laser beam.

§ The device beeps one time, and an asymmetric symbol arrow[20]&[21]appears on LCD display[10].

This means the user defined on-grade level succeeds.

§ When the laser beam is outside of allowed area (10 and +10 mm), you hear one beep sound and text

‘E30’ appears on Numeric digits/text display[19]. This means user defined on-grade level fails.

§ Reset user defined on-grade level to default

MANUAL 150.40.M – QUATTRO MM [EN] V1.0 – 05.2022 |4

o While the device is out of laser beam, hold the Accuracy/Arrow down button [17]for two

seconds, the on-grade level is reset to default.

o If the device is switched off, the on-grade level is automatically reset to default.

o If you want to save the user defined on-grade level permanently, you can choose this option

in the menu (see Menu Entries-OFS)

Use the menu

You can use the menu functions to edit settings. For most applications, the factory defaults are the best choice.

We recommend changing settings only in special applications.

• Hold the Beeper /Enter button [16]for more than two seconds until the device beeping once and text

‘SEn’ displayed on Numeric digits/text display[19], enter the menu functions.

• Browse menu items by pressing the Accuracy/Arrow down button [17]or Grade LEDs /Arrow up

button [18].

• Select menu items by pressing the Beeper /Enter button [16]

• When the menu item is selected, you may browse item values by pressing the Accuracy/Arrow down

button [17]or Grade LEDs /Arrow up button [18].

• Select item value by pressing the Beeper /Enter button [16]

• Press he Power button ON/OFF [15], exit the menu functions.

Menu Entries

‘Sen’ - Sensitivity: Hi(gh)/Low Default: High. Set it to Low if you have problems with disturbing sources like

fluorescent or strobe lights.

• ‘AvG ‘- Averaging: Hi(gh) / Low Default: Low. Set it to High if you need to have more stable

readings under difficult atmospheric conditions.

• ‘Unt ‘- Unit: mm / cm / in(ch) / f(ract). in(ch)

Default: mm. Choose desired numeric elevation display unit.

• o.o.b - Out of beam display: On/OFF Default: OFF. Switch Out-of-beam display on and off. For a

description see chapter LCD Display.

• ‘OFS’-User-defined on-grade level: tmP(temporary) / PEr(manent)

Default: temporary. To deactivate the function, choose OFF. To save the user-defined on-grade level

permanently, choose ‘Per’.

• InF - Device InformationFind Information about Firmware Version (Fw), Device Code (dc) and Serial

Number (Sn) here.

Note:

All menu settings will be retained when the device is turned off

Autres manuels Futech Instrument de mesure

Futech

Futech DECACROSS Manuel utilisateur

Futech

Futech WS6300 Manuel utilisateur

Futech

Futech PARA DS Manuel utilisateur

Futech

Futech DISTY 40R Manuel utilisateur

Futech

Futech PROCROSS 8.0 DS Manuel utilisateur

Futech

Futech DISTY 120RC Manuel utilisateur

Futech

Futech DISTY60 Manuel utilisateur

Futech

Futech MULTICROSS 4D ELECTRONIC Manuel utilisateur

Futech

Futech Drill Pointer 2 Manuel utilisateur

Futech

Futech WS4300 Manuel utilisateur

Futech

Futech AMPCLAMP 1000 Manuel utilisateur

Futech

Futech 031.03 Manuel utilisateur

Futech

Futech RED RUNNER Manuel utilisateur

Futech

Futech MEGACROSS Manuel utilisateur

Futech

Futech QUATTRO Manuel utilisateur

Futech

Futech DISTY40 Manuel utilisateur

Futech

Futech GYRO RED Manuel utilisateur

Futech

Futech HYDRO Manuel utilisateur

Futech

Futech Quatro Manuel utilisateur

Futech

Futech DISTY 40R Manuel utilisateur

Futech

Futech MULTICROSS 3 Super Vision Manuel utilisateur

Futech

Futech PLUTO 1.2 Manuel utilisateur

Futech

Futech DISTY 120RC Manuel utilisateur

Futech

Futech PROCROSS 8.0 DS Guide d'installation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur