FujiFilm Frontier-S DX100 Manuel utilisateur
DX100 Field Maintenance Guide
is guide has been created to help you maintain your DX100 printer’s peak performance and
quality. It is important to utilize these maintenance procedure based on your environmental
usage of the printer. e frequency of some of these maintenance items may need to be
performed more oen based on these conditions.
1
DX100 Field Maintenance Guide
Glossary of Tasks
•Dusting off the paper roll
oWhen a new roll of paper is opened. It is important to utilize a lint free cloth to wipe the
edges of the paper off prior to inserting the paper spindle flanges.
Doing so will help to minimize the amount of paper dust being ingested into
vital printer sections.
•Emptying waste paper box
oIt is important to empty the waste paper box when the paper is changed. If the paper
slugs build up in the box they can be ingested by the printer and cause damage to the
cutter, fans, and also cause paper jams.
•Clean the outside of the printer
oEvery start of the day the printer’s exterior should be wiped down with a damp cloth.
Being certain the area where the prints exit the printer kept clean of debris.
•Clean the roll unit
oDaily, it is important to clean the roll unit. Utilizing a lint free cloth. First, by wiping out
the roll units. Then lift the rear plate and wipe out from behind this plate to remove any
dust or lint. Next, lift the front plate to clean behind this unit. It is also important to wipe
across the felt pads to help lift some of the paper dust that may have accumulated in
these pads
It is important not to vacuum this section. The suction from the vacuum can
dislodge the small white rollers
•Cleaning ink/paper dust from upper platen
oDaily, the upper platen should be checked for excessive ink and paper dust. To clean this
section it is recommended to use a bemcot moistened with water and lightly dab the
absorbent material where the paper dust has accumulated. Next, uses a new bemcot
moistened with water and wipe the plastic sections of the upper platen.
By keeping this section clean of debris and ink build up will prevent ink from
being transferred to the prints.
2
•Clean ink from upper paper guide rollers
oDaily inspection: If the upper platen is not properly maintained, ink may be transferred
to the rollers of the paper guides. Utilize a bemcot moistened with water to clean these
rollers.
It is extremely important not to push down on these rollers, pushing too hard
can dislodge them from the guides.
•Vacuum Anti-condensing fans
oBi-Weekly: These fans should be inspected weekly for any dust or debris build up
vacuuming them bi-weekly to keep the dust and debris from collecting in and around
these fans
•Vacuum air filters
oMonthly vacuum the air filter for the power supply and cooling fans. Keeping these
filters clear of dust and debris will improve the efficiency of keeping the vital boards
cool and operating.
•Cleaning the feed rollers (roll unit)
oMonthly, at the end of a work day, it is recommended that the rubber feed rollers be
cleaned with a damp bemcot. By doing this at the end of the day will allow the rollers to
dry properly.
•Clean the feed rollers (rear cover)
oMonthly, at the end of a work day, it is recommended that the rubber feed rollers be
cleaned with a damp bemcot. By doing this at the end of the day will allow the rollers to
dry properly.
Troubleshooting:
•Ink lines on prints
oWhen lines appear on the front and back of prints it is important to check and clean the
upper platen and upper paper guides
•White edge on prints
3
oWhen a small white edge appears on the prints, this may be a result of the paper
meandering while bee fed through the printer
Check that the paper is tight on the spindle by pressing the black and grey
flanges together so that they tight against the edges of paper
Check the paper guides in the roll unit to be sure the front and rear paper
guides are set and locked into position for the paper size loaded.
•W-1108: Paper Size Error
oIf you encounter with a W-1108 error this may be caused by the paper flange not being
tight against the edge of the paper. Remove the paper from the roll unit and press the
grey and black flanges tightly against the paper and reload the paper verify both the
front and rear paper guides are set correctly. If the error persists please contact the help
desk.
•W-1102: Paper Jam (Rear Cover/ Top Cover)
oW-1102 indicates that a paper jam has occurred. After removing the roll paper verify
both the front and rear paper guides are set to the correct paper width.
oInspect the roll unit for any debris such as paper slugs, torn pieces of paper, excessive
dirty rollers.
oInspect the inlet roller by following these steps
•E-2101: Tube Maintenance Error
oThe E-2101 message will be displayed when the ink tubes are close to being to their
service life. It is recommended to contact the help desk for further instruction. It is also
important to understand your printer’s warranty.
•E-9901: Fatal Error
oA fatal error occurs when there is a mechanical malfunction. It is important to contact
the help desk for further assistance on a potential remedy for the specific error code.
•Service call error 1102
oThis error will be associated with an E=9901 indicating the ink tubes will need to be
serviced, at this point the printer will need to be serviced. You must contact the help
desk for further instructions.
4
Dusting o the Paper Roll
Paper dust can accumulate on the ends of the roll paper during manufacturing. When the
paper is removed from the packaging. It is important to wipe o both ends of the roll prior
to placing it on the paper spindle.
1. With a lint free cloth set the paper on
end as shown and wipe around the top of
the roll to remove any dust.
2. Carefully turn the roll over and dust o
the other end.
Important: ese step should be followed
for every paper change.
5
Empty the Wastepaper Box
It is extremely important to empty the wastepaper box aer every roll of paper. By having the paper slugs
collect in the box can result in the slugs being introduced back into the printer causing mechanical failures
and paper jamming .
2. Re-install the wastepaper box
1. Remove the wastepaper box then discard
the paper slug in the trash.
6
Cleaning outside surfaces of the
DX100
To keep your printer looking its best. It recommended to clean the outside of the printer to control the
amount of dust and debris that can collect on its surface.
2. Wipe the rear and sides of the printer.
1. With a cloth moistened with water wipe
the front and sides of the printer. Be sure to
wipe slightly inside the print exit section.
7
Cleaning the Roll Unit
e roll unit is a vital part of the DX100’s paper transport section. It is important to maintain this sections
cleanliness by follow the steps below.
2. Release the blue lock lever to open the
roll unit.
1. Remove the wastepaper box
Important: Do not vacuum near the
white rollers of the roll unit doing so may
dislodge the small white rollers.
8
Cleaning the Roll Unit
3. Utilizing a list free cloth or a bemcot.
Gently wipe the inside of the roll unit to
remove any dirt or debris.
9
Cleaning the Roll Unit
5. Gently wipe this area in an up and down
manner to dust and clear the area of any
debris.
Note: Be careful not to dislodge any white
rollers
4. Li up the rear plate by placing your
nger in the teardrop hole and liing
upwards.
10
Autres manuels pour Frontier-S DX100
4
Table des matières
Autres manuels FujiFilm Imprimante
FujiFilm
FujiFilm ASK-300 Manuel utilisateur
FujiFilm
FujiFilm Apeos 7580 Manuel utilisateur
FujiFilm
FujiFilm Revoria Press EC1100 Manuel utilisateur
FujiFilm
FujiFilm Revoria Press SC180 Manuel utilisateur
FujiFilm
FujiFilm Apeos 7580 Manuel utilisateur
FujiFilm
FujiFilm Apeos 5330 Manuel utilisateur
FujiFilm
FujiFilm ApeosPort - VII C4421 Manuel utilisateur
FujiFilm
FujiFilm Frontier LP7500 Comment utiliser
FujiFilm
FujiFilm FM-DP L Manuel utilisateur
FujiFilm
FujiFilm Apeos C7070 Manuel utilisateur
FujiFilm
FujiFilm Revoria Press E1136 Manuel utilisateur
FujiFilm
FujiFilm instax mini Link 2 Manuel utilisateur
FujiFilm
FujiFilm ApeosPro C810 Manuel utilisateur
FujiFilm
FujiFilm SP-3000 Manuel utilisateur
FujiFilm
FujiFilm instax SHARE SP-2 Manuel utilisateur
FujiFilm
FujiFilm DL410 Comment utiliser
FujiFilm
FujiFilm CR-IR 362 Manuel utilisateur
FujiFilm
FujiFilm Revoria Press EC1100 Manuel utilisateur
FujiFilm
FujiFilm MP-70 Manuel utilisateur
FujiFilm
FujiFilm Frontier-S DX100 Manuel utilisateur
