Dwyer Instruments 631 Series Manuel utilisateur

Series 631 Differential Pressure Transmitter

Specications - Installation and Operating Instructions

Bulletin E-114

The Series 631 Differential Pressure Transmitter monitors differential pressure

of air and compatible gases and liquids. The design employs converting pressure

changes into a standard 4-20 mA output signal for two wire circuits. Digital push-button,

zero and span adjustments are easily accessed on the front cover. The Series 631

Differential Pressure Transmitter is designed to meet NEMA-4X (IP66) construction.

INSTALLATION

1. Location: Select a location where the temperature of the unit will be between 20 and

120°F. Distance from the receiver is limited only by total loop resistance (see

electrical connections). The tubing feeding pressure to the instrument can be

practically any length required, but long lengths will increase the response time

slightly. Mount the instrument in a location that will not be subject to excessive

temperature, shock or vibration.

2. Position: A vertical position is recommended (pressure connections pointing

vertically) since that is how all standard models were originally spanned and

zeroed at the factory.

3. Pressure Connection: Dual 1/4˝ female NPT pressure connections are provided.

Use pipe thread sealant tape or other suitable pipe joint compound when making

connection to the pressure source. Avoid excess sealant which could block the

pressure passage. When monitoring liquid pressures, air trapped in the lines can

cause incorrect readings. Bleed ttings or similar mechanisms should be used to

bleed off any trapped air.

SPECIFICATIONS

Service: Compatible gases & liquids.

Wetted Materials: Brass, silicone, 300 SS.

Accuracy: Transmitter Output: ±2% F.S. (includes linearity, hysteresis and

repeatability); Gage: ±3% of full scale at 70°F (21.1°C).

Stability: ±1% F.S./yr.

Temperature Limits: 20 to 120°F (-6.67 to 48.9°C).

Pressure Limits: -20˝ Hg to 500 psig. (-0.677 bar to 34.4 bar).

Thermal Effect: Greater than 1˝ ranges: ±0.025%/°F (±0.045%/°C); 1˝ range:

±0.045%/°F (±0.081%/°C); 0.5˝ range: ±0.09%/°F (±0.162%/°C).

Power Requirements: 10-35 VDC.

Output Signal: 4 to 20 mA.

Response Time: 50 msec.

Loop Resistance: 0-1250 ohms maximum.

Electrical Connections: M-12 circular 4 pin connector.

Process Connections: 1/4˝ female NPT high and low pressure taps, duplicated -

one pair top for air and gas, and one pair bottom for liquids.

Enclosure Rating: Designed to meet NEMA 4X (IP66).

Mounting Orientation: Diaphragm in vertical position. Consult factory for other

position orientations.

Weight: 8 lb, 4 oz (3.74 kg).

Agency Approvals: CE.

[127.00]

4-45/64

[119.46]

3-13/32

[86.52]

13/32

[10.32] TYP 3/16

[4.76]

1/4 FEMALE NPT LOW

PRESSURE CONNECTION (LIQUID)

(4) #6-32 X 3/8 [9.53] DP

HOLE ON A 4-11/32 [110.33]

BOLT CIRCLE

1/4 FEMALE NPT HIGH

PRESSURE CONNECTION (LIQUID)

1/4 FEMALE NPT LOW

PRESSURE CONNECTION

(AIR OR GAS)

1/4 FEMALE NPT HIGH

PRESSURE CONNECTION

(AIR OR GAS)

3/4 [19.05] TYP

35° TYP

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

www.dwyer-inst.com

e-mail: [email protected]

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

www.dwyer-inst.com

e-mail: [email protected]

ELECTRICAL CONNECTIONS

CAUTION: Do not exceed specied supply voltage ratings. Permanent damage not

covered by warranty will result. This unit is not designed for 120 or 240 volt AC line

operation.

Wire Length - The Maximum length of wire connecting transmitter and receiver is a

function of wire size and receiver resistance. Wiring should not contribute to more than

10% of receiver resistance to total loop resistance. For extremely long runs (over 1000

ft.), choose receivers with higher resistance to minimize size and cost of connecting

leads. When the wiring length is under 100 feet, lead wire as small as 22 AWG can

be used.

Current (4 to 20 mA) Output Operation - An external power supply delivering 10-35

VDC with minimum current capability of 40 mA DC (per transmitter) must be used to

power the control loop. See Figure B for connection of the power supply, transmitter,

and receiver. The range of the appropriate receiver load resistance (RL) for the DC

power supply voltage available is expressed by the formula:

RL Max =

Shielded two wire cable is recommended for control loop wiring. If grounding is

required use negative side of control loop after receiver, see Figure B.

MULTIPLE RECEIVER INSTALLATION

An advantage of the standard 4 to 20 mA DC output signal provided by the Series 631

Differential Transmitter is that any number or receivers can be connected in series

in the current loop. Thus, an A-701 digital readout, an analog panel meter, a chart

recorder, process controlling equipment, or any combination of these devices can be

operated simultaneously. It is necessary only that each be equipped with a standard 4

to 20 mA input and proper polarity of the input connections be observed when inserting

the device into the current loop. If any of the receiving devices displays a negative or

downscale reading this indicates that the signal input leads are reversed.

MOUNTING OPTIONS

MAINTENANCE

Upon nal installation of the Series 631 Differential Pressure Transmitter and the

companion receiver, no routine maintenance is required. A periodic check of the

system calibration is recommended. The Series 631 Differential Pressure Transmitter

is not eld serviceable and should be returned if repair is needed (eld repair should

not be attempted and may void warranty). Be sure to include a brief description of the

problem plus any relevant application notes. Contact customer service to receive a

return goods authorization number before shipping.

SERIES 631

PRESSURE

TRANSMITTER

POWER

SUPPLY

10-35 VDC

RECEIVER

Figure A

Figure B

Vps – 10

20 mA DC

1/4 (6.35) HOLES IN PANEL

FOR BLOWOUT PASSAGE

3/4 (19.05) HOLE IN PANEL

FOR ELECTRICAL

CONNECTION

42 - TYP 2 PLACES

(4) 3/16 (4.76) HOLES IN PANE

EQUALLY SPACED ON A

4-11/32 (110.33) B.C.

SURFACE MOUNT HOLE PATTERN

This symbol indicates waste electrical products should not be disposed

of with household waste. Please recycle where facilities exist. Check with

your Local Authority or retailer for recycling advice.

Autres manuels Dwyer Instruments Émetteur

Dwyer Instruments

Dwyer Instruments Magnesense MS Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDX Series Supplément

Dwyer Instruments

Dwyer Instruments 641RM Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments Series CDTV Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 629HLP Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDWP Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 629 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments PMT2 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDT Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 641 series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDWP Deries Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 607 Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments AVUL Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CMT Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments AVUL Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments Series 616 Manuel utilisateur

Dwyer Instruments

Dwyer Instruments UL series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 629 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDTV Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments Dwyer AVUB Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments LOVE Iso Verter II SC478 Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 626 series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments Magnesense DWMS-112 Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments PHOTOHELIC 3000 SGT series Instructions d'installation et d'utilisation

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur