Fluke ScopeMeter 225C Manuel utilisateur

Fluke 19xC-2x5C

ScopeMeter

Software version 8.00 onwards

Getting Started

Jun 2008, Rev. 1, 09/2009

All product names are trademarks of their respective companies.

Table of Contents

Title Page

Unpacking the Test Tool Kit ........................................................................................... ii

Introduction .................................................................................................................... 1

Contacting Fluke ............................................................................................................ 1

Safety Information: Read First........................................................................................ 1

Preparing for Use ........................................................................................................... 4

Powering/Resetting the Test Tool .................................................................................. 4

How to Navigate a Menu (example) ............................................................................... 4

Changing the Information Language .............................................................................. 5

Adjusting Contrast and Brightness ................................................................................. 5

Using the Scope ............................................................................................................. 5

Multimeter ...................................................................................................................... 7

Recorder Functions ........................................................................................................ 8

Fieldbus Measurements (Bushealth).............................................................................. 8

Replay ............................................................................................................................ 10

Zoom .............................................................................................................................. 10

Making Cursor Measurements ....................................................................................... 11

Triggering ....................................................................................................................... 11

Saving/Printing Screens and Setups .............................................................................. 13

User Options .................................................................................................................. 20

Fluke 19xC-2x5C

Getting Started

Unpacking the Test Tool Kit

The following items are included in your test tool kit:

1. ScopeMeter Test Tool

2. Battery Charger

3. 10:1 Voltage Probe Set (Red)

4. 10:1 Voltage Probe Set (Gray)

5. Test Lead Set (Red and Black)

6. Bus Health Test adapter (2x5C

only)

7. Safety Information + CD ROM

with complete Users Manual

8. Shipment box (basic version

only)

The -S versions also include:

9. Optically Isolated USB

Adapter/Cable

10. CD ROM with FlukeView®

Software

11. Hard Case

127

(2x)

Fluke 215C/225C

S-version

Figure 1. ScopeMeter Test Tool Kit

Getting Started

Introduction

This Getting Started Manual provides basic information

on Models 192C, 196C, 199C, 215C and 225C, software

versions V08.00 and newer. Refer to the Users Manual

on the accompanying CD-ROM for complete operating

instructions.

Contacting Fluke

To locate an authorized service center, visit us on the

World Wide Web at: www.fluke.com

or call Fluke using any of the phone numbers listed

below:

+1-888-993-5853 in the U.S.A and Canada

+31-40-2675200 in Europe

+1-425-446-5500 from other countries.

Safety Information: Read First

The Fluke Models 192C, 196C, 199C, 215C and 225C

ScopeMeter test tools (hereafter referred to as “test tool”)

comply with:

•ANSI/ISA S82.01-1994

•EN/IEC61010-1 : 2001

•CAN/CSA-C22.2 No.61010-1-04

•1000 V Measurement Category II, 600 V

Measurement Category III, Pollution Degree 2

•UL61010B-1

Use the test tool only as specified in the Users Manual.

Otherwise, the protection provided by the test tool might

be impaired.

A Warning identifies conditions and actions that pose

hazard(s) to the user. A Caution identifies conditions and

actions that may damage the test tool.

Fluke 19xC-2x5C

Getting Started

Warning

To avoid electrical shock or fire:

•Use only the Fluke power supply, Model

BC190 (Battery Charger / Power Adapter).

•Before use check that the selected/indicated

voltage range on the BC190 matches the local

line power voltage and frequency.

•For the BC190/808 universal Battery

Charger/Power Adapter use only line cords

that comply with the local safety regulations.

Note

To accommodate connection to various line

power sockets, the BC190/808 universal Battery

Charger / Power Adapter is equipped with a male

plug that must be connected to a line cord

appropriate for local use. Since the adapter is

isolated, the line cord does not need to be

equipped with a terminal for connection to

protective ground. Since line cords with a

protective grounding terminal are more

commonly available you might consider using

these anyhow.

Warning

To avoid electrical shock or fire if a test tool

input is connected to more than 42 V peak (30

Vrms) or on circuits of more than 4800 VA:

•Use only insulated voltage probes, test leads

and adapters supplied with the test tool, or

indicated by Fluke as suitable for the Fluke

19xC-2x5C ScopeMeter series.

•Before use, inspect voltage probes, test leads

and accessories for mechanical damage and

replace when damaged.

•Remove all probes, test leads and

accessories that are not in use.

•Always connect the battery charger first to

the ac outlet before connecting it to the test

tool.

•Do not connect the ground spring (Figure 1,

item f) to voltages higher than 42 V peak (30

Vrms) from earth ground.

•Do not apply input voltages above the rating

of the instrument. Use caution when using 1:1

test leads because the probe tip voltage will

be directly transmitted to the test tool.

•Do not use exposed metal BNC or banana

plug connectors.

Getting Started

Safety Information: Read First

•Do not insert metal objects into connectors.

•Always use the test tool only in the manner

specified.

Max. Input Voltages

Input A and B directly ...............................300 V CAT III

Input A and B via 10:1 probe ................... 1000 V CAT II

600 V CAT III

METER/EXT TRIG inputs........................ 1000 V CAT II

600 V CAT III

Max. Floating Voltage

From any terminal to earth ground ..........1000 V CAT II

600 V CAT III

Between any terminal .............................. 1000 V CAT II

600 V CAT III

Voltage ratings are given as “working voltage”. They

should be read as Vac-rms (50-60 Hz) for AC sinewave

applications and as Vdc for DC applications.

Measurement Category III refers to distribution level and

fixed installation circuits inside a building.

Measurement Category II refers to local level, which is

applicable for appliances and portable equipment.

The terms ‘Isolated’ or ‘Electrically floating’ are used in this

manual to indicate a measurement in which the test tool

input BNC or banana jack is connected to a voltage

different from earth ground.

The isolated input connectors have no exposed metal and

are fully insulated to protect against electrical shock.

The red and gray BNC jacks, and the red and black

4-mm banana jacks can independently be connected to a

voltage above earth ground for isolated (electrically

floating) measurements and are rated up to 1000 Vrms

CAT II and 600 Vrms CAT III above earth ground.

If Safety Features are Impaired

Use of the test tool in a manner not specified may

impair the protection provided by the equipment.

Before use, inspect the test leads for mechanical damage

and replace damaged test leads!

Whenever it is likely that safety has been impaired, the

test tool must be turned off and disconnected from the line

power. The matter should then be referred to qualified

personnel. Safety is likely to be impaired if, for example,

the test tool fails to perform the intended measurements or

shows visible damage.

Fluke 19xC-2x5C

Getting Started

Preparing for Use

At delivery, the installed NiMH batteries may be empty and

must be charged for 4 hours (with the test tool turned off)

to reach full charge:

•use only the Fluke Battery Charger/Power Adapter

model BC190

•before use check that the BC190 voltage and

frequency range match the local line power range

•connect the battery charger to the ac outlet

•connect the battery charger to the appropriate input on

the test tool near Input B.

Caution

To prevent decrease of the battery capacity, you

must charge the batteries at least once a year.

Powering/Resetting the Test Tool

Turning power on/off:

The test tool powers up in its last setup

configuration.

Resetting the test tool to the factory settings:

Turn power off, then press and hold the

USER key and turn on. You should

hear a double beep.

How to Navigate a Menu (example)

Display the input A function key labels.

Show the Input A (input A) menu.

The menu example shows that the input A signal is

displayed non-inverted (Normal) with full bandwidth (Full).

To let input A invert the input signal, and to limit the

bandwidth to 20 MHz do the following:

Highlight Inverted (inverted).

Accept Inverted + jump to the next field.

Highlight 20 MHz.

Accept 20 MHz + exit the menu.

Hiding a menu or key label:

Press the CLEAR MENU key.

Getting Started

Changing the Information Language

During operation of the test tool messages may appear on

the screen (for instance if you select a recorder function).

You can select the language in which messages will be

displayed.

Display the USER key labels.

Open the LANGUAGE menu to select a

language.

Adjusting Contrast and Brightness

Display the USER key labels.

Enable the arrow keys for adjustment.

Adjust the contrast of the screen.

Change the backlight brightness.

Using the Scope

Connect the probe(s) as shown in figure 2.

Figure 2. Scope Connections

AUTO- MANUAL ranging

After an Auto Set the trace position, range, time base and

triggering will be automatically adjusted to assure a stable

display of virtually any waveform.

Perform an Auto Set or select Manual

ranging (toggle). AUTO or MANUAL appears

at the top right of the screen.

Use the light-gray RANGE, TIME and MOVE keys to

change the view of the waveform manually.

Fluke 19xC-2x5C

Getting Started

Scope Readings and Waveforms

Automatic scope measurement results are shown as

Reading 1 (READING 1) and Reading 2 (READING 2) at the

upper left and right display edge.

Scope readings on (ON) or off (OFF).

on A : Reading 1 (2) is input A result.

on B : Reading 1 (2) is input B result.

V ac ...dB: measurement function.

Glitch Detect: glitch capture on or off.

Average: waveform averaging on or off.

Waveform:

Normal : normal waveform display.

Persistence... : waveform persistence.

□Digital Persistence: persistence off,

short, medium, long, infinite.

□Envelope: envelope on, off.

□Dot-join: dot join on or off

Mathematics... : A+B, A-B, AxB, A vs B (XY

mode), Spectrum (frequency spectrum

FFT).

Reference... : compare waveforms,

pass/fail testing.

Autres manuels pour ScopeMeter 225C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke 374 Manuel utilisateur

Fluke

Fluke 741B Manuel utilisateur

Fluke

Fluke 96000 Series Manuel utilisateur

Fluke

Fluke 1.4 MPA PPC4E Manuel utilisateur

Fluke

Fluke 321 Manuel d'utilisation et d'entretien

Fluke

Fluke 5790B Manuel utilisateur

Fluke

Fluke 1550 Manuel utilisateur

Fluke

Fluke 5790A Manuel utilisateur

Fluke

Fluke FiberInspector Pro FI-3000 Manuel utilisateur

Fluke

Fluke 368 Manuel d'utilisation et d'entretien

Fluke

Fluke 725 Manuel utilisateur

Fluke

Fluke 374 FC Manuel utilisateur

Fluke

Fluke 434/PWR Manuel utilisateur

Fluke

Fluke 9000A-006 Manuel utilisateur

Fluke

Fluke 095969674225 Manuel utilisateur

Fluke

Fluke QA-ES III Manuel de la liste des pièces

Fluke

Fluke 381 Manuel utilisateur

Fluke

Fluke LinkSprinter 100 Manuel utilisateur

Fluke

Fluke 434-II Guide de configuration

Fluke

Fluke Comark Diligence 600 Manuel utilisateur

Fluke

Fluke NORMA 6003 Manuel utilisateur

Fluke

Fluke 353 Manuel utilisateur

Fluke

Fluke 481 Manuel utilisateur

Fluke

Fluke 345 Manuel d'instructions

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur