FIC PA-2013 Manuel utilisateur

1

Installation Procedures

The motherboard has several user-adjustable jumpers on the board that allow

you to configure your system to suit your requirements. To set up your

computer, you should follow these installation steps To set up your computer,

you should follow these installation steps:

nStep 1 -

Set system jumpers

nStep 2 -

Install memory modules

nStep 3 -

Install the CPU

nStep 4 -

Install expansion cards

nStep 5 -

Connect cables and power supply

nStep 6 -

Set up BIOS feature

nStep 7 -

Set up supporting software utilities

CAUTION : If you use an electric drill to install this motherboard on your

chassis, please wear a static wrist strap. The recommended electric drill

torque is from 5.0 to 8.0 kg/cm to avoid damaging the chips’ pins.

Chapter 1

PA-2013 Motherboard Manual

2

Clear Password: CPS

This jumper allows you to enable or to disable the password configuration. You

may need to enable this jumper by shorting it with a jumper cap if you forget

your password. To clear the password setting: 1. Turn off your computer, (2).

Short this jumper by placing a jumper cap on it, (3) Turn on your computer,

(4), Hold down the Delete key during boot and enter BIOS Setup to re-enter

user preferences, (5) Turn off your computer, (6) Remove the jumper cap, (7)

Turn on your computer for the new settings to take effect.

Flash ROM Type Selection: EP1, EP2

These two jumpers allow you to configure the type of flash ROM chip. This

jumper setting is correct by manufactory default. If you want to know the flash

ROM type installed on this motherboard, remove the sticker from the chip to

see its type.

Installation Procedures

3

CPU to SRAM Data Transacting Mode Selection: SRAM

This jumper allows you to select the CPU to SRAM data read/write mode.

If you install a Cyrix or IBM processor on this motherboard, please set at 2-3

pin pair. Please also read Linear Burst feature of Chipset Features Setup,

Chapter 3 for more information.

PA-2013 Motherboard Manual

4

DIMM Frequency: CLK4,

SDRAM

System Frequency: NBCLK1,

NBCLK2

Installation Procedures

5

CPU External (BUS) Frequency: CLK1, CLK2, CLK3

The table below shows the jumper

settings for the different CPU

speed configurations.

NOTE: * when it selected, the system performance will not be guaranteed.

CPU to Bus Frequency Ratio: FREQ1, FREQ2, FREQ3

These three jumpers are used in combination to decide the ratio of the internal

frequency of the CPU to the bus clock.

PA-2013 Motherboard Manual

6

Set CPU Frequency

Model Freq. Bus Freq. Ratio

Intel Pentium MMX-233 233 66 3.5 x

Intel Pentium MMX-200 200 66 3 x

Intel Pentium MMX-166 166 66 2.5 x

Intel Pentium-200 200 66 3 x

Intel Pentium-166 166 66 2.5 x

Intel Pentium-133 133 66 2 x

Intel Pentium-100 100 66 1.5 x

AMD-K6-2-400* 400 100 4 x

AMD-K6-2-366* 366 66 5.5 x

AMD-K6-2-350 350 100 3.5 x

AMD-K6-2-333 333 95 3.5 x

AMD-K6-2-300 300 66 4.5 x

100 3 x

AMD-K6-300 300 66 4.5 x

AMD-K6-266 266 66 4 x

AMD-K6-233 233 66 3.5 x

AMD-K6-200 200 66 3 x

AMD-K6-166 166 66 2.5 x

AMD-K5-PR200 133 66 2 x

AMD-K5-PR166 116 66 1.75 x

AMD-K5-PR133 100 66 1.5 x

AMD-K5-PR100 100 66 1.5 x

Cyrix M II-350* 300 100 3 x

IBM 6x86MX-PR350* 291 83 3.5 x

300 75 4 x

Cyrix M II-333 266* 66* 4 x*

IBM 6x86MX-PR333 263* 75* 3.5 x*

250 83 3 x

250* 100* 2.5 x*

Cyrix M II-300 225 75 3 x

IBM 6x86MX-PR300 233 66 3.5 x

(be continued on the next page)

NOTE:

1. * This type of CPU was not available for testing at time of printing.

2. For most up-to-date information, please visit the FIC web site at

http://www.fic.com.tw.

Installation Procedures

7

(Continued from previous page)

Model Freq. Bus Freq. Ratio

Cyrix/IBM 6x86MX-PR266 208 83 2.5 x

Cyrix/IBM 6x86MX-PR233 166 83 2 x

188 75 2.5 x

Cyrix/IBM 6x86MX-PR200 166 66 2.5 x

150 75 2 x

Cyrix/IBM 6x86MX-PR166 133 66 2 x

Cyrix/IBM 6x86L-PR200+ 150 75 2 x

Cyrix/IBM 6x86L-PR166+ 133 66 2 x

Cyrix/IBM 6x86-PR200+ 150 75 2 x

Cyrix/IBM 6x86-PR166+ 133 66 2 x

IDT WinChip2-200 200 66 3 x

IDT WinChip-200 200 66 3 x

Set CPU Voltage

This section lists all possible CPU voltages that this board supports. There are

two rows of CPU voltage (core voltage) jumper setting in the diagram below.

NOTE: Please refer to your CPU top marking about the actual CPU voltage.

(It is core voltage, the IO voltage is 3.3V.)

PA-2013 Motherboard Manual

8

Installation Procedures

9

This Page Intentionally Left Blank

Autres manuels pour PA-2013

1

Autres manuels FIC Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur