FujiFilm Frontier-S DX100 Manuel utilisateur
Revision 2.04 - V4.3 Driver- 11/23/16
Frontier-S DX100 printer with
DarkRoom Pro Software
Windows V4 Driver
Version 9.1.1978 Basic Driver
and
DarkRoom 9.20.2232 or higher for Advanced Driver integration
Installation Guide
Revision 2.04 - V4.3 Driver- 11/23/16 2
This page is
intentionally left
blan
k
Revision 2.04 - V4.3 Driver- 11/23/16 3
Table of Contents
Introduction 4
General System Information and Note on USB Port Installation 5
System Topology 6
Software, hardware and documents needed for this installation
Setting up the Frontier-S DX100 Printer 7
Installing the DarkRoom Pro software on the Client PC 8
Setting up the Frontier-S DX100 printer(s) on the DarkRoom PC 12
Setup and use of DarkRoom Pro 23
Appendix: Operation Notes; Color Management with Windows
Driver and DarkRoom 26
Revision 2.04 - V4.3 Driver- 11/23/16 4
Introduction
This guide will provide you with the necessary steps that need to be taken to install the Frontier-S
DX100 with DarkRoom Pro software using Version 9.1.1978 and Version 9.2 and higher.
Please Note: To take full advantage of the Fujifilm DX100 V 4 Driver with DarkRoom Pro
you must have DarkRoom Pro Version 9.2.2232 or higher. This will enable automatic set up of
the “Fujifilm DX100 EX” printer.
Set up in Versions 9.1.1978 or lower can be accomplished by use of the Windows Driver Printer
Set Up in DarkRoom Pro. In this basic option you will need to refer to your DX100 Operators
Manual for creation of custom page sizes.
To take full advantage of advanced integration of DX100 it is necessary to upgrade to the latest
version of DarkRoom Pro Version 9.2.2232 and higher uses direct drivers to communicate with
the DX100 printer. Benefits from this upgrade are advanced set up options in the driver as well
as automated page size selection and more efficient production.
Darkroom Pro software is to be installed on a client supplied PC (System PC) that meets the
following specifications:
Windows 7 Service Pack 1, 32 or 64 Bit
Windows 10 Pro 32 or 64 Bit
It is important that DarkRoom Pro software is installed on a computer that has the ability to
accommodate the workload of both software and the video graphics requirements of an imaging
workstation.
The DX100 Printer(s) connect directly to the DarkRoom Pro Workstation/PC via USB cable(s). A
total of up to *6 printers has been tested and is supported.
Revision 2.04 - V4.3 Driver- 11/23/16 5
General System Information
Note on Printer USB Port Installation: The Frontier-S DX100 printer connects to DarkRoom
Pro computer as USB connection one computer to multiple printers. Note location, port number
and printer number when installing. If a printer is disconnected or replaced connect only to the
port that the printer was originally installed on. When swapping or replacing a printer, refer to
the DX100_Printer_Driver_Operation_Guide_EN.pdf Fourth Edition and use of Frontier-S DX100
Maintenance Tool for correct registration of the printer.
See Topology Illustration on Page 7.
Minimum requirements for the DarkRoom PC computer (Client PC) are that it will need to support
the Operating System installed with RAM, (4Gb) Hard Drive Space (200 Gb). The system must
be capable of handling advanced image processing applications.
Operating Systems supported are Windows XP Pro with SP 3, OR Windows 7 Service Pack 1 ,
32/64 Bit, Windows 10 Pro 32/64 Bit.
Before you proceed with the installation it is important that you review and understand the
installation guide. Be familiar with the installation steps before beginning the installation.
Revision 2.04 - V4.3 Driver- 11/23/16 6
System Topology
The illustration below shows a Host PC which meets minimum configurations outlined in the
DX100 Installation Manual, Frontier-S Printer Driver Operation Guide EN.pdf Fourth
Edition. DarkRoom Pro is installed on the Client PC. The DX100 Printer is connected to the Host
PC via USB.
DX100 Connected via USB to the DarkRoom Pro Computer
Revision 2.04 - V4.3 Driver- 11/23/16 7
Software, hardware and documents needed for this installation:
Customer provided Computer which matches minimum specifications outlined in
General Information.
Fujifilm Frontier-S DX100 Printer(s)
DarkRoom Pro software and License/USB Dongle, supplied by FUJIFILM NAC
Marketing/Sales, or purchased directly from DarkRoom Software LLC
DarkRoom Pro Installation Guide and Quick Start Guide, supplied with the DarkRoom
software package
DX100 Windows Driver Software v 4 or higher, supplied with the Printer
Frontier-S Printer Driver Operation Guide EN.pdf Fourth Edition supplied with the
Printer
DarkRoom Pro installation Disk Version 9.10.1978, 9.2 or higher is preferred.
Setting up the DX100 Printer
Installation Preparation and unpacking the printer
Unpack and install the Frontier-S DX100 Printer as described in the Frontier-S DX100
Installation Manual supplied with the printer.
Printer Installation
Continue with the Printer installation of the Windows Driver following directions in
DX100_Printer_Driver_Operation_Guide_EN.pdf Fourth Edition - Pages 4 through 5.
Installation and Settings: Frontier-S DX100 Printer Driver Operation Guide EN.pdf
Fourth Edition pages 9 through 12
Review
Review and follow the instructions for the use of the Frontier-S DX100 Printer Driver
Operation Guide EN.pdf Fourth Edition Pages 12 through 50.
Revision 2.04 - V4.3 Driver- 11/23/16 8
Installing DarkRoom Pro software on the System PC
The Frontier-S DX100 S should be set up following instructions found in General Information and
Frontier-S Printer Driver Operation Guide EN.pdf Fourth Edition
To Install DarkRoom Pro on your host computer:
1. Insert the DarkRoom Pro installation disk into the DVD drive
2. If the Dvd does not automatically run
3. Click on Start > Run… > Browse..
4. Select SetupDRPRoxxxx.exe
5. Click OK to run the installer
6. Click OK
7. The Install Shield Wizard will start
Revision 2.04 - V4.3 Driver- 11/23/16
9
8. When the DarkRoom Professional installer starts, Click Next
9. Select the Radio button to “Accept the terms in the license agreement” and Click Next
Revision 2.04 - V4.3 Driver- 11/23/16
10
10. Click Next
11. Click Install
Autres manuels pour Frontier-S DX100
4
Table des matières
Autres manuels FujiFilm Imprimante
FujiFilm
FujiFilm 16558126 Manuel utilisateur
FujiFilm
FujiFilm DART 4300E Manuel utilisateur
FujiFilm
FujiFilm Apeos C8180 Manuel utilisateur
FujiFilm
FujiFilm Apeos 5330 Manuel utilisateur
FujiFilm
FujiFilm Frontier-S DX100 Manuel utilisateur
FujiFilm
FujiFilm Pivi MP-300 Manuel utilisateur
FujiFilm
FujiFilm DryPix 7000 Manuel utilisateur
FujiFilm
FujiFilm DL410 Comment utiliser
FujiFilm
FujiFilm Apeos 7580 Manuel utilisateur
FujiFilm
FujiFilm instax mini Link 2 Manuel utilisateur
FujiFilm
FujiFilm instax SHARE SP-2 Manuel utilisateur
FujiFilm
FujiFilm PICTROGRAPHY 4500N Manuel utilisateur
FujiFilm
FujiFilm instax mini Link Manuel utilisateur
FujiFilm
FujiFilm Apeos C7070 Manuel utilisateur
FujiFilm
FujiFilm Pictrography series Manuel utilisateur
FujiFilm
FujiFilm Revoria Press SC170 Manuel utilisateur
FujiFilm
FujiFilm FLA-8000 Manuel utilisateur
FujiFilm
FujiFilm Frontier-S DX100 Manuel utilisateur
FujiFilm
FujiFilm ASK-300 Manuel utilisateur
FujiFilm
FujiFilm ApeosPro C810 Manuel utilisateur
