Endress+Hauser HART iTEMP TMT182B Manuel utilisateur

Products Solutions Services

Operating Instructions

iTEMP TMT182B

Temperature transmitter

BA02260T/09/EN/01.22-00

71590122

2022-08-30

About this document iTEMP TMT182B

2 Endress+Hauser

1 About this document

1.1 Document function

These Operating Instructions contain all the information required in the various life cycle

phases of the device: from product identification, incoming acceptance and storage, to

installation, connection, operation and commissioning, through to troubleshooting,

maintenance and disposal.

1.2 Safety instructions (XA)

When using in hazardous areas, compliance with national regulations is mandatory.

Separate Ex-specific documentation is provided for measuring systems that are used in

hazardous areas. This documentation is an integral part of these Operating Instructions.

The installation specifications, connection data and safety instructions it contains must be

strictly observed! Make sure that you use the right Ex-specific documentation for the right

device with approval for use in hazardous areas! The number of the specific Ex

documentation (XA...) is provided on the nameplate. If the two numbers (on the Ex

documentation and the nameplate) are identical, then you may use this Ex-specific

documentation.

1.3 Symbols used

1.3.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.3.2 Electrical symbols

Symbol Meaning

Direct current

Alternating current

Direct current and alternating current

iTEMP TMT182B About this document

Endress+Hauser 3

Symbol Meaning

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a

grounding system.

Potential equalization connection (PE: protective earth)

Ground terminals that must be connected to ground prior to establishing any other

connections.

The ground terminals are located on the interior and exterior of the device:

• Interior ground terminal: potential equalization is connected to the supply network.

• Exterior ground terminal: device is connected to the plant grounding system.

1.3.3 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Preferred

Procedures, processes or actions that are preferred.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation

Reference to page

Reference to graphic

Notice or individual step to be observed

… Series of steps

Result of a step

Help in the event of a problem

Visual inspection

1.3.4 Symbols in graphics

Symbol Meaning Symbol Meaning

1, 2, 3,... Item numbers

… Series of steps

A, B, C, ... Views A-A, B-B, C-C, ... Sections

Hazardous area

Safe area (non-hazardous area)

1.4 Tool symbols

Symbol Meaning

A0011219

Phillips head screwdriver

About this document iTEMP TMT182B

4 Endress+Hauser

1.5 Documentation

Document Purpose and content of the document

Technical Information

TI01692T

Planning aid for your device

The document contains all the technical data on the device and provides

an overview of the accessories and other products that can be ordered for

the device.

Brief Operating Instructions

KA01605T

Guide that takes you quickly to the 1st measured value

The Brief Operating Instructions contain all the essential information

from incoming acceptance to initial commissioning.

Description of Device Parameters

GP01197T

The document serves as a reference for parameters: it provides a detailed

explanation for each individual parameter in the operating menu.

The document types listed are available:

In the Download Area of the Endress+Hauser Internet site: www.endress.com→

Download

1.6 Registered trademarks

HART®

Registered trademark of the FieldComm Group, Austin, Texas, USA

iTEMP TMT182B Basic safety instructions

Endress+Hauser 5

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the

application).

‣Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣Are instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣Follow the instructions in this manual.

2.2 Intended use

The device is a universal and user-configurable temperature transmitter with one sensor

input for a resistance thermometer (RTD), thermocouples (TC), resistance and voltage

transmitters. The head transmitter version of the device is intended for mounting in a

terminal head (flat face) as per DIN EN 50446. It is also possible to mount the device on a

DIN rail using the optional DIN rail clip.

If the device is used in a manner not specified by the manufacturer, the protection

provided by the device may be impaired.

The manufacturer is not liable for damage caused by improper or non-intended use.

2.3 Operational safety

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for the interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the

hazardous area (e.g. explosion protection or safety equipment):

‣Based on the technical data on the nameplate, check whether the ordered device is

permitted for the intended use in the hazardous area. The nameplate can be found on

the side of the transmitter housing.

‣Observe the specifications in the separate supplementary documentation that is an

integral part of these instructions.

Device safety and electromagnetic compatibility

The measuring system complies with the general safety requirements as per EN 61010-1,

the EMC requirements as per the IEC/EN 61326 series and the NAMUR recommendations

NE 21.

NOTICE

‣The device must only be powered by a power unit that operates using an energy-limited

electric circuit according to UL/EN/IEC 61010-1, Section 9.4 and the requirements in

Table 18.

Basic safety instructions iTEMP TMT182B

6 Endress+Hauser

2.4 Product safety

This product is designed in accordance with good engineering practice to meet state-of-

the-art safety requirements and has been tested and left the factory in a condition in

which it is safe to operate.

2.5 IT security

Our warranty is valid only if the product is installed and used as described in the Operating

Instructions. The product is equipped with security mechanisms to protect it against any

inadvertent changes to the settings.

IT security measures, which provide additional protection for the product and associated

data transfer, must be implemented by the operators themselves in line with their security

standards.

2.6 Device-specific IT security

The device offers specific functions to support protective measures by the operator. These

functions can be configured by the user and guarantee greater in-operation safety if used

correctly. The device provides a password for changing the user role (applies to operation

via FieldCare, DeviceCare, PDM).

Function/interface Factory setting Recommendation

Password Not enabled (0000) Assign a customized access code during commissioning.

Service interface (CDI) Enabled On an individual basis following risk assessment.

2.6.1 User-specific password

Write access to the device parameters via the operating tool (e.g. FieldCare, DeviceCare)

can be protected by a modifiable, user-specific password.

2.6.2 General information

• During commissioning, any passwords that were used at delivery should be changed.

• Follow the general rules for generating a secure password when defining and managing

the password.

• The user is responsible for the management and careful handling of passwords.

iTEMP TMT182B Incoming acceptance and product identification

Endress+Hauser 7

3 Incoming acceptance and product

identification

1. Unpack the temperature transmitter carefully. Is the packaging or content free from

damage?

 Damaged components must not be installed as the manufacturer can otherwise

not guarantee compliance with the original safety requirements or the material

resistance, and can therefore not be held responsible for any resulting damage.

2. Is the delivery complete or is anything missing? Check the scope of delivery against

your order.

3. Does the nameplate match the ordering information on the delivery note?

4. Are the technical documentation and all other necessary documents provided? If

applicable: are the Safety Instructions (e.g. XA) for hazardous areas provided?

If one of these conditions is not satisfied, contact your Endress+Hauser Sales Center.

3.1 Product identification

The following options are available for the identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter the serial number from the nameplate in the W@M Device Viewer

(www.endress.com/deviceviewer): All data relating to the device and an overview of the

Technical Documentation supplied with the device are displayed.

• Enter the serial number on the nameplate into the Endress+Hauser Operations App or

scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser

Operations App: all the information about the device and the technical documentation

pertaining to the device is displayed.

3.1.1 Nameplate

The right device?

Compare and check the information on the nameplate of the device against the

requirements of the measuring point.

Information on the nameplate:

• Serial number, device revision, firmware version and hardware version

• Data Matrix 2D code

• 2 lines for the TAG name and extended order code

• Approval in hazardous area with number of the relevant Ex documentation (XA...)

• Approvals with symbols

3.1.2 Name and address of manufacturer

Name of manufacturer: Endress+Hauser Wetzer GmbH + Co. KG

Address of manufacturer: Obere Wank 1, D-87484 Nesselwang or www.endress.com

Incoming acceptance and product identification iTEMP TMT182B

8 Endress+Hauser

3.2 Scope of delivery

The scope of delivery of the device comprises:

• Temperature transmitter

• Mounting material (head transmitter), optional

• Printed copy of the Brief Operating Instructions in English

• Additional documentation for devices that are suitable for use in hazardous areas, e.g.

Safety instructions (XA)

3.3 Storage and transport

Dimensions: →  46

Storage temperature

• –50 to +100 °C (–58 to +212 °F)

• Humidity: max. rel. humidity: 95 % as per IEC 60068-2-30

Pack the device for storage and transportation in such a way that it is reliably

protected against impact and external influences. The original packaging offers the

best protection.

Avoid the following environmental influences during storage:

• Direct sunlight

• Vibration

• Aggressive media

iTEMP TMT182B Mounting

Endress+Hauser 9

4 Mounting

4.1 Mounting requirements

4.1.1 Dimensions

For the device dimensions, see the 'Technical data' →  46.

4.1.2 Mounting location

In the terminal head, flat face, as per DIN EN 50446, direct mounting on insert with cable

entry (middle hole 7 mm).

Make sure there is enough space in the terminal head!

It is also possible to mount the head transmitter on a DIN rail as per IEC 60715 using

the DIN rail clip →  33 accessory.

For information about the conditions (such as the ambient temperature, degree of

protection, climate class etc.) that must be present at the installation point so that the

device can be mounted correctly, see the 'Technical data' section →  46.

When using in hazardous areas, the limit values of the certificates and approvals must be

observed (see Ex Safety Instructions).

4.2 Mounting the device

A Phillips head screwdriver is required to mount the head transmitter:

• Maximum torque for securing screws = 1 Nm (¾ foot-pound), screwdriver: Pozidriv Z2

• Maximum torque for screw terminals = 0.35 Nm (¼ foot-pound), screwdriver: Pozidriv

12 3 4 5

A0046845

 1 Head transmitter mounting

A Mounting in a terminal head (terminal head flat face as per DIN 43729)

1 Terminal head

2 Snap rings

3 Insert

Mounting iTEMP TMT182B

10 Endress+Hauser

A Mounting in a terminal head (terminal head flat face as per DIN 43729)

4 Connection wires

5 Head transmitter

6 Mounting springs

7 Mounting screws

8 Terminal head cover

9 Cable entry

Procedure for mounting in a terminal head, item A:

1. Open the terminal head cover (8) on the terminal head.

2. Guide the connection wires (4) of the insert (3) through the center hole in the head

transmitter (5).

3. Fit the mounting springs (6) on the mounting screws (7).

4. Guide the mounting screws (7) through the side boreholes of the head transmitter

and the insert (3). Fix both mounting screws with the snap rings (2).

5. Tighten the head transmitter (5) along with the insert (3) in the terminal head.

6. After wiring , close the terminal head cover (8) tightly again.

B Mounting on DIN rail (DIN rail as per IEC 60715)

1 Mounting screws

2 Head transmitter

3 Snap rings

4 DIN rail clip

5 DIN rail

Procedure for mounting on a DIN rail, item B:

1. Press the DIN rail clip (4) onto the DIN rail (5) until it engages with a click.

2. Guide the mounting screws (1) through the side boreholes of the head transmitter

(2). Then fix both mounting screws with the snap rings (3).

3. Screw the head transmitter (2) onto the DIN rail clip (4).

4.2.1 Mounting typical of North America

12 3 456

A0008520

 2 Head transmitter mounting

1 Thermowell

2 Insert

3 Adapter, coupling

4 Terminal head

5 Head transmitter

6 Mounting screws

Autres manuels Endress+Hauser Émetteur

Endress+Hauser

Endress+Hauser iTEMP TMT125 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiline M OM42 Manuel

Endress+Hauser

Endress+Hauser RMA42 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquisys M CLM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CPM253 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT112 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT182 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP HART DIN rail TMT112 Mode d'emploi

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CCM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline 300 Caractéristiques techniques

Endress+Hauser

Endress+Hauser HART Proline 400 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT85 Manuel utilisateur

Endress+Hauser

Endress+Hauser PROFIBUS DP Proline 100 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Mycom CLM 152 Manuel utilisateur

Endress+Hauser

Endress+Hauser HART Flowmeter Proline 400 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar M PMP51 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CUM 223 Manuel utilisateur

Endress+Hauser

Endress+Hauser TMT122 Manuel utilisateur

Endress+Hauser

Endress+Hauser tmt142 Caractéristiques techniques

Endress+Hauser

Endress+Hauser FHX50 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M COM 223 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur