Ekwb EK-FB ASUS P7P55 KIT Mode d’emploi

Installation and mounting manuals for EK-FB ASUS P7P55 KIT water block:

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION. Sam

icture of P7P55D motherboard.

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws or plugs. All heat

sink assembly screws should be removed. There are 6 screws on the back of the

motherboard.

2. CLEANING THE PCB. Carefully detach the original heat sink after removing all

fasteners securing it to the board and bracket. Wipe off the remains (by using non–

abrasive cloth or qtip, as shown on sample photo) of the original thermal compound

until the components and circuit board are completely clean. EKWB does not

recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Southbridge with for example Céramique™

thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should be

applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. Your block comes with two precut thermal pads,

which have to be placed on mosfet chips. (PLEASE REMOVE FOIL OF THERMAL

PADS PRIOR TO INSTALLATION.)

5. PLACING MOSFET BLOCK ON MOTHERBOARD. Place copper base facing

mosfet chips directly onto thermal pads and use 4 enclosed screws size M3x6

with PVC washer to secure position of mosfet block. Please make sure you

tighten all screws equally, without using too much force. Otherwise middle

mosfet chips may not have proper contact / cooling.

6. PLACING SOUTHBRIDGE BLOCK ON MOTHERBOARD. Place southbridge

block over chip. Afterwards insert springs and 2 screws M3x25 as shown on

picture bellow. Carefully flip your motherboard to the other side.

Placethermalpadshere.

M3×25mmscrew

Spring

M3PVCWashers

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon15thofJuly,2009.

7. ATTACHING THUMB NUTS. Place all mounting elements in same order as bellow and equally and gradually tighten thumb nuts to prevent the core from breaking .

Before moving onto next step, please make sure that spring is appropriately compressed in hole as shown on sample picture (right).

STEP 3: CHECKING FOR CONTACTS

Temporarily r

emove the water blocks to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 5 and 7 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 4: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB ASUS P7P55D KIT series are usually sold with high flow

fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always recommended

for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 2 screws M3x25 DIN965 4 screws M3x6 DIN7985

Thumbnut

Metalwasher

PVCwasher

Fittings

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-Classic GPU Water BlockRTX 2080Ti D-RGB Manuel utilisateur

ekwb

ekwb EK-Quantum Momentum TRX40 Aorus Master Manuel utilisateur

ekwb

ekwb MSI MPG Z490 Carbon EK X Manuel utilisateur

ekwb

ekwb EK-MSI Z690 Carbon EK X Manuel utilisateur

ekwb

ekwb EK-UNI RAD Manuel

ekwb

ekwb EK-7970 Mode d’emploi

ekwb

ekwb EK-FC R9-290X Manuel

ekwb

ekwb EK-Annihilator Pro ILM Series Manuel utilisateur

ekwb

ekwb EK-Quantum Reflection PC-O11D D5 PWM D-RGB Manuel utilisateur

ekwb

ekwb EK-FC 5970 Manuel

ekwb

ekwb EK-FB KIT GA-X99 LE Mode d’emploi

ekwb

ekwb EK-FC1080 GTX Ti Aorus RGB Manuel utilisateur

ekwb

ekwb EK-Quantum Magnitude Manuel utilisateur

ekwb

ekwb EK-FC Titan Series Manuel

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manuel utilisateur

ekwb

ekwb EK-FC780 GTX WF3 Manuel

ekwb

ekwb EK-Quantum Vector TUF RX 6800 Manuel utilisateur

ekwb

ekwb EK-FC670 GTX DCII Mode d’emploi

ekwb

ekwb EK-Quantum Magnitude sTRX4 Manuel utilisateur

ekwb

ekwb EK-Loop Fan FPT 120 FAN Manuel utilisateur

ekwb

ekwb EK-FC480 GTX Manuel

ekwb

ekwb EK-Classic 115x/20xx D-RGB Manuel utilisateur

ekwb

ekwb EK-Quantum Volume FLT Series Manuel utilisateur

ekwb

ekwb EK-FC980 GTX Ti Strix Manuel

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-FB ASUS P7P55 KIT Mode d’emploi

Manuels Matériel informatique populaires d'autres marques