Emerson Rosemount 3051 Manuel utilisateur

Quick Start Guide

00825-0100-4100, Rev DB

February 2019

Rosemount™ 3051 Pressure Transmitter

and Rosemount 3051CF DP Flow Meters

with WirelessHART® Protocol

Safety Messages

NOTICE

This guide provides basic guidelines for Rosemount 3051 Wireless Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting or Intrinsically Safe

(I.S.) installations. Refer to the Rosemount 3051 Wireless Reference Manual for more instruction. This

manual is also available electronically on Emerson.com/Rosemount.

Shipping considerations for wireless products:

The unit was shipped to you without the power module installed. Remove the power module prior to

shipping the unit.

Each power module contains one “D” size primary lithium-thionyl chloride battery. Primary lithium

batteries are regulated in transportation by the U.S. Department of Transportation, and are also

covered by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the responsibility

of the shipper to ensure compliance with these or any other local requirements. Consult current

regulations and requirements before shipping.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of the

Rosemount 3051 Reference Manual for any restrictions associated with a safe installation.Before

connecting a handheld communicator in an explosive atmosphere, make sure the instruments in the

loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Contents

Wireless considerations................................. 3

Transmitter installation..................................4

Troubleshooting.......................................... 16

Product certifications...................................17

Quick Start Guide February 2019

2 Emerson.com/Rosemount

1 Wireless considerations

1.1 Power up sequence

The power module should not be installed on any wireless device until the

Emerson™ Wireless Gateway (Gateway) is installed and functioning properly.

This transmitter uses the green power module (order model number

701PGNKF). Wireless devices should also be powered up in order of proximity

from the Gateway, beginning with the closest. This will result in a simpler and

faster network installation. Enable Active Advertising on the Gateway to

ensure that new devices join the network faster. For more information, see

the Emerson Wireless Gateway Reference Manual.

1.2 Connecting the transmitter with a Field Communicator

In order for the Field Communicator to interface with the Rosemount 3051

Wireless transmitter, the power module must be connected. This transmitter

uses the green power module (order model number 701PGNKF). Figure 1-1

shows how to connect the Field Communicator to the transmitter. Open the

power module compartment to hook up the leads.

Figure 1-1: Field Communicator Connections

February 2019 Quick Start Guide

Quick Start Guide 3

2 Transmitter installation

2.1 Mount the transmitter

Figure 2-1: Panel Mount Coplanar Flange

5/16 x 1½ panel bolts are customer supplied.

Figure 2-2: Pipe Mount Coplanar Flange

Quick Start Guide February 2019

4 Emerson.com/Rosemount

Figure 2-3: Panel Mount Traditional Flange

Figure 2-4: Pipe Mount Traditional Flange

Figure 2-5: Panel Mount Rosemount™ 3051T

February 2019 Quick Start Guide

Quick Start Guide 5

Figure 2-6: Pipe Mount Rosemount 3051T

2.1.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 2-7: Mounting the Transmitter in Liquid Applications

Coplanar In-line

Flow

2.1.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 2-8: Mounting the Transmitter in Gas Applications

Coplanar Inline

Quick Start Guide February 2019

6 Emerson.com/Rosemount

Flow

2.1.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 2-9: Mounting the Transmitter in Steam Applications

Coplanar In-line

Flow

2.1.4 Bolting considerations

If the transmitter installation requires assembly of the process flanges,

manifolds, or flange adapters, follow these assembly guidelines to ensure a

tight seal for optimal performance characteristics of the transmitters. Use

only bolts supplied with the transmitter or sold by Emerson as spare parts.

Figure 2-10 illustrates common transmitter assemblies with the bolt length

required for proper transmitter assembly.

February 2019 Quick Start Guide

Quick Start Guide 7

Figure 2-10: Common Transmitter Assemblies

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 ×1.75-in.

(44 mm) 4 ×1.75-in.

(44 mm)

4 × 1.75-in. (44 mm)

4 × 2.25-in. (57 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange

adapters

Bolts are typically carbon steel (CS) or stainless steel (SST). Confirm the

material by viewing the markings on the head of the bolt and referencing

Table 2-1. If bolt material is not shown in Table 2-1, contact a local Emerson

representative for more information.

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 2-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 2-1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

Quick Start Guide February 2019

8 Emerson.com/Rosemount

Example

Table 2-1: Torque Values for the Coplanar Flange and Flange Adapter

Bolts

Bolt material Head markings Initial

torque

Final

torque

B7M

300 in-lb 650 in-lb

SST

316

STM

316

B8M

150 in-lb 300 in-lb

2.1.5 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located in the neck of the transmitter, behind the housing. The

vent path is between the housing and sensor of the transmitter (see Figure

2-11).

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that the process can

drain away.

Figure 2-11: In-line Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

February 2019 Quick Start Guide

Quick Start Guide 9

2.1.6 Installing high pressure coned and threaded connection

The transmitter comes with an autoclave connection designed for high

pressure applications. Follow the steps below to properly connect the

transmitter to your process:

Procedure

1. Apply a process-compatible lubricant to the gland nut threads.

2. Slip the gland nut onto the tube, then thread the collar onto the tube

end (the collar is reverse threaded).

3. Apply a small amount of process-compatible lubricant applied to the

tube cone to help prevent galling and facilitate sealing. Insert the

tubing into the connection and tighten finger tight.

4. Tighten the gland nut to a torque of 25 ft-lb.

Note

A weep hole has been designed into the transmitter for safety and leak

detection. If fluid begins to leak from the weep hole, isolate the

process pressure, disconnect the transmitter, and reseal until the leak

is resolved.

2.2 Consider housing rotation

To improve visibility of optional LCD display:

Procedure

1. Loosen the housing rotation screw.

2. First rotate the housing clockwise to the desired location. If the desired

location cannot be achieved due to thread limit, rotate the housing

counter clockwise to the desired location (up to 360° from thread

limit).

3. Re-tighten the housing rotation screw (see Figure 2-12).

Quick Start Guide February 2019

10 Emerson.com/Rosemount

Autres manuels pour Rosemount 3051

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 4088B MultiVariable Manuel utilisateur

Emerson

Emerson Micro Motion 2400S Manuel utilisateur

Emerson

Emerson Rosemount 550PT Manuel utilisateur

Emerson

Emerson Rosemount 3300 Series Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount TCL Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 2051L Manuel utilisateur

Emerson

Emerson Rosemount 248 Manuel utilisateur

Emerson

Emerson Liebert SL-31080 Manuel utilisateur

Emerson

Emerson Rosemount 3051P Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Rosemount 708 Manuel utilisateur

Emerson

Emerson Rosemount 5400 Series Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 4600 Manuel utilisateur

Emerson

Emerson Micro Motion 800 Manuel utilisateur

Emerson

Emerson Rosemount 3095 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson 6081-P Manuel utilisateur

Emerson

Emerson Rosemount 5600 Series Manuel utilisateur

Emerson

Emerson Rosemount FCL-01 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur