Ekwb EK-DBAY RES SPIN Mode d’emploi

Released on 26th of February, 2014.

Installation and mounting manual for EK-DBAY RES SPIN

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EKWB d.o.o. assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

EKWB recommends 24 hour leak testing for all EK products before powering on the computer. This will eliminate any damages that may occur because of the users improper installation or

products imperfections.

STEP 1: GENERAL INFORMATION. Sample picture of EK-DBAY RES SPIN

STEP 2: PREPARING YOUR RESERVOIR

Take your reservoir and place it on a flat and clean surface. In case you bought extra impellers and you wish to swap the original one then simply unscrew all

screws attaching (with enclosed allen key) the acrylic top to the base of the reservoir and replace impeller. Before closing reservoir make sure the impeller is able

to rotate around it's axis –the easiest way to check this is to blow air gently over the impeller’s blades in order to make sure it spins flawlessly without making

any kind of unusual grinding noises. If you encounter difficulties rotating the impeller please check impeller’s axis shaft. When attaching the acrylic top back to

the reservoir's base avoid using the excessive force since acrylic is prone to cracking. Make sure the rubber gasket is positioned inside it's channel. Usually the

sign of waterproof seal is when gasket flattens against the acrylic top.

STEP 3: MOUNTING THE RESERVOIR INSIDE YOUR COMPUTER CHASSIS:

This reservoir occupies two 5.25” drive bay expansion slots in your computer chassis. Free two slots in case they are already occupied with other

computer components such as optical- or hard disk drives. Place the reservoir in your

5.25" drive bay

out with the front plate facing outwards. Secure

the reservoir to the drive bay cage using the enclosed M3x4 DIN7985 screws.

M3x4 DIN7985 screw

Released on 26th of February, 2014.

STEP 4: CONNECTING YOU RESERVOIR

You can use any G1/4 threaded ports marked as an outlet port except for the inlet port which is clearly marked (“IN”). We recommend using the 2

outlet port right beneath the J-shaped plastic extrusion which eases the air bleeding process significantly. Make sure unused outlet ports are plugged

with enclosed plugs.

STEP 5: FILL THE RESERVOIR

Fill reservoir through G3/8 threaded fill port (marked with arrow) and make sure liquid is not spilled over your computer or any electrical devices nearby.

Preferably, your pump's height level should be lower than that of the EK-DBAY RES SPIN in order to flood and prime the water pump. Run your pump shortly for

couple of times to make sure water floods your tubes and other water cooling components. Repeat the procedure until you are done and pay attention to the

water level in your reservoir. Idealy there should be only so much water to make waterfall effect still noticable in the reservoir. Lowest and highest

recommendable water levels are indicated on the reservoir's front panel (

min

max

). Once done with filling please close your EK-DBAY RES SPIN with G3/8 plug

and tighten the seal using enclosed allen key.

STEP 5: OTHER INSTRUCTIONS

Please note that EKWB holds no responsibility of any kind if assembly is not performed as per instructions. This applies also for all

products that are not listed as compatible on web page. Users must by all means also consider instructions that are being made

for proper use of pump and other water cooling components/liquids provided by manufacturer(s).

HINT: Never let your pump running dry. Prolonged dry use enhances the risk of damaging the pump’s bearing thus rendering

pump useless.

Predrilled holes for

5mm LEDs (acrylic

version only)

EK G1/4 Plug

Outlet G1/4 threaded ports

Inlet G1/4

threaded port

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FB ASUS R5-E10 Mode d’emploi

ekwb

ekwb EK Series Manuel utilisateur

ekwb

ekwb EK-Velocity sTR4 Manuel utilisateur

ekwb

ekwb EK-PRO GPU WB RTX 30x0 Manuel utilisateur

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock Manuel utilisateur

ekwb

ekwb EK-Quantum RX 6800 Manuel utilisateur

ekwb

ekwb EK-FC7970 Manuel

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manuel utilisateur

ekwb

ekwb EK-FC R9-290X Manuel

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON RGB... Manuel utilisateur

ekwb

ekwb EK-FB ASUS ROG ZE Monoblock Manuel utilisateur

ekwb

ekwb EK-Pro GPU WB RTX 8000 - Ni + Inox Manuel utilisateur

ekwb

ekwb EK-PRO GPU WB RTX A100 80GB Manuel utilisateur

ekwb

ekwb EK-D5 Dual TOP Mode d’emploi

ekwb

ekwb EK-Vector RTX 2080 Backplate Mode d’emploi

ekwb

ekwb EK-FB ASUS Z270E Strix Monoblock Series Manuel utilisateur

ekwb

ekwb EK-FC 5870 MSI Manuel

ekwb

ekwb EK-Supremacy Elite Edition series Manuel utilisateur

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Mode d’emploi

ekwb

ekwb EK-FC Radeon Vega Strix Backplate Manuel

ekwb

ekwb EK-Quantum Vector FTW3 RTX 3070 Manuel utilisateur

ekwb

ekwb EK-FC980 GTX Ti Strix Series Manuel

ekwb

ekwb EK-Quantum Kinetic FLT D5/DDC Body D-RGB Manuel utilisateur

ekwb

ekwb EK-FC RX-480 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-DBAY RES SPIN Mode d’emploi

Manuels Matériel informatique populaires d'autres marques