FLIR EM54 Manuel utilisateur

Quick Start

FLIR EM54

Environmental Meter

EM54-QS-en-US_AA

EM54 - QUICK START - EN

Air Temperature, RH, Wet Bulb, Dew Point Modes

1. Long press to switch the meter ON/OFF

2. Short press VEL|TEMP|TYPE-K to step to Air Temperature mode (TEMP).

The upper digits show the reading, short press to toggle oC/oF

3. Short press %RH|FLOW to select RH for display on the lower digits

4. Short press WB|DP to toggle Wet Bulb (WB) and Dew Point (DP)

temperature modes. The upper digits show the reading

5. The temperature and RH sensors are located at the tip of the meter

6. For out of range measurements the display shows ‘OL’

Type-K Contact Temperature Measurements

1. Connect a thermocouple to the jack in the right-side compartment

2. Short press VEL|TEMP|TYPE-K to step to the TYPE-K mode

3. Touch the temperature probe to the surface under test, the upper display

digits show the reading. Short press to select oC/oF units

4. With no thermocouple connected the display shows dashes

5. See the Setup Mode section for setting a temperature display offset

Air Velocity Measurements

1. Connect the supplied vane anemometer probe to the USB jack in the right-

side compartment

2. Short press VEL|TEMP|TYPE-K to step to the Air Velocity mode (VEL)

3. Place the vane in the flow of air and view the air velocity readings on the

upper display digits

4. Short press to select the units m/s, ft/min, km/hr, MPH, or knots

Airflow (CFM, CMM) Measurements

1. Measure the area of the air duct under test. See Area Equations section

2. Connect the vane anemometer to the USB jack in the side compartment

3. Short press %RH|FLOW to select FLOW. Press to select CFM (cubic feet

per minute) or CMM (cubic meters per minute) for the volume (airflow)

measurement units

EM54-QS-en-US_AA

4. Long press the SETUP button to access the Setup Mode and then press 4

times to step to the AREA screen

5. Press Return ( ) and use the arrows ( ) to select the area units: in2,

cm2, or ft2

6. Press Return to access the SIZE screen. Press Return again and use the

arrows to select the decimal placement for the area value (note the x10 and

x100 multipliers on the display)

7. Press Return and use the arrows to adjust the flashing digit for the area

value. Use the Hbutton to select a new digit to edit. Continue in this way

until the area of the duct is accurately entered

8. Press Return to confirm the area value and then long press SETUP to exit

9. Insert the vane sensor in the air duct and read the airflow (volume of air)

value on the lower display digits

Setup Mode

1. Long press the SETUP button*

2. The first screen is the default TEMP UNIT for air temperature. Press Return

to see the setting. Use the arrows to set oC or oF

3. Press Return to see TYPE K OFFSET. Press Return again and use the arrows

to select a temperature offset, if desired

4. Press Return to see VEL UNITS. Press Return again to see the default units.

Use the arrows to select m/s, ft/min, km/hr, MPH, or knots

5. Press Return to see FLOW UNITS. Press Return again to see the default

Airflow units; use the arrows to select CFM or CMM

6. Press Return to see AREA UNIT. Press Return again to see the default area

units and use the arrows to change to in2, cm2, or ft2

7. Press Return to see AREA SIZE, press Return again and use the arrows to

select the decimal position for the area value. Press Return and use the

arrows to adjust the flashing digit. Use the Hbutton to select a new digit to

edit. Continue in this way until the area of the duct is accurately entered

8. Press Return to see SLP (sleep). Press Return to see the default APO time.

Use the arrows to set timer to 5, 10, 15, 20, 25, 30, 40, 60 minutes or OFF

9. Long press the SETUP button to exit the Setup Mode

*Note that you can use the arrow buttons immediately after you access the

Setup Mode to step through the Setup parameters quickly.

EM54-QS-en-US_AA

Area Equations

CFM (ft3/min) = Air Velocity (ft/min) x Area (ft2)

CMM (m3/min) = Air Velocity (m/sec) x Area (m2) x 60

Battery Replacement

Switch the meter OFF and remove the screw that secures the rear battery

compartment. Open the compartment and replace the 9V battery, observing

correct polarity. Re-assemble the meter before use.

LCD Backlight

Short press the backlight button to switch the backlight ON/OFF.

Data Hold

Short press H to access/exit the Data Hold mode. Data Hold freezes the

displayed reading. The HOLD icon will appear while in the Data Hold mode.

MAX-MIN-AVG Recording

Short press MAX|MIN|AVG to start recording (REC) and to step through

maximum, minimum, and average readings. Long press MAX|MIN|AVG to exit.

3-Year Limited Warranty

This product is protected by FLIR’s 3-Year Limited Warranty. Visit

www.flir.com/testwarranty to read the 3-Year Limited Warranty document.

extension.

User Manual

Visit https://support.flir.com (download tab) to download the User Manual

and Quick Start with translations. The User Manual includes detailed

specifications and instructions.

EM54-QS-en-US_AA

Corporate Headquarters

FLIR Systems, Inc.

2770 SW Parkway Avenue

Wilsonville, OR 97070 USA

Customer Support

Repair, Calibration, and Technical Support

https://support.flir.com

Publication Identification No.: EM54-QS

Release version: AA

Release Date: March 2019

Language: en-US

www.flir.com

Autres manuels pour EM54

Table des matières

Autres manuels FLIR Instrument de mesure

FLIR

FLIR CM275 Manuel utilisateur

FLIR

FLIR VP50 Manuel utilisateur

FLIR

FLIR ME13552 Manuel utilisateur

FLIR

FLIR CM42 Manuel utilisateur

FLIR

FLIR TA72 Manuel utilisateur

FLIR

FLIR VS80 KIT Manuel utilisateur

FLIR

FLIR CM57-2 Manuel utilisateur

FLIR

FLIR IGM CM275 Manuel utilisateur

FLIR

FLIR EXTECH HDV-TX1 Dimensions

FLIR

FLIR Extech Instruments RH520A Manuel utilisateur

FLIR

FLIR VS80C10-25RM Manuel utilisateur

FLIR

FLIR EXTECH INSTRUMENTS PQ34-12 Manuel utilisateur

FLIR

FLIR Imaging Moisture Meter Plus IGM MR176 Manuel utilisateur

FLIR

FLIR DM284 Manuel utilisateur

FLIR

FLIR CM72 Manuel utilisateur

FLIR

FLIR DM284 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX1 Dimensions

FLIR

FLIR CM94 Manuel utilisateur

FLIR

FLIR Extech Instruments 380193 Manuel utilisateur

FLIR

FLIR MR59 Manuel de l'opérateur

FLIR

FLIR Extech PQ3450-30 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR Extech Instruments MA410 Manuel utilisateur

FLIR

FLIR Extech Instruments RH520A-240 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur