Ekwb EK-Quantum Velocity 2 Manuel utilisateur

USER GUIDE

EK-Quantum

Velocity² - AM5 Backplate

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced or

feel unsure about the installation procedure, please refrain from installing

the product yourself and contact our tech support for assistance. We

disclaim our liability for any damages to the product as well as incidental,

consequential, or indirect damages incurred due to improper or

inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Please carefully read the manual before beginning the

installation process.

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended

for liquid cooling systems, and mandatory for nickel-plated

water blocks.

Do not use pure distilled water! For best results, EK recommends

the use of EK-Cryo Fuel coolants.

Make sure to thoroughly bleed air out of your water block, or

you will not reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

BACKPLATE DIMENSIONS 5

PREPARING THE AM4 WATER BLOCK FOR UPGRADE 6

PREPARING THE AM5 MOTHERBOARD 7

INSTALLING THE WATER BLOCK 9

CONNECTING THE D-RGB LED STRIP 11

TESTING THE LOOP 11

WARRANTY 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

BOX CONTENTS

AM5 Backplate

Allen Key 2.5 mm (1 pc) TX20 L-Shaped Wrench (1 pc)

Thermal grease (1 pc)

- 5 -

BACKPLATE DIMENSIONS

90 mm

60 mm

43 mm

53 mm

8.9 mm

7.6 mm

6.3 mm

- 6 -

STEP 1

TOP OF THE

MOTHERBOARD

PREPARING THE AM4 WATER BLOCK FOR UPGRADE

Important! Before starting, make sure to have a clean, ﬂat

surface to work on. It is recommended to put foam or soft

material to lay a motherboard on.

STEP 1

If the EK-Quantum Velocity2 AM4 water block is already installed,

remove the backplate from the motherboard’s backside using Allen

Key 2.5 mm (As shown in the picture).

STEP 2

Detach the water block from the motherboard and save it for later

steps. Clean the CPU cold plate using a non-abrasive cloth or Q-tip.

STEP 2

- 7 -

STEP 1

Using a Philips-head screwdriver remove the four screws securing

the original plastic hold-down clamps around the socket as shown in

the illustration. Remove the hold-down clamps and store them away.

PREPARING THE AM5 MOTHERBOARD

UNC 6-32 SCREW

HOLD-DOWN

CLAMPS

STEP 1

STEP 2

After removing the plastic hold-downs, additional four (4) Screws

must be removed using provided TX20 L-shaped wrench. After

removing the screws, detach the factory-provided backplate. Save

the backplate screws for the next step.

STEP 2

BACKPLATE SCREW

FACTORY-PROVIDED

BAC KP L ATE

TX20 L-Shaped Wrench

For this step, you will need:

- 8 -

STEP 3

Attach the AM5 Backplate and secure it with the four (4) saved

backplate screws.

Do not peel off the protective sticker from the AM5 Backplate!

STEP 4

Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or

Q-tip as shown in the illustration.

STEP 3

STEP 4

IHS

NON-ABRASIVE CLOTH

AM5 BAC KP L ATE

BAC KP L ATE

SCREW

TX20 L-Shaped

Wrench

AM5 Backplate

Backplate screw

(4 pcs)

For this step, you will need:

- 9 -

STEP 1

Position the AM4 CPU Water Block onto the AM5 Motherboard.

Make sure to align the holes (as shown in the picture).

Make sure to double-check the layer of the Thermal Grease

before placing the water block onto the motherboard.

STEP 1

INSTALLING THE WATER BLOCK

STEP 5

Applying thermal compound: Apply the enclosed thermal grease

(thermal compound) on the CPU heat spreader – IHS – as shown in

the image. The layer of the thermal compound must be thin and even

in thickness over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 5

Thermal Grease

For this step, you will need:

- 10 -

STEP 3

With EK-Velocity² series water blocks, it is mandatory to use the

bottom port as the INLET.

Mixing the ports may result in poor thermal performance of the

water block.

Tighten the ﬁttings in a clockwise direction until the gasket

underneath is compressed. The installation of the Velocity² water

block is now complete.

OUTLET

INLET

STEP 2

Secure the water block from the backside of the motherboard using

the included Allen Key 2.5mm.

Start fastening the screws in a cross pattern. Do not tighten fully until

all of the screws are partially screwed in.

The Allen Key 2.5mm must be used in a standing position! Otherwise,

the mounting screws may crack during tightening!

Make sure to orientate the backplate as illustrated. Incorrect

installation of the backplate may result in damage to the motherboard.

Allen Key 2.5 mm

For this step, you will need:

MAX TORQUE:

0.6 Nm TOP OF THE

MOTHERBOARD

AM5

BAC KP L ATE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FC590 GTX Mode d’emploi

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series Manuel utilisateur

ekwb

ekwb EK-Pro Manuel utilisateur

ekwb

ekwb EK-FB MSI X399 GAMING RGB Monoblock Manuel utilisateur

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manuel utilisateur

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Manuel utilisateur

ekwb

ekwb EK-Classic GPU Water Block RTX 3080/3090... Manuel utilisateur

ekwb

ekwb EK-FC Titan V Manuel utilisateur

ekwb

ekwb EK-FC1080 GTX TF6 Backplate Manuel

ekwb

ekwb EK-FB GA 990FXA-UD7 Manuel

ekwb

ekwb EK-FC690 Mode d’emploi

ekwb

ekwb EK-Annihilator Pro ILM Series Manuel utilisateur

ekwb

ekwb ASUS Z9PE-D8 Manuel utilisateur

ekwb

ekwb EK-FB ASUS X58 Mode d’emploi

ekwb

ekwb EK-XRES 100 Revo D5 Series Manuel

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manuel utilisateur

ekwb

ekwb EK-FB ASUS PRIME X299 RGB Monoblock Manuel utilisateur

ekwb

ekwb EK-FC7970 Lightning Manuel

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Manuel utilisateur

ekwb

ekwb EK-FB KIT EVGA SR-X Manuel d'instructions d'installation

ekwb

ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... Manuel utilisateur

ekwb

ekwb EK-FC670 GTX DCII Mode d’emploi

ekwb

ekwb EK-Annihilator EX/EP Series Manuel utilisateur

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-Quantum Velocity 2 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques