Futech DM3540 Manuel utilisateur

USER

MANUAL

DM3540 DISTANCE METER - 40M

DM3560 DISTANCE METER - 60M

EN ENGLISH

Manual in your

language?

Check the back cover

OVERVIEW

G H I J

MIN

MAX

m88888

88888

KEYPAD

01 Function button

02 Add/subtract button / Unit button

03 Measure / Power ON button

04 Clear / Power OFF button

05 Reference button

06 Battery cover

SCREEN

A Laser ON/OFF

B Reference point at front of device

C Reference point at back of device

D Function indicator

E MAX indicator (continuous measurement)

F MIN indicator (continuous measurement)

G Volume indicator

H Battery indicator

I Emission signal strength

J Signal strength indicator

K Third display line

L Second display line

M First display line

N Main display line

SAFETY

Please read the safety instructions is provided in the separate

booklet provided with the device before using.

The improper use of this product may result in dangerous inju-

ries of laser radiation, electric shock and personal injuries.

Do not try to change the performance of the laser device in any

way, as it may result in danger caused by laser exposure. The

laser can only be opened for use.

LASER RADIATION - Class 2 laser product.

Do not stare into beam.

Please store device in a safe location to prevent the use by

unauthorized personnel.

BATTERY

The device can be powered using the two AAA 1,5V alkaline

batteries that are included.

INSTALLING THE BATTERY

·Open the battery cover [06].

·Insert two alkaline AAA batteries of 1,5 Volt (ensure to align

the correct polarity).

·Close the battery cover [06].

NOTE

When the battery level is low, the battery indicator [H] ashes

5 times. Replace the batteries as described above.

FIRST TIME USAGE

Remove all protection foils.

USE

·Turn on the device: press the Measure/Power ON button [03].

The laser will be activated and the device is ready to use.

·Turn off the device: hold the Clear/Power OFF button [04].

NOTE

The device will automatically shut down when no operations

are preformed within 45 seconds.

SELECT REFERENCE POINT

The standard reference point is set at the back of the device [C],

thus including it’s length in the measurement.You can change

the reference point by pressing the reference button [05].

·Press the reference button [05] once to change the reference

point to the front of the device [B]. The device length is now

excluded from your measurements.

·Press the reference button [05] again to change the reference

point back to the back of the device [C].

You can check your reference point using the indicators [B] and

[C]

ON ON

CHANGE UNITS

This device can show the measured distances in different units.

The available units are meten (m), inch (in), feet (ft), inch + feet

(in+ft).

·Change the distance units by holding the Add/subtract button

/ Unit button [02] until your desired unit is selected.

SINGLE MEASUREMENT

·Once the device is on, press the measure button [03] once to

take a single measurement.

The result will be shown on the main display line [N]. The laser

will turn off after the measurement. Press the measure button

[03] again to turn the laser back on and make the device ready

for a new measurement.

Taking subsequent measurements will always push the previous

measurement up one display line. Main display line [N]  rst

display line [M] second display line [L] third display line

[K]. A maximum of the last four measurements will be displayed.

CONTINUOUS MEASUREMENT (MIN/MAX)

With continuous measurement, measurements are taken con-

tinuously from activation of the function until the function is de-

activated. This allows you to know the minimum and maximum

distance measured during these measurements. For example, to

know the exact distance to the furthest corner point.

·Once the device is on, activate continuous measurement by

holding the Measure button [3] until the fucntion starts.

A repeating beep will be heard. With each beep, a new

measurement is taken.The last measured result, which update

continuously, is shown in the Main display line [N]. The mini-

mum distance measured during this session is shown in the First

display line [M], the maximum distance measured in the Second

display line [L].

·Stop the continuous measurement by pressing the measure

button [3].

The last measured result is shown in the Main display line [N].

The minimum distance measured during this session is shown

in the First display line [M], the maximum distance measured in

the Second display line [L].

ADD/SUBTRACT

This function allows you to add or subtract two single measure-

ment

·Take a rst measurement by pressing the measure button [03].

·Press the Add/Subtract [02] button 1x to add the next meas-

urement, 2x to subtract the next measurement.

The measured value moves to the second display line [L].A “+”

or “−” is shown in front of the rst display line [N]. The device is

ready to make the second measurement.

·Make a second measurement by pressing the measure button

[03].

The result of the second measurement will be visible in the rst

display line [N]. The result (the addition or subtraction of the two

measurements) can be read in the main display line [M].

·Add or subtract (depends on which you’ve choose for the rst

calculation) an additional measurement can be done by press

the measure button [03] to activate the laser again, and press

it a second time to make the measurement.

The result of the rst calculation moves to the second display

line [L], the result of the second measurement is shown on the

rst display line [M]. The new result of the calculation will be

visible on the main display line [N].

NOTE

To change from “+” to “−” (or vica versa) for making the sec-

ond measurement can be done by pressing the add/subtract

button [02]. The result of the rst calculation moves to the

second display line [L], the symbol in front of the rst display

line [M] changes from “+” to “−” (or vica versa). This action

also activates the laser and makes the device ready to measure

the additional distance. You can make the new measurement

by pressing the measure button [03].

You can repeat this steps just as much as needed.

AREA MEASUREMENT

This device allows you to calculate the area of a

(rectangular) area.

·Press the function button [01] once.

The function indicator [D] will show you the area measurement

symbol. The ashing line in this function indicator [D] shows

which lenght you have to measure.

·Measure the rst side of the rectangle, indicated by the func-

tion indicator [D], by pressing the measure button [03].

The length of the rst measured side is shown on the third

display line [K].

·Measure the second side of the rectangle, indicated by the

function indicator [D], by pressing the measure button [03].

The length of the second measured side is shown on the second

display line [L]. The result of the calculation, the area, can be

read in the main display line [N].

NOTE

Keep the device as levelled as possible for the most accurate

measurements.

VOLUME MEASUREMENT

This device allows you to calculate the volume.

·Press the function button [01] twice.

The function indicator [D] will show you the volume measure-

ment symbol. The ashing line in this function indicator [D]

shows which length you have to measure.

·Measure the rst side, indicated by the function indicator [D],

by pressing the measure button [03].

The length of the rst measured side is shown on the third

display line [K].

·Measure the second side, indicated by the function indicator

[D], by pressing the measure button [03].

The length of the second measured side appears on the second

display line [L].

·Measure the third side (height), indicated by the function

indicator [D], by pressing the measure button [03].

The length of the third measured side (height) is shown on the

rst display line [L]. The result of the calculation, the volume, can

be read in the main display line [N].

INDIRECT MEASUREMENT (PYTHAGORAS)

Indirect measurement mode allows you to calculate the distance

between two measured points as long as the second

measurement is made using a proper 90° angle (shortest

distance).

·Press the function button [01] three times

The function indicator [D] will show you the indirect measure-

ment symbol. The ashing line in this function indicator [D]

shows which length you have to measure.

·Measure the rst side, indicated by the function indicator (this

is also the longest side of the sides to measure) by pressing

the measure button [03].

The length of the rst measured side is shown on the third

display line [K].

·Measure the second side indicated by the function indicator

[D], by pressing the measure button [03]. Keep in mind that

this side needs to be the shotest side of the sides to measure

AND this second measurement should be made at a 90° angle

to the point to be measured.

The length of the second measured side is shown on the second

display line [K]. The result of the calculation, the distance

between the rst and the second measured point, can be read in

the main display line [N].

ADDITIVE PYTHAGOREAN MEASUREMENT

Additive pythagorean measurement, or Double pythagorean

measurement mode, allows you to calculate the height by

adding the calculated sides of the two measured triangles.

·Press the function button [01] four times

The function indicator [D] will show you the additive pythago-

rean measurement symbol. The ashing line in this function

indicator [D] shows which length you have to measure.

·Measure the rst side, indicated by the function indicator by

pressing the measure button [03].

The length of the rst measured side is shown on the third

display line [K].

·Measure the second side indicated by the function indicator

[D], by pressing the measure button [03]. Keep in mind that

this side needs to be the shotest side of the sides to measure

AND it should be made at a 90° angle to the point to be

measured. This second points needs to be between the rst

and third measured point.

The length of the second measured side is shown on the second

display line [K].

·Measure the third side indicated by the function indicator [D],

by pressing the measure button [03].

The length of the third measured side is shown on the rst dis-

play line [M]. The result of the calculation, the distance between

the rst and the third measured point, can be read in the main

display line [N].

SUBTRACTIVE PYTHAGOREAN MEASUREMENT

Substractive pythagorean measurement,or reverse double

pythagorean measurement mode allows you to calculate the

distance between two measured points by subtracting the

calculated sides of the two measured triangles.

·Press the function button [01] ve times

The function indicator [D] will show you the substractive pythag-

orean measurement symbol. The ashing line in this function

indicator [D] shows which length you have to measure.

·Measure the rst side, indicated by the function indicator by

pressing the measure button [03] (the longest hypotenuse).

The length of the rst measured side is shown on the third

display line [K].

·Measure the second side indicated by the function indicator

[D], by pressing the measure button [03] (the shortest hypot-

enuse). This second points needs to be between the rst and

third measured point.

The length of the second measured side is shown on the second

display line [K].

·Measure the third side indicated by the function indicator [D],

by pressing the measure button [03]. Keep in mind that this

side needs to be the shotest side of the sides to measure AND

this second measurement should be made at a 90° angle to

the point to be measured.

The length of the third measured side is shown on the rst dis-

play line [M]. The result of the calculation, the distance between

the rst and the second measured point, can be read in the main

display line [N].

CLEAR DATA

Use the Clear button [04] to clear or delete previously saved data

and measurements.

TECHNICAL SPECIFICATIONS

MODEL DM3540 DM3560

Accuracy +/- 3mm

Range 40m 60m

Measurement units m / in / ft / in + ft

Continuous measurement Yes

Min/Max Yes

Surface Yes

Volume Yes

Pythagoras Yes (x3)

Add Yes

Subtract Yes

Automatic shutdown Yes

Battery 2x 1.5V AAA

Operation temperature 0°C ~ +40°C

Laser Class 2, 630-640 nm, Red

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Futech Instrument de mesure

Futech

Futech MULTICROSS 5 SUPER Vision Manuel utilisateur

Futech

Futech GYRO RED Manuel utilisateur

Futech

Futech PROCROSS 8.0 DS Guide d'installation

Futech

Futech MULTICROSS 3D COMPACT 030.03D Manuel utilisateur

Futech

Futech TERACROSS Manuel utilisateur

Futech

Futech DISTY 120RC Manuel utilisateur

Futech

Futech HYDRO Manuel utilisateur

Futech

Futech DECACROSS Manuel utilisateur

Futech

Futech 150.40.M Manuel utilisateur

Futech

Futech WS6300 Manuel utilisateur

Futech

Futech MULTIPOWER 4.6 Manuel utilisateur

Futech

Futech MULTICROSS 8 HIGH PRECISION SUPER BRIGHT... Manuel utilisateur

Futech

Futech MULTIPOWER 4.6 Manuel utilisateur

Futech

Futech PROCROSS 8.0 DS Manuel utilisateur

Futech

Futech MEGACROSS Manuel utilisateur

Futech

Futech WS4300 Manuel utilisateur

Futech

Futech MULTISCAN 196.20 Manuel utilisateur

Futech

Futech MULTICROSS 3D Manuel utilisateur

Futech

Futech PLUTO 1.2 Manuel utilisateur

Futech

Futech MULTICROSS 3 Manuel utilisateur

Futech

Futech T-BEVEL-30 Manuel utilisateur

Futech

Futech DISTY40 Manuel utilisateur

Futech

Futech DISTY60 Manuel utilisateur

Futech

Futech DISTY 40R Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur