Emerson Rosemount 5400 Series Manuel utilisateur

Quick Start Guide

00825-0600-4026, Rev AA

March 2016

Rosemount™5400 Level Transmitter

Mounting Instructions for Parabolic Antenna

March 2016

Quick Start Guide

1.0 About this guide

This Quick Start Guide provides mechanical installation instructions for the

Rosemount 5402 Level Transmitter with parabolic antenna.

For information about electrical installation and configuration, refer to the

Rosemount 5400 Series Quick Start Guide (document number

00825-0100-4026).

Failure to follow safe installation and service guidelines could result in death or serious injury.

Make sure the transmitter is installed by qualified personnel and in accordance with applicable code of

practice.

Use the equipment only as specified in this Quick Start Guide and the Reference Manual. Failure to do so

may impair the protection provided by the equipment.

Any substitution of non-authorized parts or repair, other than exchanging the complete transmitter head

or antenna assembly, may jeopardize safety and is prohibited.

Explosions could result in death or serious injury.

Verify that the operating environment of the transmitter is consistent with the appropriate hazardous

locations specifications.

To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing.

Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in the

loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

To avoid process leaks, only use O-rings designed to seal with the corresponding flange adapter.

Do not remove the transmitter while in operation.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause electrical

shock.

Make sure the main power to the Rosemount 5400 Level Transmitter is off and the lines to any other

external power source are disconnected or not powered while wiring the transmitter.

Ground device on non-metallic tanks (e.g. fiberglass tanks) to prevent electrostatic charge build-up.

Contents

Parabolic antenna overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Mount the flanged version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Mount the welded version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6

Mount the threaded version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13

Adjust inclination of antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19

Quick Start Guide

March 2016

2.0 Parabolic antenna overview

Flanged version

Welded version

Threaded version

page 4-5

page 6-12

page 13-18

March 2016

Quick Start Guide

3.0 Mount the flanged version

Step 1: Mount antenna assembly on tank

Step 2: Adjust inclination of antenna

Refer to section “Adjust inclination of antenna” on page 19 for further

information.

Gasket

Quick Start Guide

March 2016

Step 3: Tighten blind plug or install air purging system

Proceed with electrical installation. For further instructions, see the Rosemount

5400 Series Quick Start Guide (document number 00825-0100-4026).

G3/8"

Air purging?No Yes

0.3-0.4 in. (8-10 mm)

(gasket excluded)

Torque 180 in-lb (20 Nm) Use thread sealant or

gasket according to

your site procedures.

March 2016

Quick Start Guide

4.0 Mount the welded version

Figure 1. Components

Weld protection plate

Weld protection bar

Flange ball

O-ring

Clamp flange

Washer

M8 screw

Antenna

Ball joint

Threaded sleeve

M20 adapter

G3/8" bonded seal

Blind plug

2x 1x 1x

1x 1x 1x

3x 3x

Quick Start Guide

March 2016

Step 1: Mount protection plates to flange/manhole cover

These plates protects the internal surfaces of the flange ball from welding sparks.

Ø 3.94 ± 0.02 in.

(Ø 100 ± 0.5 mm)

Max. 1.18 in. (30 mm)

March 2016

Quick Start Guide

Step 2: Weld flange ball

Step 3: Remove protection plates

Visually inspect the internal surfaces of the flange ball for damage and dirt.

Step 4: Mount O-ring

Quick Start Guide

March 2016

Step 5: Mount ball joint

Gradually tighten the M8 nuts.

Step 6: Remove protection cap

Visually inspect the O-rings for damage and dirt.

Torque 90 in-lb (10 Nm)

O-rings

March 2016

Quick Start Guide

Step 7: Carefully insert antenna

Step 8: Secure antenna

Torque 180 in-lb (20 Nm)

Autres manuels pour Rosemount 5400 Series

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Micro Motion 1700 Manuel utilisateur

Emerson

Emerson Rosemount 1199 Manuel utilisateur

Emerson

Emerson Rosemount 8782 Manuel utilisateur

Emerson

Emerson Rosemount 705 Manuel utilisateur

Emerson

Emerson Rosemount Manuel utilisateur

Emerson

Emerson Rosemount 1408H Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Rosemount 248 Manuel utilisateur

Emerson

Emerson Rosemount X-STREAM O2 Transmitter Manuel utilisateur

Emerson

Emerson Micro Motion ELITE Manuel utilisateur

Emerson

Emerson Micro Motion 3700 Manuel utilisateur

Emerson

Emerson Rosemount 3308 Manuel utilisateur

Emerson

Emerson Rosemount 3051N Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Rosemount CX1100 Manuel utilisateur

Emerson

Emerson Rosemount 5300 Series Manuel d'exploitation

Emerson

Emerson Rosemount 848T Manuel utilisateur

Emerson

Emerson ROSEMOUNT 5300 Guide de configuration

Emerson

Emerson Rosemount HART Modbus VeriCase 3308 Series Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Rosemount 1056 Manuel utilisateur

Emerson

Emerson Rosemount 3051SF Series Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur