FLIR CM174 Manuel utilisateur

USER MANUAL

FLIR CM174

IMAGING CLAMP METER with IGMTM

TRUE RMS 600A AC/DC CLAMP METER

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

Table of Contents

1. DISCLAIMERS 4

1.1 Copyright 4

1.2 Quality Assurance 4

1.3 Documentation 4

1.4 Disposal of Electronic Waste 4

2. SAFETY 4

3. INTRODUCTION 7

3.1 Key Features 7

4. METER DESCRIPTION 8

4.1 Meter Parts 8

4.2 Function Switch 9

4.3 Function Buttons 9

4.4 Display Icons and Indicators 10

4.5 Thermal Image Display 12

4.6 Clamp Meter Display 12

5. OPERATION 13

5.1 Powering the Meter 13

5.1.1 Auto Power Off 13

5.2 Auto/Manual Range Mode 13

5.3 HOLD Mode 13

5.4 Voltage and Current Measurements 14

5.4.1 Basic Voltage Measurements 14

5.4.2 ‘Lo Z’ Voltage Measurements 14

5.4.3 Basic Current Measurements 15

5.4.4 Extended Functionality Modes 16

5.5 Resistance Measurements 19

5.6 Continuity Test 19

5.7 Capacitance Measurements 20

5.8 Diode Test (CLASSIC mode) 21

5.9 Diode Test (SMART mode) 22

5.10 IGM Thermal Imager 23

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

5.10.1 Thermal Imager Basics 23

5.10.2 Programming Menu 25

5.10.3 Infrared Energy and Imaging Theory 28

6. MAINTENANCE 30

6.1 Cleaning and Storage 30

6.2 Battery Replacement 30

6.2.1 Disposal of Electronic Waste 30

7. SPECIFICATIONS 31

7.1 General specifications 31

7.2 IR Thermal Imaging Specifications 32

7.3 Electrical specifications 33

8. TECHNICAL SUPPORT 36

9. WARRANTY 37

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

1. Disclaimers

1.1 Copyright

including source code may be reproduced, transmitted, transcribed or translated into

any language or computer language in any form or by any means, electronic, magnetic,

optical, manual or otherwise, without the prior written permission of FLIR Systems.

The documentation must not, in whole or part, be copied, photocopied, reproduced,

translated or transmitted to any electronic medium or machine readable form without

prior consent, in writing, from FLIR Systems.

Names and marks appearing on the products herein are either registered trademarks or

trademarks of FLIR Systems and/or its subsidiaries. All other trademarks, trade names or

company names referenced herein are used for identification only and are the property

of their respective owners.

1.2 Quality Assurance

The Quality Management System under which these products are developed and

manufactured has been certified in accordance with the ISO 9001 standard.

FLIR Systems is committed to a policy of continuous development; therefore we reserve

the right to make changes and improvements on any of the products without prior

notice.

1.3 Documentation

To access the latest manuals and notifications, go to the Download tab at:

http://support.flir.com. It only takes a few minutes to register online. In the download

area you will also find the latest releases of manuals for our other products, as well as

manuals for our historical and obsolete products.

1.4 Disposal of Electronic Waste

As with most electronic products, this equipment must be disposed of in an

environmentally friendly way, and in accordance with existing regulations for

electronic waste.

Please contact your FLIR Systems representative for more details.

2. Safety

Safety Notes

Before operating the device, you must read, understand, and follow all instructions,

dangers, warnings, cautions, and notes.

FLIR Systems reserves the right to discontinue models, parts or accessories, and other

items, or to change specifications at any time without prior notice.

Remove the batteries if the device is not used for an extended period of time.

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

Warning Statements

Do not operate the device if you do not have the correct knowledge. Formal

qualifications and/or national legislation for the electrical inspections can apply. Incorrect

operation of the device can cause damage, shock, injury or death to persons.

Do not start the measuring procedure before you have set the function switch to the

correct position. This can cause damage to the instrument and can cause injury to

persons.

Do not change to current or resistance when you measure the voltage. This can cause

damage to the instrument and can cause injury to persons.

Do not measure the current on a circuit when the voltage increases to more than 1000 V.

This can cause damage to the instrument and can cause injury to persons.

You must disconnect the test leads from the circuit that you did a test on before you

change the range. If you do not do this, damage to the instrument and injury to persons

can occur.

Do not replace the batteries before you remove the test leads. This can cause damage to

the instrument and can cause injury to persons.

Do not use the device if the test leads and/or the device show signs of damage. Injury to

persons can occur.

Be careful when taking measurements if the voltages are more than 25 VAC rms or 35

VDC. There is a risk of shock from these voltages. Injury to persons can occur.

Do not do diode, resistance or continuity tests before you have removed the power from

capacitors and other devices under test during a measurement. Injury to persons can

occur.

Make sure that children cannot touch the device. The device contains dangerous objects

and small parts that children can swallow. If a child swallows an object or a part, speak

with a physician immediately. Injury to persons can occur.

Do not let children play with the batteries and/or the packing material. These can be

dangerous for children if they use them as toys.

Do not touch expired or damaged batteries without gloves. Injury to persons can occur.

Do not cause a short circuit of the batteries. This can cause damage to the instrument

and can cause injury to persons.

Do not put the batteries into a fire. Injury to persons can occur.

Cautions

Do not use the device for a procedure that it is not intended for. This can cause damage to the

protection.

This symbol, adjacent to another symbol or terminal, indicates that the user

must refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous

voltages may be present.

Double insulation.

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

UL listing is not an indication or a verification of the accuracy of the meter

IEC 60825-1 Ed. 2 (2007)

CAUTION: Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

Agency Approvals

(MSIP-REI-FS5-CM174)

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

3. Introduction

Thank you for selecting the FLIR CM174 Clamp Meter. The CM174 is a True RMS 600A

AC/DC clamp meter with radiometric Lepton Thermal Imaging system, integrated VFD

Mode, Inrush Current capture and a Lo Z mode for eliminating ‘ghost’ voltages. This

device is shipped fully tested and calibrated and, with proper use, will provide years of

reliable service.

3.1 Key Features

6000-count color TFT display

IGMTM (Infrared Guided Measurement) Thermal Imaging System

Work lights

Auto Range True RMS AC/DC 600 A capability

Auto Range True RMS AC/DC 1000 V capability

Frequency AC bandwidth (45-400Hz)

Frequency Measurements to 60KHz

Flex Clamp adaptor input for FLIR TA72_TA74 Clamp adaptors

Resistance and Continuity measurements

Capacitance and Diode measurements

Data HOLD

Inrush current

DCA zero function

Low Z (Impedance) mode

Minimum/Maximum memory

Integrated VFD mode (Low-pass filter)

Auto power off (can be deactivated or preset to 1, 2, 5, or 10 minutes)

Jaw opening 35mm (1.38”)

Easy-access battery cover mechanism

Safety Category Rating: CAT IV-600V, CAT III-1000V

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

4. Meter Description

4.1 Meter Parts

1. Jaw opening trigger

2. MODE/Hz/up arrow button

3. VFD/Work light/down arrow button

4. Function switch

5. COM (negative -) Probe Input jack

6. Positive (+) Probe Input jack

7. IGM Thermal Image mode button

8. DCA Zero/Inrush/OK button

9. MIN/MAX HOLD button

10. AUTO/RANGE Button

11. Color TFT Display

12. Clamp jaw

1. Work light

2. Thermal imaging lens

3. Tripod mount

4. Warning & informational text

5. Battery compartment

6. Battery compartment lock

7. Laser pointer lens

Fig 4-1 Front View

Fig 4-2 Rear View

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

4.2 Function Switch

Select this position when connecting a FLIR Flex Clamp Adaptor.

Select this position to measure in the low impedance mode.

Select this position to switch the meter OFF (full power saving mode).

Select this position to measure AC/DC Voltage through the probe

inputs.

The meter can measure resistance and continuity through the probe

inputs. The type of measurement is selected by the MODE button.

The meter can measure capacitance and diode through the probe

inputs. The type of measurement is selected by the MODE button.

Amps AC/DC. The meter can measure current through the clamp jaws.

4.3 Function Buttons

Select AC or DC in the Voltage/Current modes.

Select Diode or Capacitance; Continuity or Resistance.

Select Hz in AC Voltage, Current, or FLEX modes. Use ‘up’arrow in

menus.

Select Auto or Manual range mode, see section 5.3 Auto/Manual range

mode

In Manual mode, press to change the range (scale); to return to Auto

range mode from Manual mode, press and hold for > 2 seconds.

Toggle normal and Data Hold modes, see section 5.4 Hold mode

Press for > 2 seconds to activate/deactivate MIN/MAX mode.

Use as RETURN/BACK button in menus.

Press to activate/deactivate VFD mode.

Press and hold for > 2 seconds to switch the Work Light ON/OFF.

Use ‘down’arrow in menus.

Press to enter or exit the IGM Thermal Image mode.

Press and hold for > 2 seconds to access the Programming Menu.

FLIR CM174 USER MANUAL Document Identifier: CM174-en-US_AC

In the DCA mode, press to zero the display. In the ACA mode press to

activate or deactivate inrush current mode. Use to confirm (OK) menu

items.

4.4 Display Icons and Indicators

Indicates that the meter is displaying maximum reading values.

Indicates that the meter is displaying minimum reading values.

Indicates that the meter is in Auto range mode.

Indicates that the meter is in Hold mode.

Indicates the battery voltage status.

Indicates that the auto power off function is enabled.

Indicates that the measured voltage is greater than 30 V DC or AC RMS.

Indicates that the meter is measuring AC current or voltage.

Indicates that meter is measuring DC current or voltage.

Indicates that the continuity function is active.

Indicates that the diode test function is active.

Ohm symbol. Unit of measure for Resistance and Continuity.

Unit of measure for current (Amps or Amperes).

Volt. Unit of measure for Voltage.

Farad. Unit of measure for Capacitance.

Hertz. Unit of measure for Frequency.

103 (kilo)

10-3 (milli)

Autres manuels pour CM174

Table des matières

Autres manuels FLIR Instrument de mesure

FLIR

FLIR CM94 Manuel utilisateur

FLIR

FLIR MR59 Manuel utilisateur

FLIR

FLIR TA72 Manuel utilisateur

FLIR

FLIR Extech Instruments RH520A Manuel utilisateur

FLIR

FLIR MR176 Manuel utilisateur

FLIR

FLIR CM275 Manuel utilisateur

FLIR

FLIR VS80C10-25RM Manuel utilisateur

FLIR

FLIR Extech Instruments EN300 Manuel utilisateur

FLIR

FLIR EXTECH SDL310 Manuel utilisateur

FLIR

FLIR MR04 Manuel utilisateur

FLIR

FLIR Extech Instruments MA150 Manuel utilisateur

FLIR

FLIR CM72 Manuel utilisateur

FLIR

FLIR MR7 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX1 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR CM174 Manuel utilisateur

FLIR

FLIR CM85 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR Extech Instruments MA410 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX2 Dimensions

FLIR

FLIR Extech Instruments RH520A-240 Manuel utilisateur

FLIR

FLIR CM42 Manuel utilisateur

FLIR

FLIR CM78 Manuel utilisateur

FLIR

FLIR MR59 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur