Emerson Rosemount 1066 Manuel utilisateur
Quick Start Guide
00825-0100-3166, Rev AA
April 2019
Rosemount™ 1066
Single Channel Transmitter
Safety Information
Emerson designs, manufactures, and tests its products to meet many national and international
standards. Because these instruments are sophisticated technical products, you must properly install,
use, and maintain them to ensure they continue to operate within their normal specifications. The
following instructions must be adhered to and integrated into your safety program when installing,
using, and maintaining Emerson products. Failure to follow the proper instructions may cause any one
of the following situations to occur: loss of life, personal injury, property damage, damage to this
instrument, and warranty invalidation.
•Read all instructions prior to installing, operating, and servicing the product.
•If this Quick Start Guide is not the correct one, call 1 800 999 9307 to request the correct Quick
Start Guide. Save this Quick Start Guide for future reference.
•If you do not understand any of the instructions, contact your Emerson representative for
clarification.
•Follow all warnings, cautions, and instructions marked on and supplied with the product.
•Inform and educate your personnel in the proper installation, operation, and maintenance of the
product.
•Install equipment as specified in the installation instructions of the appropriate Reference Manual
and per applicable local and national codes. Connect all products to the proper electrical and
pressure sources.
•When replacement parts are required, ensure that qualified people use replacement parts
specified by Emerson. Unauthorized parts and procedures can affect the product's performance,
place the safe operation of your process at risk, and VOID YOUR WARRANTY. Look-alike
substitutions may result in fire, electrical hazards, or improper operation.
•Ensure that all equipment doors are closed and protective covers are in place, except when
maintenance is being performed by qualified people, to prevent electrical shock and personal
injury.
WARNING
Risk of electrical shock
Do not open while the circuit is live.
Only clean with a damp cloth.
NOTICE
If a 475 Universal HART® Communicator is used with these transmitters, the software within the 475
may require modification. If a software modification is required, please contact your local Emerson
Service Group or National Response Center at 1-800-654-7768.
Quick Start Guide April 2019
2 Emerson.com/Rosemount
WARNING
Electrostatic ignition hazard
Special conditions for safe use (when installed in hazardous areas)
The plastic enclosure, except the front panel, must only be cleaned with a damp cloth. The surface
resistivity of the non-metallic enclosure materials is greater than one gigaohm. Take care to avoid
electrostatic charge build-up. Do not rub or clean the transmitter with solvents or a dry cloth.
The panel mount gasket has not been tested for type of protection IP66 or Class II and III. Type of
protection IP66 and Class II, III refer to the enclosure only.
Special condition of use of Rosemount™ 1066 C FF/FII5 and 1066 T FF/FII5. For use with simple
apparatus Rosemount 140, 141, 142, 150, 400, 401, 402, 402VP, 403, 403VP, 404, and 410VP
contacting conductivity sensors and Rosemount 222, 225, 226, and 228 toroidal sensors.
Contents
Install.............................................................5
Wire.............................................................12
Navigating the display..................................23
Start up transmitter..................................... 27
Declaration of Conformity............................29
China RoHS table......................................... 31
April 2019 Quick Start Guide
Quick Start Guide 3
Quick Start Guide April 2019
4 Emerson.com/Rosemount
1 Install
1.1 Unpack and inspect
Procedure
1. Inspect the shipping container. If it is damaged, contact the shipper
immediately for instructions.
2. If there is no apparent damage, unpack the container. Be sure all
items shown on the packing list are present. If items are missing,
notify Emerson immediately.
1.2 Mount
Figure 1-1: Panel Mount Front View
April 2019 Quick Start Guide
Quick Start Guide 5
Figure 1-2: Panel Mount Side View
A. 4X mounting brackets and screws provided with instrument
B. Panel supplied by others. Maximum thickness: 0.375 in. (9.52 mm)
C. Panel mount gasket
Figure 1-3: Panel Mount Bottom View
A. Conduit openings
Quick Start Guide April 2019
6 Emerson.com/Rosemount
Figure 1-4: Panel Cut-Out
A. Maximum
Figure 1-5: Wall Mount Front View
A. 2-in. (50.8 mm) pipe supplied by customer
B. 4 cover screws
April 2019 Quick Start Guide
Quick Start Guide 7
Figure 1-6: Wall Mount Side View
Figure 1-7: Pipe Mount Bottom View
A. Front panel
B. 2-in. (50.8 mm) pipe mount bracket
C. 2 sets of U-bolts for 2-in. (50.8 mm) pipe in kit PN 23820-00
Quick Start Guide April 2019
8 Emerson.com/Rosemount
Figure 1-8: Pipe Mount Side View
1.3 General installation information
1. Install the transmitter with a sunshield or out of direct sunlight and
areas with extreme temperatures.
2. Install the system in an area where vibrations and electromagnetic
and radio frequency interference are minimized or absent.
3. Keep the transmittter and sensor wiring at least one foot from high
voltage conductors. Be sure there is easy access to the transmitter
and sample conditioning system.
4. The transmitter is suitable for panel, pipe, or surface mounting.
5. The transmitter case has six ½-in. (12.7 mm) conduit openings. Use
separate conduit openings for the power/output cable, the sensor
cable, and the other sensor cable as needed (pH input for free
chlorine with continuous pH correction).
6. Use weathertight cable glands to keep moisture out of the
transmitter. If using a conduit, plug and seal the connections at the
transmitter housing to prevent moisture from getting inside the
instrument.
7. Install cable gland fittings and plugs as needed to properly seal the
transmitter on all six enclosure openings. The USB port cover must be
fully installed on the front cover to ensure proper transmitter sealing.
April 2019 Quick Start Guide
Quick Start Guide 9
1.4 Prepare conduit openings
There are six conduit openings in all configurations of the transmitter.
Note
Emerson fits four of openings with plugs upon shipment.
Figure 1-9: Conduit openings
A. Front panel/keypad
B. Power leads
C. Alarm relay leads
D. Sensor 1 cable
E. 4-20 mA/HART®/Profibus® leads
F. Sensor 2 cable
G. Spare opening
Note
Always use proper cable gland fittings and plugs for wire and cable
installations.
Conduit openings accept ½-in. (12.7 mm) conduit fittings or PG13.5 cable
glands. To keep the case watertight, block unused openings with Type 4X or
IP66 conduit plugs.
Quick Start Guide April 2019
10 Emerson.com/Rosemount
Autres manuels pour Rosemount 1066
2
Table des matières
Autres manuels Emerson Émetteur
Emerson
Emerson Rosemount 5408 Manuel utilisateur
Emerson
Emerson CSI 9420 Manuel utilisateur
Emerson
Emerson Rosemount 3101 Manuel utilisateur
Emerson
Emerson Micro Motion 4200 Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 1199 Manuel utilisateur
Emerson
Emerson Rosemount 3051S Series Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 4600 Manuel utilisateur
Emerson
Emerson Rosemount 2051CF series Manuel utilisateur
Emerson
Emerson Rosemount 1208C Manuel utilisateur
Emerson
Emerson Rosemount FCL-01 Manuel utilisateur
Emerson
Emerson Rosemount 2051CF series Manuel utilisateur
Emerson
Emerson Rosemount 3101 Manuel utilisateur
Emerson
Emerson Micro Motion 5700 Guide rapide
Emerson
Emerson Bristol 2808 Series Manuel utilisateur
Emerson
Emerson Rosemount Analytical Oxymitter 4000 Manuel utilisateur
Emerson
Emerson Fisher C1 Manuel utilisateur
Emerson
Emerson Rosemount 3144P Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
