Extron electronics FOX II T DP 4K Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

Unbalanced Stereo Output Balanced Stereo Output

Unbalanced Stereo Input Balanced Stereo Input

Do not tin the wires!

Tip

No Ground Here

Tip

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Tip

FOX II T/R DP 4K • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX II T/R DP 4K ber optic

extenders.

WARNING: These units output continuous invisible light, which may be harmful to the eyes; use with caution. For additional

safety, plug the attached dust caps into the optical transceivers when the fiber optic cable is unplugged.

CLASS 1 LASER PRODUCT, see the FOX II T/R DP 4K User Guide, at www.extron.com.

AVERTISSEMENT : Le FOX II T/R DP 4K émet une lumière invisible en continu (conforme à la classe1) qui peut être dangereux

pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque

le câble fibre optique est débranché.

Produit laser de classe1, voir le FOX II T/R DP 4K User Guide sur www.extron.com (en anglais).

Installation

FOX II DP 4K Transmitter Rear Panel

FOX II DP 4K Receiver Rear Panel

100-240V ~ -.-A MAX

50-60 Hz

DISPLAYPORT LOOP THRU

LRRS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G1 2

Tx Rx Tx RxG

AUDIO

INPUTS AUDIO

RETURN OUT

REMOTE

OVER

FIBER

FOX T DP 4K

100-240V ~ -.-A MAX

50-60 Hz

DISPLAYPORT

LRRS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G1 2

Tx Rx Tx RxG

AUDIO

OUTPUTS AUDIO

RETURN IN

REMOTE

OVER

FIBER

FOX R DP 4K

Step 1 — Mounting

Turn off or disconnect all equipment power

sources and mount the transmitter as required.

For mounting details and considerations, see the

FOX II T/R DP 4K User Guide at www.extron.com.

Step 2 — Input and Output Connections

a. Connect a DisplayPort

DISPLAYPORT LOOP THRU

video source to the

transmitter DisplayPort input connector.

b. If desired, connect a DisplayPort video display

to the transmitter Loop-Thru connector for a

local display.

c. Connect a DisplayPort video display to the receiver DisplayPort output connector.

DISPLAYPORT

d. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector

AUDIO

on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.

e. Connect an audio output device to either or both the 3.5 mm mini jack or the Audio 5-pole captive screw connector

on the receiver. See the drawing below step 2g to make connections on the captive screw connector.

f. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw

AUDIO

RETURN OUT

AUDIO

RETURN IN

connector on the transmitter. See the drawing below step 2g to make connections on the captive screw

connector.

g. For optional returned audio, connect an audio input device to the Audio Return In 5-pole captive screw

connector on the receiver. See the drawing below to make connections on the

captive screw connector.

ATTENTION:

• For unbalanced audio, connect the sleeves to the ground

contact. DO NOT connect the sleeves to the negative (-)

contacts.

• Pour l’audio asymétrique, connectez les manchons

au contact au sol. NE PAS connecter les manchons

aux contacts négatifs (–).

NOTE: For returned audio, above, you must also do the following:

• Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver.

• Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b.

FOX II T/R DP 4K • Setup Guide (Continued)

h. If you want the FOX II DP 4K units to pass serial or IR data or control signals, such as for serial

Rx TxGnd

Tx RxGnd

IR Device

RS-232 Device

RS-232 IR

Tx Rx Tx RxG

OVER

FIBER

control of a projector, connect the primary device to the transmitter and the controlled device to

the receiver via the Over Fiber 5-pole captive screw connectors on both units.

i. For remote monitoring of the status of the Rx optical link on either the transmitter or

RS-232 ALARM

Tx Rx G

REMOTE

receiver, connect a locally constructed or obtained device to the two rightmost poles

of the Alarm and Remote RS-232 5-pole captive screw connector on that unit. The

unit shorts both poles together when no light is detected.

NOTE: The transmitter port reports the status of the link from the receiver.

The receiver port reports the status of the link from the transmitter.

j. For remote control of a unit and for loading firmware, connect a host device, such as a computer or control system, to either of the

following ports on the unit to be controlled:

Configuration port — The front panel USB mini-B connector.

CONFIG

NOTE: Extron recommends performing firmware updates via the Configuration port only.

Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector.

RS-232 ALAR

Tx Rx G

REMOTE

The protocol for the Remote port is as follows:

• 9600 baud •no parity •8 data bits

• 1 stop bit •no flow control

Step 3 — Throughput Connections

Receiver

ransmitter

OPTICAL

LINK

OPTICAL

LINK

NOTE: See the two fiber cable connection drawings below. You can connect the transmitter to a compatible

receiver in one of two ways:

• One way (transmitter to receiver) only, perform step 3a.

• Two way (transmitter to receiver and return), perform steps 3a and 3b.

a. Connect the fiber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).

NOTE: Ensure that the transmitter and connected receiver are the same transmission mode,

singlemode (SM) or multimode (MM) and that you use the correct SM or MM fiber cable to connect the

devices

b. If you want the receiver to return serial data (such as responses from a controlled device), IR data, or returned audio

to the transmitter, connect a cable between the Tx port on the receiver and Rx port on the transmitter (2).

Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).

NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the

optical link.

Operation

After all receivers, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are

encountered, verify that the cables are routed and connected properly and that all display devices have identical resolutions and refresh

rates. If problems persist, call the Extron S3 Sales & Technical Support Hotline at the number that is closest to you. See the contact

numbers on the last page of this guide for the Extron ofce nearest you.

Indications

NOTE: The figure below right is of a receiver. A transmitter has similar indications.

Power ( ) LED — Indicates that power is applied to the unit.

CONFIG SIGNAL

VIDEO AUDIO

HDCP

OUTPUT

RETURN IN

Video LEDs —

Signal LED — Lights when the unit detects an input video signal.

HDCP LED — Lights when the input signal is HDCP encrypted.

Audio LEDs —

Input LED (transmitter) — Lights when an analog audio or PCM digital

audio signal remains above -35 dBV. The LED goes unlit if the audio

signal level drops below the threshold for 10 seconds or longer.

Output LED (receiver) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the

audio signal level drops below the threshold for 10 seconds or longer.

Return Out LED (transmitter) — Lights when analog audio is present on the transmitter Return Audio Output connector.

Return In LED (receiver) — Lights when analog audio is present on the receiver Return Audio Input connector.

EDID SELECT

EDID

EDID Minder switch — Set this switch to one of the positions at right to select the source of the DDC or a specic resolution.

Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS

command or the Product Conguration Software.

Position 1 — The EDID is selected via the

Remote or USB port, using an SIS command or

the Extron Product Conguration Software.

Position

2— Use the EDID from the display connected to

the receiver.

NOTE: EDID from the display connected

to the receiver requires connection of both

fiber cables.

Position 3 — Use the EDID from the display connected to the transmitter loop-through.

Positions 4 through E — Specify a resolution. The table at right identies the resolutions associated with the switch positions. All

resolutions are at 60 Hz with the exception of 4096x2160 (E), which is 30 Hz.

Position F — No EDID assigned.

Remote Control

See the FOX II T/R DP 4K User Guide, available at www.extron.com, for details on operating and monitoring the transmitter using either

SIS commands or the Extron Product Conguration Software.

Pos. Source or resolution Pos. Resolution Pos. Resolution

0 User recorded EDID 6 1366x768 C 2048x2160

1 Selected via RS-232 7 1440x900 D 2560x1600

2 Display on Rx output 8 1680x1050 E* 3840x2160

3 Display on Tx loop-through 9 1920x1080 F N/A

4 1280x720 A 1920x1200

5 1280x800 B 2048x1536

* 30 Hz

68-2540-50 Rev. C

11 20

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Application Diagram

STANDBY

CLASS2 WIRING

XPA1002

LEVEL

1212

LIMITER/

PROTECT

SIGNAL

INPUTS OUTPUT

REMOTE

VOL/MUTE

10V 50mA

100-240V 1.3A,50-60Hz

100-240V~ -.-AMAX

50-60 Hz

DISPLAYPORT

L R

RS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G 1 2

L R

Tx Rx Tx RxG

AUDIO

OUTPUTS

AUDIO

RETURN IN

REMOTE

OVER

FIBER

FOX R DP 4K

100-240V~ -.-AMAX

50-60 Hz

DISPLAYPORT LOOP THRU

L R

RS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G 1 2

L R

Tx Rx Tx RxG

AUDIO

INPUTS

AUDIO

RETURN OUT

REMOTE

OVER

FIBER

FOX T DP 4K

POWER

12V

--AMAX

Tx Rx RTSCTS

COM1

TxRx

COM2

VC G

VOL RELAYS

1 2 C

12 3 4 G

DIGITALI/O

PWR OUT = 6W

eBUS

+V +S -S G

LAN

IPCP PRO 250

IR/S

MODEL80

Extron

Help System

Off

Display

Room

Control

Off

Mute

Screen

Lighting

December15, 2013 - 7:58 AM

Audio

Control

Volume

Mute

Tuner

123

VCR

LaptopPC DVD Doc

Cam

Tuner

Channel

Last

Presets

Enter

RS-232

Ethernet

Audio

4K DisplayPort

Extron

SI 28

Surface-mount

Speakers

Extron

XPA 10

Power

Amplier

4K Display

Local

Monitor

Up to 30 km (18.75 miles)

Singlemode Fiber

SM Model

Audio

RS-232

Extron

FOX T DP 4K

Fiber Optic Transmitter

Extron

FOX R DP 4K

Fiber Optic Receiver

Extron

TLP Pro 72

7" Table Top

TouchLink Pro

Touchpanel

TCP/IP

Network

Extron

IPCP Pro 250

IP Link Pro

Control Processor

Autres manuels pour FOX II T DP 4K

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Émetteur

Extron electronics

Extron electronics DTP T USW 233 Manuel utilisateur

Extron electronics

Extron electronics FOXBOX 4G Tx Manuel utilisateur

Extron electronics

Extron electronics TP T 15HD AV Manuel utilisateur

Extron electronics

Extron electronics DTP3 T 101 D Manuel utilisateur

Extron electronics

Extron electronics XTP T UWP 202 Manuel utilisateur

Extron electronics

Extron electronics PVT CV Manuel utilisateur

Extron electronics

Extron electronics TP T 15HD 45 Manuel utilisateur

Extron electronics

Extron electronics XTP T HDMI Manuel utilisateur

Extron electronics

Extron electronics FOX T UWP 302 Manuel utilisateur

Extron electronics

Extron electronics FOX3 T 201 Manuel utilisateur

Extron electronics

Extron electronics DTP2 T 201 D Manuel utilisateur

Extron electronics

Extron electronics UCS FT 901 Manuel utilisateur

Extron electronics

Extron electronics DTP T HWP D Series Manuel utilisateur

Extron electronics

Extron electronics DTP3 T 203 Manuel utilisateur

Extron electronics

Extron electronics DTP T EU 232 Manuel utilisateur

Extron electronics

Extron electronics DTP T FB 332 Manuel utilisateur

Extron electronics

Extron electronics DTP2 T 202 FB Manuel utilisateur

Extron electronics

Extron electronics DTP3 T 203 Manuel utilisateur

Extron electronics

Extron electronics TP Series Manuel utilisateur

Extron electronics

Extron electronics MTP 15HD A Series Manuel utilisateur

Extron electronics

Extron electronics DTP2 T/R 211 Manuel utilisateur

Extron electronics

Extron electronics XTP T VGA Manuel utilisateur

Extron electronics

Extron electronics XTP T FB 202 Manuel utilisateur

Extron electronics

Extron electronics USB Extender Plus Series Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur