Emerson Rosemount 1056 Manuel utilisateur

Quick Start Guide

00825-0100-3156, Rev AA

April 2019

Rosemount™ 1056

Four-Wire, Dual-Input Intelligent

Transmitter

Safety information

Your instrument purchase from Emerson is one of the finest available for your particular application.

These instruments have been designed and tested to meet many national and international standards.

Experience indicates that its performance is directly related to the quailty of the installation and

knowledge of the user in operating and maintaining the instrument. To ensure its continued operation

to the design specifications, personnel should read this Quick Start Guide thoroughly before

proceeding with installation, commissioning, operation, and maintenance of this instrument. If this

equipment is used in a manner not specified by the manufacturer, the protection provided by it against

hazards may be impaired.

•Failure to follow the proper instructions may cause any one of the following situations to occur:

loss of life, personal injury, property damage, damage to this instrument, and warranty

invalidation.

•Ensure that you have received the correct model and options from your purchase order. Verify

that this Quick Start Guide covers your model and options. If it does not, call 800 854 8257 or 949

757 8500 to request the correct Quick Start Guide.

•For clarification of instructions, contact your Rosemount™ representative.

•Follow all warnings, cautions, and instructions marked on and supplied with the product.

•Use only qualified personnel to install, operate, program, and maintain the product.

•Install equipment as specified in the Installation section of this Quick Start Guide. Follow

appropriate local and national codes. Only connect the product to electrical and pressure sources

specified in this Quick Start Guide.

•Use only factory documented components for repair. Tampering or unauthorized substitution of

parts and procedures can affect the performance and cause unsafe operation of your process.

•All equipment doors must be closed, and protective covers must be in place unless qualified

personnel are performing maintenance.

WARNING

Risk of electrical shock

Installation and servicing of this product may expose personnel to dangerous voltages.

Equipment protected throughout by double insulation.

Disconnect main power wired to separate power source before servicing.

Do not operate or energize instrument with case open.

Signal wiring within this box must be rated at least 240 V.

Non-metallic cable strain reliefs do not provide grounding between conduit connections. Use

grounding type bushings and jumper wires.

Unused cable conduit entries must be securely sealed by non-flammable closures to provide

exposure integrity in compliance with personal safety and environmental protection

requirements. Unused conduit openings must be sealed with NEMA 4X or IP65 conduit plugs to

maintain the ingress protection rating (IP65).

Electrical installation must be in accordance with the National Electrical Code (ANSI/NFPA-70)

and/or any other national or local codes.

Operate only with front panel fastened and in place.

Safety and performance require that this instrument be connected and properly grounded

through a three-wire power source.

Proper use and configuration is the operator's responsibility.

Quick Start Guide April 2019

2 Emerson.com/Rosemount

Contents

First steps.......................................................5

Install.............................................................9

Wire.............................................................10

Navigating the display..................................23

Startup.........................................................29

EU Declaration of Conformity.......................32

China RoHS Table.........................................34

April 2019 Quick Start Guide

Quick Start Guide 3

Quick Start Guide April 2019

4 Emerson.com/Rosemount

1 First steps

1.1 Unpack and inspect

Procedure

1. Inspect the shipping container. If it is damaged, contact the shipper

immediately for instructions.

2. If there is no apparent damage, unpack the container. Be sure all

items shown on the packing list are present. If items are missing,

notify Emerson immediately.

1.2 Mount

Figure 1-1: Panel Mount Front View

April 2019 Quick Start Guide

Quick Start Guide 5

Figure 1-2: Panel Mount Side View

A. Panel mount gasket

B. 4X mounting brackets and screws provided with instrument

C. Panel supplied by others: maximum thickness .375-in. (9.52 mm)

Figure 1-3: Panel Mount Bottom View

A. 6X conduit openings

Quick Start Guide April 2019

6 Emerson.com/Rosemount

Figure 1-4: Panel Mount Panel Cut-out

A. Maximum radius

Note

Panel mounting seal integrity (4/4X) for outdoor applications is the end

user's responsibility.

Figure 1-5: Wall Mount Front View

A. 4X cover screw

April 2019 Quick Start Guide

Quick Start Guide 7

Figure 1-6: Wall Mount Side View

Figure 1-7: Pipe Mount Bottom View

A. Front panel

B. Panel and pipe mount enclosure

C. Conduit openings

D. 2-in. pipe mount bracket

Quick Start Guide April 2019

8 Emerson.com/Rosemount

2 Install

2.1 General installation information

WARNING

Electrical shock

Electrical installation must be in accordance with the National Electric Code

(ANSI/NFPA-70) and/or any other applicable national or local codes.

1. Install the transmitter with a sunshield or out of direct sunlight and

areas with extreme temperatures.

2. Install the system in an area where vibrations and electromagnetic

and radio frequency interference are minimized or absent.

3. Keep the transmittter and sensor wiring at least one foot from high

voltage conductors. Be sure there is easy access to the transmitter

and sample conditioning system.

4. The transmitter is suitable for panel, pipe, or surface mounting.

April 2019 Quick Start Guide

Quick Start Guide 9

3 Wire

3.1 General wiring information

The transmitter is easy to wire. It includes removable connectors and slide-

out signal input boards. The front panel is hinged at the bottom. The panel

swings down for easy access to the wiring locations.

3.1.1 Removable connectors and signal input boards

The transmitter uses removable signal input boards and communication

boards for ease of wiring and installation. You can remove each of the signal

boards either partially or completely from the enclosure for wiring. The

transmitter has three slots for placement of up to two signal input boards

and one communication board.

Slot 1 - left Slot 2 - center Slot 3 - right

Comm board Input board 1 Input board 2

3.1.2 Signal input boards

Slots 2 and 3 are for signal input measurement boards.

Procedure

1. Wire the sensor leads to the measurement board following the lead

locations marked on the board.

2. Carefully slide the wired board fully into the enclosure slot and take

up the excess sensor cable through the cable gland.

3. Tighten the cable gland nut to secure the cable and ensure a sealed

enclosure.

3.1.3 Digital communication boards

HART® and Profibus® DP communication boards will be available in the

future as options for Rosemount™ 1056 digital communication with a host.

The HART board supports Bell 202 digital communications over an analog

4-20 mA current output. Profibus DP is an open communications protocol

that operates over a dedicated digital line to the host.

3.1.4 Alarm relays

Emerson supplies four alarm relays with the switching power supply (85 to

264 Vac, 03 order code) and the 24 Vdc power supply (20 - 30 Vdc, 02 order

code). You can use all relays for process measurement(s) or temperature.

You can also configure any relay as a fault alarm instead of a process alarm.

Quick Start Guide April 2019

10 Emerson.com/Rosemount

Autres manuels pour Rosemount 1056

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 1152 Alphaline Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Rosemount 2051 Manuel utilisateur

Emerson

Emerson Rosemount 8712EM Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Micro Motion 1700 Guide rapide

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Rosemount 3095FB MultiVariable MODBUS Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Rosemount 3051SF Series Manuel utilisateur

Emerson

Emerson Rosemount 5600 Series Manuel d'exploitation

Emerson

Emerson Micro Motion 800 Manuel utilisateur

Emerson

Emerson Rosemount 1066 Manuel utilisateur

Emerson

Emerson Micro Motion Transmitters and Discrete Controllers Series... Manuel d'exploitation

Emerson

Emerson Rosemount 148 Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Rosemount Ultrasonic 3107 Manuel utilisateur

Emerson

Emerson Rosemount TCL Manuel utilisateur

Emerson

Emerson PT4 Manuel utilisateur

Emerson

Emerson Rosemount ET310 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur