EPOX 3VCA Manuel utilisateur

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subjected to change without notice.

Manual Revision 1.0

October 28, 1999

3VCA

A CeleronTM Sockket 370 Processor

based 4X AGP motherboard (133/100/

66MHz)66MHz)

66MHz)

SupporSuppor

Supports PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Module

6VBA2

A PA P

A Pentiumentium

entiumentium

entium®®

®®

®II or PII or P

II or PII or P

II or Pentiumentium

entiumentium

entium®®

®®

®III Slot1III Slot1

III Slot1III Slot1

III Slot1

Processor based 4X AGP motherboard

(133/100/66MHz)(133/100/66MHz)

(133/100/66MHz)

SupporSuppor

Supports PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Module

Features3VCA/6VBA2

Page 2

FEATURES

3VCA/6VBA2 Features:

•3VCA is based on the Intel CeleronTMProcessor operating at 300 ~

600MHz on PGA370. The board is configured by an ESSJ (Easy-Setting-

Single-Jumper) to match your CPU clock speed.

•6VBA2 is based on the Pentium®II/III Processor operating at 266 ~

733MHz on Slot1. The board is configured by an ESSJ (Easy-Setting-

Single-Jumper) to match your CPU clock speed.

• Designed with VIA Apollo Pro 133A PCIset.

• Supports up to 768MB of DRAM (minimum of 8 MB) on board (please

see Section 3-2).

•3VCA/6VBA2 will support Error Checking and Correcting (ECC)

when using parity SDRAM memory modules. This will detect multiple bit

errors and correct 1-bit memory errors.

• Supports (1) 16 bit ISA slots, (5) 32 bit PCI slots, (1) 4X AGP slot, (1) AMR

slot and provides (2) independent high performance PCI IDE interfaces

capable of supporting PIO Mode 3/4 and Ultra DMA 33/66 devices.

The 6VBA2 supports (5) PCI Bus Master slots and a jumperless PCI

INT# control scheme which reduces configuration confusion when plugging

in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with on chip Multi I/O: (1) floppy port, (1) parallel port (EPP,

ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

Features 3VCA/6VBA2

Page 3

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com/

please visit our Technical Support section for the latest updates).

•3VCA/6VBA2 utilizes a Lithium battery which provides environmental

protection and longer battery life.

• Supports the (4) Universal Serial Bus (USB) Ports. The onboard

VT82C686A chip provides the means for connecting PC peripherals such

as; keyboards, joysticks, telephones, and modems.

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows®95/98.

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

• Resume by Alarm - Allows your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Keyboard power ON function (KBPO).

• Built-in WOL (Wake-up On Lan) Connector.

• Built-in WOM (Wake-up On Modem) Connector.

• Built-in AC97 PCI Audio.

Installation 3VCA/6VBA2

Page 4

3VCA Detailed Layout

Installation 3VCA/6VBA2

Page 5

6VBA2 Detailed Layout

Installation3VCA/6VBA2

Page 6

Easy Installation Procedure

The following must be completed before powering on your new system:

Configured Jumpers

System memory Configuration

Device Connectors

Configure Jumpers

We design this motherboard with the fewest jumpers to make your installation fast

and easy.

The following will describe all of the jumpers that you are required to set before

moving on to step 2.

1234

1WS)zHM(UPC

1234 oitaRzHM66zHM001zHM331

NONONOX3002003004

NONOX5.3332053764

NONONOX4662004335

NONOX5.4003054006

NONOX5333005766

NOX5.5663055337

NONONOX6004006008*

NONOX5.6334056*768*

NONOX7664007*

NOX5.7005057*

NONOX8335*008*

*reserved

JP1 Clear COMS

1-2 : Normal(default)

2-3 : Clear CMOS

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled(default)

2-3 : Enabled

SW1

Installation 3VCA/6VBA2

Page 7

System Memory Configuration

Memory Layout

The 3VCA/6VBA2 supports (3) PC133 168-pin DIMMs (Dual In-line

Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or

SDRAM (Synchronized DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using both

SIMM and DIMM.

* SDRAM only supports 8, 16, 32, 64, 128, 256MB DIMM modules.

* We recommend to use PC100 Memory Module for bus speed between 66MHz

and 100MHz and PC133 Memory for bus speed over 100MHz.

* Using non-compliant memory with higher bus speed (over clocking) may

severely compromise the integrity of the system.

DIMM 1

DIMM 2

Bank 0/1

Bank 2/3

DIMM 3

Bank 4/5

-Synchronous

-EDO

yromeMlatoT 1MMID )1/0knaB( 2MMID )3/2knaB( 3MMID )5/4knaB(

BM652= mumixaM

*MARDS/ODE ,BM46,BM23,BM61,BM8 1XBM652,BM821 enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821 enoN

BM867=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

Figure 2

Table 1

Installation 3VCA/6VBA2

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connec-

tions (figure 7).

J2,J3: Chassis Panel Connector

• Power LED, Speaker, Reset, Turbo LED, HDD LED, IR Conn., Sleep/

Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

J8: WOM (Wake On Modem) Connector

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD Audio Connector

AUX1: AUX Audio Connector

MODEM1: Telephony Connector

• Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem)

Figure 7

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Joystick/Midi port

Installation3VCA/6VBA2

Page 9

Device Connectors (continued)

(This is connected to the power button on the case. Using the Soft-Off

by Pwr-BTTN feature, you can choose either Instant Off (turns system

off immediately), or 4 sec delay (you need to hold the button down for

4 seconds before the system turns off). When the system is in 4 sec

delay mode, there is a special feature to make the system to go into

suspend mode when the button is pressed momentarily).

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks

is activate

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Power On/Off

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Power LED - Power LED connector

1. Power LED(+) 4. NC

2. N/C 5. GND

3. GND

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels EPOX Carte mère

EPOX

EPOX EP-8KTA Manuel utilisateur

EPOX

EPOX M762A Series Manuel utilisateur

EPOX

EPOX IP-4PCI2E Series Manuel utilisateur

EPOX

EPOX P55-KV Manuel utilisateur

EPOX

EPOX KP6-LA Manuel utilisateur

EPOX

EPOX EP-MVP3G-M Manuel utilisateur

EPOX

EPOX KP6-LS Manuel utilisateur

EPOX

EPOX EP-3S1M Manuel utilisateur

EPOX

EPOX P2-133A Manuel utilisateur

EPOX

EPOX MVP4A Manuel utilisateur

EPOX

EPOX nForce2 Ultra 400 Manuel utilisateur

EPOX

EPOX EP-3VWM Manuel utilisateur

EPOX

EPOX EP-V370Y Manuel utilisateur

EPOX

EPOX EP-MVP3G-M Manuel utilisateur

EPOX

EPOX 6WEA4I Manuel utilisateur

EPOX

EPOX EP-8NPAJ Manuel utilisateur

EPOX

EPOX 3WXA Manuel utilisateur

EPOX

EPOX EP-6ZXM Manuel utilisateur

EPOX

EPOX EP-5P945-J3 Manuel utilisateur

EPOX

EPOX KP6-LS Manuel utilisateur

EPOX

EPOX ProNiX EP-9NPAJ Manuel utilisateur

EPOX

EPOX LX370Y Manuel utilisateur

EPOX

EPOX P55-TX 2 Manuel utilisateur

EPOX

EPOX EP-8RDAE Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur