ekwb EK-PRO GPU WB RTX 30 0 Series Manuel utilisateur
USER GUIDE
GPU WATER BLOCK
EK-PRO
GPU WB RTX 30x0
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 8
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE BACKPLATE 11
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12
TESTING THE LOOP 12
SUPPORT AND SERVICE 13
SOCIAL MEDIA 13
- 4 -
EK-PLUG G1/4 (2x)
3830046999153
BOX CONTENTS
Screw M2.5x4 ax1 (16x)
9047
EK-Loop Multi Allen Key (1x)
3830046996213
EK-Loop Multi Allen Key (1x)
3830046996213
Thermal PAD F 1.0mm - (120x16mm)
(7x) 3830046996732
Screw M3x4 DIN7985 (2x)
8123
EK-TIM Ectotherm (1g) (1x)
830046998446
Nut M2.5 (6x)
8506
Screw M2.5x10 ax1
(13x) 104344
Washer
POLYAMID M2.5 0.5mm
(16x) 8623
Screw M2.5x8 ax1 (9x)
8104A
EK-Pro GPU WB RTX 3080/3090 Ni +Inox
(1x) 3831109848616
Washer POLYAMID M2.5 0.7mm
with self-adhesive tape (2x) 8627
Allen Key 2.5mm (1x)
8902
120 mm
16 mm
Screw M2.5x6 ax1 (13x)
9058
- 5 -
WATER BLOCK DIMENSIONS
99.6 mm
126.6 mm
125.6 mm
152.6 mm
219.3 mm
230.3 mm
18.8 mm
21.8 mm
- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Position EAN Description Quantity
1103757 Copper – Pro GPU WB RTX 3080-
3090 Coldplate (Ni) 1
2100845 Standoff M4/M2.5x2.5 - HEX 9
38627 Washer POlYAMID M2.5 0.7mm 3
4100006 Screw M4x27 DIN7984 1
5103090 Screw M3x6 ISO 14581 TX – inox 14
6102931 OR Vector RE 30x0 1
7101975 029 – top plexi – FC-Quadro RTX
8000 Pro - insert 1
8102490 Brass – Pro GPU bracket standoff
M4-6/32 - Ni 1
9103758 Metal – Pro GPU WB RTX 3080-
3090 Top inox 1
10 102549 Metal – Pro GPU WB Jet 1
11 103812 Alu – Pro GPU WB RTX 30x0
backplate 1
12 100663 EK RGB Badge 2
13 8483 ISO 7380 – UNC 6-32x5 1
14 5155 OR 15x1 EPDM50 (FC Terminal) 2
15 3674 Top Acetal – FC Terminal M4
Pre-filled 1
16 9013 Screw M4x8 DIN7984 2
2
5
11
9
16
13
8
12
6
7
10
10
1
14
14
15
- 7 -
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove
the stock cooler. Do not forget to unplug all the LED and fan
connectors. Pay attention to the following steps in order to install
the EK-Pro GPU WB RTX 30x0 water block onto the graphics card.
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 2
- 8 -
CUTTING AND PLACING THERMAL PADS
Your GPU water block comes with un-cuted thermal pads to cover all
the VRM components, such as COILs, MOSFETs, and drivers. Please
use 1.0mm thick thermal pads which should be placed on the PCB,
as illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal Pad F 1.0 mm
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 1
APPLYING THERMAL COMPOUND
For this Step, you will need:
- 9 -
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks. Carefully
position the water block with preinstalled standoffs on the graphics
card. During this process, make sure you have aligned mounting
holes of the PCB with holes of the water block.
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1
STEP 2
STEP 2
Make sure that three (3) the self-adhesive M2,5 plastic washers are
in place as shown in picture.
Pay attention to the front area, where I/O ports are, those
metal springs may get in the way when inserting, holes on
PCB and block needs to be perfectly aligned!
- 10 -
STEP 2
M2.5 x 4 AX1
SCREW
M2.5 PVC WASHER
STEP 2
To mount the graphics card onto the waterblock, stock cross
backplate needs to be use. Attach it with five (5) M2.5 Washers and
M2.5 X 4 AX1 screws.
STEP 3
STEP 3
Install 1.0mm thick thermal pads on the PCB, as illustrated below
to ensure better connection between graphic card and backplate.
EK made sure to provide you with more than an adequate quantity
of thermal pads to complete this Step.
Thermal Pad F 1.0 mm
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels ekwb Matériel informatique
ekwb
ekwb EK-FB ASUS R5-E10 Mode d’emploi
ekwb
ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manuel utilisateur
ekwb
ekwb EK-FC980 GTX Classy Manuel
ekwb
ekwb EK H30 SUPREME Manuel utilisateur
ekwb
ekwb Classic D-RGB S240 Manuel utilisateur
ekwb
ekwb EK-FC1080 GTX Backplate Mode d’emploi
ekwb
ekwb EK-FCS10000 Manuel
ekwb
ekwb EK-RAM Dominator Manuel
ekwb
ekwb EK-FB ASUS X58 Mode d’emploi
ekwb
ekwb EK-FCQK6000 Mode d’emploi
ekwb
ekwb EK-FC1080 GTX JetStream Manuel utilisateur
ekwb
ekwb EK-FB GA X470 Gaming 7 RGB Manuel utilisateur
ekwb
ekwb Velocity Manuel utilisateur
ekwb
ekwb EK-Quantum Reflection PC-O11D XL D5 PWM... Manuel utilisateur
ekwb
ekwb EK-FC R9-295X2 Manuel
ekwb
ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manuel utilisateur
ekwb
ekwb EK-Classic AM4 D-RGB Manuel utilisateur
ekwb
ekwb EK-Vardar X3M 120ER Manuel utilisateur
ekwb
ekwb EK-D5 Dual TOP CSQ Manuel
ekwb
ekwb EK-FC285 GTX Classified Manuel
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
