Ekwb EK-PRO GPU WB RTX 30x0 Manuel utilisateur

USER GUIDE

GPU WATER BLOCK

EK-PRO

GPU WB RTX 30x0

All manuals and user guides at all-guides.com

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

All manuals and user guides at all-guides.com

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 8

INSTALLING THE WATER BLOCK 9

PLACING THE BLOCK ON THE GRAPHICS CARD 9

ATTACHING THE BACKPLATE 11

CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

All manuals and user guides at all-guides.com

- 4 -

EK-PLUG G1/4 (2x)

3830046999153

BOX CONTENTS

Screw M2.5x4 ax1 (16x)

9047

EK-Loop Multi Allen Key (1x)

3830046996213

EK-Loop Multi Allen Key (1x)

3830046996213

Thermal PAD F 1.0mm - (120x16mm)

(7x) 3830046996732

Screw M3x4 DIN7985 (2x)

8123

EK-TIM Ectotherm (1g) (1x)

830046998446

Nut M2.5 (6x)

8506

Screw M2.5x10 ax1

(13x) 104344

Washer

POLYAMID M2.5 0.5mm

(16x) 8623

Screw M2.5x8 ax1 (9x)

8104A

EK-Pro GPU WB RTX 3080/3090 Ni +Inox

(1x) 3831109848616

Washer POLYAMID M2.5 0.7mm

with self-adhesive tape (2x) 8627

Allen Key 2.5mm (1x)

8902

120 mm

16 mm

Screw M2.5x6 ax1 (13x)

9058

All manuals and user guides at all-guides.com

- 5 -

WATER BLOCK DIMENSIONS

99.6 mm

126.6 mm

125.6 mm

152.6 mm

219.3 mm

230.3 mm

18.8 mm

21.8 mm

All manuals and user guides at all-guides.com

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

Position EAN Description Quantity

1103757 Copper – Pro GPU WB RTX 3080-

3090 Coldplate (Ni) 1

2100845 Standoff M4/M2.5x2.5 - HEX 9

38627 Washer POlYAMID M2.5 0.7mm 3

4100006 Screw M4x27 DIN7984 1

5103090 Screw M3x6 ISO 14581 TX – inox 14

6102931 OR Vector RE 30x0 1

7101975 029 – top plexi – FC-Quadro RTX

8000 Pro - insert 1

8102490 Brass – Pro GPU bracket standoff

M4-6/32 - Ni 1

9103758 Metal – Pro GPU WB RTX 3080-

3090 Top inox 1

10 102549 Metal – Pro GPU WB Jet 1

11 103812 Alu – Pro GPU WB RTX 30x0

backplate 1

12 100663 EK RGB Badge 2

13 8483 ISO 7380 – UNC 6-32x5 1

14 5155 OR 15x1 EPDM50 (FC Terminal) 2

15 3674 Top Acetal – FC Terminal M4

Pre-ﬁlled 1

16 9013 Screw M4x8 DIN7984 2

All manuals and user guides at all-guides.com

- 7 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove

the stock cooler. Do not forget to unplug all the LED and fan

connectors. Pay attention to the following steps in order to install

the EK-Pro GPU WB RTX 30x0 water block onto the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

STEP 2

All manuals and user guides at all-guides.com

- 8 -

CUTTING AND PLACING THERMAL PADS

Your GPU water block comes with un-cuted thermal pads to cover all

the VRM components, such as COILs, MOSFETs, and drivers. Please

use 1.0mm thick thermal pads which should be placed on the PCB,

as illustrated below. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal Pad F 1.0 mm

Thermal Grease

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the GPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 1

APPLYING THERMAL COMPOUND

For this Step, you will need:

All manuals and user guides at all-guides.com

- 9 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks. Carefully

position the water block with preinstalled standoffs on the graphics

card. During this process, make sure you have aligned mounting

holes of the PCB with holes of the water block.

Pay attention not to use too much force when pressing

the block down to the PCB since chip dies are prone

to cracking.

STEP 1

STEP 2

Make sure that three (3) the self-adhesive M2,5 plastic washers are

in place as shown in picture.

Pay attention to the front area, where I/O ports are, those

metal springs may get in the way when inserting, holes on

PCB and block needs to be perfectly aligned!

All manuals and user guides at all-guides.com

- 10 -

STEP 2

M2.5 x 4 AX1

SCREW

M2.5 PVC WASHER

STEP 2

To mount the graphics card onto the waterblock, stock cross

backplate needs to be use. Attach it with ﬁve (5) M2.5 Washers and

M2.5 X 4 AX1 screws.

STEP 3

Install 1.0mm thick thermal pads on the PCB, as illustrated below

to ensure better connection between graphic card and backplate.

EK made sure to provide you with more than an adequate quantity

of thermal pads to complete this Step.

Thermal Pad F 1.0 mm

All manuals and user guides at all-guides.com

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FC 780 GTX DCII Original CSQ Manuel

ekwb

ekwb EK-Pro CPU Water Block SP5 Manuel utilisateur

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manuel utilisateur

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Manuel utilisateur

ekwb

ekwb EK-FC670 GTX DCII Mode d’emploi

ekwb

ekwb EK-Thermosphere Manuel

ekwb

ekwb EK-FC590 GTX Mode d’emploi

ekwb

ekwb EK-FC R9-290X Original CSQ Manuel utilisateur

ekwb

ekwb EK-FB ASUS R4BE Monoblock Manuel utilisateur

ekwb

ekwb EK-FC1080 GTX Ti Aorus Manuel utilisateur

ekwb

ekwb EK-FCW8100 Mode d’emploi

ekwb

ekwb EK-FC R9-295X2 Manuel

ekwb

ekwb EK-FC R9 290X DCII Mode d’emploi

ekwb

ekwb EK-FC1080 G1 GTX Backplate Mode d’emploi

ekwb

ekwb EK-Quantum Vector FE RTX 3090... Manuel utilisateur

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Manuel utilisateur

ekwb

ekwb EK-FC 780 GTX Jetstream Manuel utilisateur

ekwb

ekwb EK-FC 6970 V2 Manuel

ekwb

ekwb EK-XTOP D5 Mode d’emploi

ekwb

ekwb EK-Annihilator Series Manuel utilisateur

ekwb

ekwb EK-FC980 GTX TF5 Manuel

ekwb

ekwb EK-Classic 115x/20xx D-RGB Manuel utilisateur

ekwb

ekwb EK-Vardar X3M 120ER Manuel utilisateur

ekwb

ekwb EK-FC 6970 V2 Manuel

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-PRO GPU WB RTX 30x0 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques