Ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manuel utilisateur

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector RTX 3080/3090 D-RGB

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process, to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

PREPARING THE GRAPHICS CARD 6

REMOVING THE STOCK COOLER 6

CLEANING THE PCB 6

CUTTING AND PLACING THERMAL PADS 7

APPLYING THERMAL COMPOUND 8

INSTALLING THE WATER BLOCK 8

PLACING THE BLOCK ON THE GRAPHICS CARD 8

ATTACHING THE BLOCK TO THE GRAPHICS CARD 9

CHECKING FOR CONTACT 9

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 9

INSTALLATION OF FITTINGS AND TUBING 10

CONNECTING THE D-RGB LED STRIP* 10

TESTING THE LOOP 11

SUPPORT AND SERVICE 12

SOCIAL MEDIA 12

- 4 -

BOX CONTENTS

4 mm

6 mm

8 mm

M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)

M2.5 Nut (2 pcs)

M2,5x6 AX1 Screw (13 pcs)

Allen Key 2.5. mm (1 pc)

Thermal Pad F 1.0 mm (4 pcs)

Thermal Grease (1 pc)M2,5x8 AX1 Screw (2 pcs)

M2,5x4 AX1 Screw (16 pcs)EK-Quantum Vector RTX 3080/3090 D-RGB

M2.5 PVC Washers (16 pcs)

120 mm

16 mm

EK-Plug G1/4 (2 pcs)

Mounting mechanism - You may not need all the screws, mounting mechanism is universal!

- 5 -

WATER BLOCK DIMENSIONS

220.15 mm

112.51 mm

124.01 mm

91.70 mm

120.70 mm 20.55 mm

- 6 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove the

stock cooler. Do not forget to unplug all the LED and fan connectors.

Pay attention to the following steps in order to install the EK-Quantum

Vector RTX 3080/3090 D-RGB water block onto the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers.

STEP 2

- 7 -

CUTTING AND PLACING THERMAL PADS

STEP 1

Your GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Replacement thermal pads:

4x Thermal Pad F 1.0mm – (120X16mm) EAN: 3830046996732

STEP 2

Once cut to size, thermal pads should be placed on the PCB, as

illustrated below. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

STEP 2

STEP 1

RTX™ 3080/3090:

120 mm

16 mm

1 mm

Thermal Pad F – 1.0 mm

- 8 -

APPLYING THERMAL COMPOUND

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the CPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

For this Step, you will need: Thermal Grease, EAN: 3830046998446

STEP 1

Thermal Grease

1 pc

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks.

Carefully position the water block with preinstalled standoffs on

the graphics card. During this process, make sure you have aligned

mounting holes of the PCB with holes of the water block (same

applies to other tops).

Pay attention not to use too much force when pressing the

block down to the PCB since chip dies are prone to cracking.

STEP 1

- 9 -

STEP 2

M2.5 x 4 AX1 Screw

M2.5 PVC Washer

STEP 2

ATTACHING THE BLOCK TO THE GRAPHICS CARD

Use twelve (12) M2.5 X 4 AX1 screws and M2.5 PVC washers.

Tighten the screws evenly using the Phillips head screwdriver. EK

recommends you start tightening the screws around the GPU core

ﬁrst, and then continuing outward to prevent the damage to the

GPU. Always use a plastic washer under each screw!

For this Step, you will need:

M 2.5 PVC Washer

12 pcs

M2.5 x 4 AX1

12 pcs

Phillips Head

Screwdriver

CHECKING FOR CONTACT

If necessary, temporarily remove the water block to check for uniform

surface contact between the block and components. Pay special

attention to the VRM section of the graphics card. Check whether

the water block makes contact with the intended integrated circuit.

Then repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check again

or contact our support service at www.ekwb.com/support.

INSERTING THE GRAPHICS CARD INTO THE CHASSIS

Carefully lift your graphics card with the installed water block and

insert it into your PC’s motherboard PCIexpress expansion slot.

Please bear in mind that your graphics card is very likely heavier than

before it was equipped with the water block.

You need to be very careful when handling the graphics

card. Avoid all unnecessary manipulation of the water block

assembly that might damage your card or water block.

- 10 -

INSTALLATION OF FITTINGS AND TUBING

CONNECTING THE D-RGB LED STRIP*

STEP 1

Screw-in two (2) G1/4 threaded male ﬁttings. Attach the liquid

cooling tubes and connect the water block(s) to the cooling loop.

Do not forget to plug the remaining two openings with

enclosed EK-Plug G1/4 or its equivalent.

You can use any opening as an inlet/outlet port.

EK recommends using EK ﬁttings with all EK water blocks.

CAUTION: When using connectors other than EK ﬁttings,

pay special attention to the length of the ﬁttings’ male G1/4”

thread - 5mm is the maximum G1/4” thread length allowed!

STEP 1

Plug the 4-pin D-RGB connector from the GPU water block to the

D-RGB Header on your motherboard or controller. The LED strip will

work only if the pin layout on the header is as follows: +5V, Data,

Empty, Ground.

Incorrect installation or installation to a wrong header can

damage to the LED strip or the header itself!

*optional step

STEP 1

Tubing

EK- Plug

G1/4

EK-Fitting

D-RGB Header

RGB Header

Autres manuels pour EK-Quantum Vector RTX 3080/3090 D-RGB

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb CPU Lignum Manuel utilisateur

ekwb

ekwb EK-FCQ6000 Manuel

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

ekwb

ekwb EK-XRES 100 Revo D5 Series Manuel

ekwb

ekwb EK-FC970 GTX TF5 Manuel

ekwb

ekwb EK-FC Fury X Manuel

ekwb

ekwb EK-FC480 GTX Manuel

ekwb

ekwb EK-Pro CPU Water Block SP5 Manuel utilisateur

ekwb

ekwb EK-FC R9-290X Lightning Series Manuel

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manuel utilisateur

ekwb

ekwb EK-FC680 GTX FTW Mode d’emploi

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manuel utilisateur

ekwb

ekwb EK-RES X3 D-RGB Manuel utilisateur

ekwb

ekwb EK-PRO GPU WB RTX 30x0 Manuel utilisateur

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Manuel utilisateur

ekwb

ekwb Velocity - Intel Manuel utilisateur

ekwb

ekwb EK-XRES 140 Revo D5 Series Mode d’emploi

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manuel utilisateur

ekwb

ekwb EK-FC Titan V Manuel utilisateur

ekwb

ekwb EK-Quantum Vector TUF RX 6800 Manuel utilisateur

ekwb

ekwb EK Series Manuel utilisateur

ekwb

ekwb EK-FC R9-295X2 Manuel

ekwb

ekwb EK-FB GA Z87X-OC Force Mode d’emploi

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Backplate Mode d’emploi

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques