EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Manuel utilisateur

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector² FTW3 RTX 3090 Ti ABP Set D-RGB

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced

or feel unsure about the installation procedure, please refrain from

installing the product yourself and contact our tech support for

assistance. We disclaim our liability for any damages to the product as

well as incidental, consequential, or indirect damages incurred due to

improper or inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always

recommended for liquid cooling systems and mandatory for

nickel-plated water blocks!

Do not use pure distilled water!

For best results, EK recommends the use of EK-CryoFuel

coolants! To reach optimal performance, make sure to

thoroughly bleed the air out of your water block!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

NICKEL PLEXI 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

PREPARING THE WATER BLOCK FOR INSTALLATION 8

CLEANING THE PCB 8

CUTTING AND PLACING THERMAL PADS 10

APPLYING THERMAL COMPOUND 11

ATTACHING THE WATER BLOCK 11

ATTACHING THE AC TIVE BACKPLATE 13

FITTINGS AND TUBING 15

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 15

CONNECTING THE D-RGB LED STRIP 16

TESTING THE LOOP 16

WARRANTY 17

SUPPORT AND SERVICE 18

SOCIAL MEDIA 18

- 4 -

BOX CONTENTS

4 mm

10 mm

EK-Loop Multi Allen Key (1 pc)

Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

Thermal Pad F 1.0 mm (8 pcs)

(3830046996732)

Thermal Pad F 1.5 mm (4 pc)

(3830046996749)

Thermal Pad G 2.0 mm (1 pcs)

(3830046996794)

Thermal Grease (1 pc)

M3x10 AX1 Screw (1 pc)

EK-Quantum Vector2FTW3 RTX

3090 Ti ABP Set D-RGB

M2.5x4 AX1 Screw (13 pcs)

Polyamid Washer M2.5 0.5mm (13 pcs) Terminal OR - Vector

14x1 mm (2 pcs)

120 mm

24 mm

120 mm

16 mm

120 mm

16 mm

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

EK-Plug Out Spludger Tool (1 pc)

Standoff M2.5-M3 x 6.6mm (1 pc) Nut M2.5 (2 pcs)

EAN: 105444

EAN: 104549

6 mm

M2.5x6 AX1 Screw (1 pc)

- 5 -

WATER BLOCK DIMENSIONS

95.9 mm

123.9 mm

318.2 mm

155 mm

142.5 mm

41 mm

35.5 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

- Dimensions: (LxHxW): 318.2 x 155 x 41 mm

- D-RGB LED count: 34

- D-RGB cable length: 50 cm

- D-RGB connector 3-pin 5V digital LED header

Position EAN Description Quantity

1105424 Coldplate (Nickel) 1

2103962 Top plate (Plexi) 1

3103987 Standoff M3.5-M2.5 x 3 5

4103988 Standoff M4-M2.5 x 3 4

5104106 Terminal OR 14 x 1 mm 4

6103942 Terminal badge 1

7105425 Top plate (Plexi) 1

89024 Screw M4 x 10 DIN7984 13

9103986 Standoff M3.5-M2.5 x 11.3 10

10 103964 Mylar sticker 2

11 105438 Stand out (Acetal) 1

12 100663 EK - Badge 2

13 105434 LED Cover (Nat.elox) 2

14 8208 Screw M3 x 8 7991DIN 2

15 5064 Main O-ring 140 x2 mm 1

16 104093 Standoff M2.5-M3 x 6.6 10

17 104105 Screw AX1 M3 x 10 10

18 104395 Terminal plate (Nickel) 1

19 104414 OR Terminal 52 x 2 mm 1

20 105163 Disc magnet 4

21 104086 ABP Terminal badge 1

22 104393 FC Terminal 1

23 8311 Screw M4 x 20 DIN7984 6

24 105441 Side plate (Black e.) 1

25 8201 Screw M3 x 10 7991DIN 2

26 105436 Coldplate ABP (Nickel) 1

27 105437 Top plate ABP (Plexi) 1

28 9013 Screw M4 x 8 DIN7984 13

29 5064 Main O-ring ABP 140 x 2 mm 1

30 100815 LED D-RGB strip 500/300 mm 2

31 105445 PCB cardboard 1

524

- 7 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Use the Phillips head screwdriver to remove the fifteen marked

screws and the Stock Cooler Backplate from the backside of the

GPU. Carefully detach the Stock Cooler Backplate from the PCB.

Use the Phillips head screwdriver to remove the nine marked

screws to detach the Stock Cooler from the PCB of the GPU.

Carefully detach the PCB from the stock cooler and disconnect all

cables connecting the stock cooler to the PCB.

Always remove the stock cooler slowly - it might be

firmly glued to the PCB with thermal pads.

For this step, you will need:

Phillips Head Screwdriver

STOCK BACKPLATE

- 8 -

PREPARING THE WATER BLOCK FOR INSTALLATION

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

STEP 2

STEP 1

First, remove the terminal badge which is attached to the terminal with

two magnets. Under the badge, unscrew three (3) screws M4 x 20

DIN7984. Additional ten (10) screws M3 x 10 AX1 need to be removed

(as shown in the image).

DO NOT REMOVE THE UPPER TERMINAL BADGE!

STEP 1

For this step, you will need:

Phillips Head Screwdriver

UPPER

TERMINAL

BADGE

TERMINAL

BADGE

M4 x 20 DIN7984

SCREW

M3 x 10 AX1 SCREW

DO NOT

REMOVE

THE UPPER

TERMINAL

BADGE!

Allen Key 2.5mm

- 9 -

STEP 2

Carefully remove the complete active backplate with the terminal.

Additional two (2) O-rings 14 x 1 EPDM50 need to be removed.

STEP 2

TERMINAL

O-RING 14 x 1 mm

ACTIVE

BACK PL AT E

STEP 3

M3.5-M2.5 x 11.3

STANDOFF

PCB

CARDBOARD

M2.5-M3 x 6.6

STANDOFF

STEP 3

Unscrew ten (10) M2.5-M3 x 6.6 standoffs with the included

tool (EK-Plug out Spludger Tool). Make sure not to unscrew the

M3.5-M2.5 x 11.3 standoff! In case the M3.5-M2.5 x 11.3 standoff

unscrews, carefully tighten it back with the 4 mm wrench.

After removing the standoffs, the PCB cardboard needs to be

removed. The PCB cardboard is printed on 1:1 scale.

For this step, you will need:

EK-Plug Out Spludger Tool

- 10 -

For this step, you will need:

Scissors

Thermal Pad G – 2.0 mm (120 x 24 mm)

120 mm

24 mm

2 mm

Thermal Pad - 120 x 16 x 1.0 mm

CUTTING AND PLACING THERMAL PADS

STEP 1

Our GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Replacement thermal pads:

Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

Thermal Pad F 1.5 mm – (120 x 16 mm) EAN: 3830046996749

Thermal Pad G 2.0 mm – (120 x 24 mm) EAN: 3830046996794

Thermal Pad F – 1.0 mm (120 x 16 mm)

120 mm

16 mm

1 mm

Thermal Pad F – 1.5 mm (120 x 16 mm)

1.5 mm

120 mm

16 mm

STEP 1

F1 F1 F1

Autres manuels pour Vector2 FTW3 RTX 3080 D-RGB

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels EK-Quantum Matériel informatique

EK-Quantum

EK-Quantum Vector FE RTX 3090 Ti D-RGB + Backplate Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manuel utilisateur

EK-Quantum

EK-Quantum Vector RX 6700XT Backplate Manuel utilisateur

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 Arc A750-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Momentum MSI Z590 Carbon D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Vector RTX 3080/3090 Backplate Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 XC3 RTX 3080 D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manuel utilisateur

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manuel utilisateur

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Vector FTW3 RTX 3080 Manuel utilisateur

EK-Quantum

EK-Quantum Vector RTX 3080/3090 Backplate Manuel utilisateur

EK-Quantum

EK-Quantum MSI MPG X670E CARBON EK X D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Vector FE RTX 3070 Ti D-RGB + Backplate Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum EK-Classic GPU Water Block Strix RTX 3070... Manuel utilisateur

EK-Quantum

EK-Quantum Velocity D-RGB - AMD Ryzen Edition Manuel utilisateur

EK-Quantum

EK-Quantum Momentum ROG Maximus XII Hero Manuel utilisateur

EK-Quantum

EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Manuel utilisateur

EK-Quantum

EK-Quantum Kinetic FLT Accent - Silver Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur