FieldServer Genisys FS-8700-133 Note de version

A Sierra Monitor Company

APPLICABILITY & EFFECTIVITY

Effective for all systems manufactured after January 2009

Driver Manual

(Supplement to the FieldServer Instruction Manual)

FS-8700-133 Genisys

Driver Version:

1.01

Document Revision:

FS-8700-133 Genisys Manual Table of Contents

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

TABLE OF CONTENTS

1GENISYS DESCRIPTION ............................................................................................................................. 3

2DRIVER SCOPE OF SUPPLY ........................................................................................................................ 3

2.1 Supplied by FieldServer Technologies for this driver........................................................................................ 3

3HARDWARE CONNECTIONS ...................................................................................................................... 4

4DATA ARRAY PARAMETERS ...................................................................................................................... 5

5CONFIGURING THE FIELDSERVER AS A GENISYS CLIENT.............................................................................. 6

5.1 Client Side Connection Descriptions .................................................................................................................. 6

5.2 Client Side Node Descriptors .............................................................................................................................. 7

5.3 Client Side Map Descriptors................................................................................................................................ 8

5.3.1 FieldServer Related Map Descriptor Parameters ...................................................................................... 8

5.3.2 Driver Related Map Descriptor Parameters............................................................................................... 8

5.3.3 Timing Parameters...................................................................................................................................... 8

5.4 Map Descriptor Example: Read Indications....................................................................................................... 9

5.5 Map Descriptor Example: Write Controls........................................................................................................ 10

6CONFIGURING THE FIELDSERVER AS A GENISYS SERVER............................................................................11

APPENDIX A. USEFUL FEATURES......................................................................................................................12

Appendix A.1. Storage Structure for Data Type Bit and Byte ..................................................................................... 12

APPENDIX B. REFERENCE ................................................................................................................................13

FS-8700-133 Genisys Manual Page 3 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

1GENISYS DESCRIPTION

The Genisys driver allows the transfer of data to and from devices over RS-232 Genisys protocol. Vital Harmon

Logic Controller (VHLC) supports Genisys protocol. IM-188 VHLC GENISYS SOFTWARE MANUAL 100188-008

AB0.PDF is the basis of the Genisys driver. The FieldServer can be configured as a Client. Limited Server side

functionality has been implemented for FieldServer’s quality assurance requirements only.

Max Nodes Supported

FieldServer Mode

Nodes

Comments

Client

Only 1 virtual client per port allowed on multidrop systems.

Server

255

Maximum device addresses pollable by Client –protocol limitation.

2DRIVER SCOPE OF SUPPLY

2.1 Supplied by FieldServer Technologies for this driver

FieldServer Technologies PART #

Description

FS-8915-10

UTP cable (7 foot) for RS-232 use

FS-8917-04

RJ45 to DB25F connector adapter

FS-8700-133

Driver Manual.

FS-8700-133 Genisys Manual Page 4 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

3HARDWARE CONNECTIONS

The FieldServer is connected to the VHLC as shown in the following connection drawing.

Port C VHLC RS-232

Interface Module

DB25F

VHLC

Server

RJ45

FieldServer

GND

FS-8915-10

8917-04

FieldServer

RJ45

Connect to one of the RS-232

Ports on the FieldServer

FS-8700-133 Genisys Manual Page 5 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

4DATA ARRAY PARAMETERS

Data Arrays are “protocol neutral” data buffers for storage of data to be passed between protocols. It is necessary

to declare the data format of each of the Data Arrays to facilitate correct storage of the relevant data.

Section Title

Data_Arrays

Column Title

Function

Legal Values

Data_Array_Name

Provide name for Data Array

Up to 15 alphanumeric characters

Data_Array_Format

Provide data format. Each Data Array can only take

on one format.

FLOAT, BIT, UInt16, SInt16,

Packed_Bit, Byte, Packed_Byte,

Swapped_Byte

Data_Array_Length

Number of Data Objects. Must be larger than the

data storage area required by the Map Descriptors

for the data being placed in this array.

1-10, 000

Example

// Data Arrays

Data_Arrays

Data_Array_Name

, Data_Array_Format

, Data_Array_Length

DA_AI_01

, UInt16,

, 200

DA_AO_01

, UInt16

, 200

DA_DI_01

, Bit

, 200

DA_DO_01

, Bit

, 200

FS-8700-133 Genisys Manual Page 6 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

5CONFIGURING THE FIELDSERVER AS A GENISYS CLIENT

For a detailed discussion on FieldServer configuration, please refer to the FieldServer Configuration Manual. The

information that follows describes how to expand upon the factory defaults provided in the configuration files

included with the FieldServer (See “.csv” sample files provided with the FieldServer).

This section documents and describes the parameters necessary for configuring the FieldServer to communicate

with a Genisys Server.

The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable

the FieldServer for Genisys communications, the driver independent FieldServer buffers need to be declared in the

“Data Arrays” section, the destination device addresses need to be declared in the “Client Side Nodes” section, and

the data required from the Servers needs to be mapped in the “Client Side Map Descriptors” section. Details on

how to do this can be found below.

Note that in the tables, * indicates an optional parameter, with the bold legal value being the default.

5.1 Client Side Connection Descriptions

Section Title

Connections

Column Title

Function

Legal Values

Port

Specify which port the device is connected to the

FieldServer

P1-P81

Protocol

Specify protocol used

Genisys

Baud*

Specify baud rate

300 , 600, 1200, 2400, 4800, 9600 (Vendor

limitation)

Parity*

Specify parity

None, Even, Odd (Vendor limitation)

Data_Bits*

Specify data bits

8(Vendor limitation)

Stop_Bits*

Specify stop bits

1, 2 (Vendor limitation)

Handshaking*

Specify hardware handshaking

None

Poll_Delay*

Time between internal polls

0-32000 seconds, 0.05 seconds

Example

// Client Side Connections

Connections

Port

, Baud

, Data_Bits

, Stop_Bits

, Parity

, Protocol

, 9600

, 8

, 1

, None

, Genisys

Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction manual for details of the ports available

on specific hardware.

FS-8700-133 Genisys Manual Page 7 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

5.2 Client Side Node Descriptors

Section Title

Nodes

Column Title

Function

Legal Values

Node_Name

Provide name for Node

Up to 32

alphanumeric

characters

Node_ID

VHLC station address of physical Server Node

1-255

Protocol

Specify protocol used

Genisys

Connection

Specify which port the device is connected to the

FieldServer

P1-P81

Genisys_Check_Controls*

If OFF, the FieldServer configures VHLC to apply controls

from the FieldServer without verification.

If ON, the FieldServer configures VHLC to verify controls

supplied by the FieldServer before applying.

OFF, ON

Genisys_Intra_Poll_Delay*

Specify time, that FieldServer should wait before sending

ACK or Execute message after receiving the last character of

response from VHLC.

0.010s, 0.025s etc

Example

// Client Side Nodes

Nodes

Node_Name

, Node_ID

, Protocol

, Port

, Genisys_Check_Controls

, Genisys_Intra_Poll_Delay

Genisys_01

, 1

, Genisys

, P1

, ON

, 0.01s

Genisys_02

, 2

, Genisys

, P1

, -

, 0.01s

FS-8700-133 Genisys Manual Page 8 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

5.3 Client Side Map Descriptors

5.3.1 FieldServer Related Map Descriptor Parameters

Column Title

Function

Legal Values

Map_Descriptor_Name

Name of this Map Descriptor

Up to 32 alphanumeric characters

Data_Array_Name

Name of Data Array where data is to be

stored in the FieldServer

One of the Data Array names from “Data

Array” section above

Data_Array_Offset

Starting location in Data Array

0 to maximum specified in “Data Array”

section above

Function

Function of Client Map Descriptor

COS_Poller, COS_Read , Wrbx

5.3.2 Driver Related Map Descriptor Parameters

Column Title

Function

Legal Values

Node_Name

Name of Node to fetch data from

One of the Node names

specified in “Client Node

Descriptor” above

Data_Type*

‘Bit’ each byte of Indication statuses will be stored in 8

consecutive locations in the Data Array. Similarly while

writing; Control byte will be composed from 8

consecutive locations of the Dara Array.

‘Byte’ each byte of Indication statuses will be stored as

an 8-Bit Integer at the specified location. Similarly while

writing; Control byte will be composed from a single

location of the Data Array.

Refer to Appendix A.1

Bit, Byte

Address*

Internally used parameter, if used specify value 0

Length*

Length of Map Descriptor

Number of indications to store or number of controls to

write as per Data_Type.

Bit: 1-256, 8

Byte: 1-32, 1

Genisys_OnValue_Change*

If this parameter is set to Yes, the driver will only send

controls if there is a value change when the Data Array

is updated.

Yes, -

5.3.3 Timing Parameters

Column Title

Function

Legal Values

Scan_Interval

Rate at which data is polled

≥0.001s

FS-8700-133 Genisys Manual Page 9 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

5.4 Map Descriptor Example: Read Indications

The following Map Descriptors will read indication words from physical Server Genisys_01 and Genisys_02 (described in Client Side Node Descriptors section).

The Cos_Poller Map Descriptor polls VHLC for any indication word changes and returned data is stored on the Data Array under the COS_READ Map Descriptor

for the same Node. The rate of polling is determined by the Scan_Interval.

The Cos_Read Map Descriptor also polls VHLC for all indication words irrespective of data change. The rate of polling is determined by the Scan_Interval.

If Data_Type is Byte, any location in Data Array will hold one indication word from VHLC.

If Data_Type is Bit, eight consecutive locations in Data Array will hold one indication word from VHLC. Also see Appendix A.1.

// Client Side Map Descriptors

Map_Descriptors

Map_Descriptor_Name

, Scan_Interval

, Data_Array_Name

, Data_Array_Offset

, Function

, Node_Name

, Data_Type

, Address

, Length

CMD_01

, 1.00s

, DA_COS_01

, 0

, COS_Poller

, Genisys_01

, Byte

, 0

, 1

CMD_01a

, 50s

, DA_8I_01

, 0

, COS_Read

, Genisys_01

, Byte

, 0

, 32

CMD_02

, 1.00s

, DA_COS_02

, 0

, COS_Poller

, Genisys_02

, Bit

, 0

, 1

CMD_02a

, 50s

, DA_DI_01

, 0

, COS_Read

, Genisys_02

, Bit

, 0

, 256

Name of one of the Data

Arrays defined in the

Data_Array section.

Indication statuses will be

stored in this Data Array

Starting offset

in Data Array to

hold 1st

indication

status

One of the Nodes

declared in Node

Section. Indications

will be read from the

station address

belonging to this Node

Frequency (in

seconds) to read

Indication Statuses

Number of consecutive

locations in the Data array

to be used for storing data

from the Server.

FS-8700-133 Genisys Manual Page 10 of 13

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

5.5 Map Descriptor Example: Write Controls

The following Map Descriptor will write controls to physical Server Genisys_01 and Genisys_02 (described in Client Side Node Descriptors section) whenever

any of the control statuses changes/updates. One such Map Descriptor is required per Node.

If Data_Type is Byte, 32 consecutive locations from the Data Array will be written to VHLC. Data at any location would be considered as one control word.

If Data_Type is Bit, 256 consecutive locations from the Data Array will be written to VHLC. Data at 8 consecutive locations would be considered as one control

word.

Also see Appendix A.1.

// Client Side Map Descriptors

Map_Descriptors

Map_Descriptor_Name

, Scan_Interval

, Data_Array_Name

, Data_Array_Offset

, Function

, Node_Name

, Data_Type

, Address

, Length

CMD_01b

, -

, DA_8O_01

, 0

, Wrbx

, Genisys_01

, Byte

, 0

, 32

CMD_02

, -

, DA_DO_01

, 0

, Wrbx

, Genisys_02

, Bit

, 0

, 256

Name of one of

the Data Arrays

defined in

Data_Array

section. This

Data Array holds

control statuses

to be written to

other devices.

Starting offset

in the Data

Array which

holds the 1st

control status.

One of the

Nodes declared

in the Node

Section.

Indications will

read from the

station address

belonging to this

Node

Number of consecutive

locations in the Data

array to use when

issuing the Write

command.

Wrbx: send write command

to the Server when the

associated Controls updates

or changes. To write

continuously use Wrbc as the

function and add a

Scan_Interval parameter to

configure how often to write.

Table des matières

Autres manuels FieldServer Matériel réseau

FieldServer

FieldServer FS-8700-03 DF1 Note de version

FieldServer

FieldServer X-25 Guide de l'utilisateur

FieldServer

FieldServer FS-8700-74 Note de version

FieldServer

FieldServer FS-8704-09 SNMP Note de version

FieldServer

FieldServer Envirotronics SystemsPlus FS-8700-88 Note de version

FieldServer

FieldServer Omron FINS FS-8704-16 Note de version

FieldServer

FieldServer Gamewell FCI 7100 Series Note de version

FieldServer

FieldServer FS-8700-72 Manuel utilisateur

FieldServer

FieldServer Lutron Machine FS-8700-97 Note de version

FieldServer

FieldServer Weigh-Tronix FS-8700-36 Note de version

FieldServer

FieldServer ProtoCessor ProtoNode FPC-N34 Guide de l'utilisateur

FieldServer

FieldServer Modbus Daniels FS-8700-15 Note de version

FieldServer

FieldServer FS-8704-06 Manuel utilisateur

FieldServer

FieldServer ControlNet FS-8700-24 Note de version

FieldServer

FieldServer Spectronics FS-8700-42 Note de version

FieldServer

FieldServer Carrier DataPort FS-8700-86 Note de version

FieldServer

FieldServer Modbus Plus FS-8700-02 Note de version

FieldServer

FieldServer Safetran SCS-128 FS-8700-128 Note de version

FieldServer

FieldServer Metasys N2 FS-8700-19 Note de version

FieldServer

FieldServer Telnet FS-8704-11 Note de version

FieldServer

FieldServer Profibus DP FS-8700-20 Note de version

FieldServer

FieldServer A Sierra Monitor Company FS-8700-122 Note de version

FieldServer

FieldServer Carrier DataLink FS-8700-82 Note de version

FieldServer

FieldServer Optomux FS-8700-17 Note de version

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur