Dwyer Instruments CDT Series Manuel utilisateur

Series CDT and CDTR Duct Mount Carbon Dioxide/

Temperature/Relative Humidity Transmitter

Specications - Installation and Operating Instructions

Bulletin AQ-CDT/CDTR

Series CDT and CDTR Duct Mount Carbon Dioxide/ Temperature/Relative

Humidity Transmitters accurately monitor the CO2concentration and temperature

in schools, ofce buildings, and other indoor environments to help achieve LEED®

certication. For increased sensor life, a single- beam dual-wavelength non-dispersive

infrared (NDIR) sensor is used to automatically correct the measurement in both

occupied and unoccupied buildings against aging effects. The single-beam dual-

wavelength sensor technology provides the highest level of accuracy, compared to

Automatic Baseline Correction methods, which can unintentionally shift the calibration

based on CO2 levels and barometric pressure conditions. In order to achieve a higher

level of accuracy, the Series CDT includes digital barometric pressure adjustment and

the ability to eld-calibrate the sensor.

Universal outputs allow users to select the transmitter output to be 4 to 20 mA, 0 to

5 VDC or 0 to 10 VDC to work with virtually any building management controller. An

optional relay with user adjustable set points can be used to control exhaust fans, open

actuated windows or dampers, or signal a light or horn.

For applications that require visual indication, the Series CDT and CDTR can be

ordered with the Model A-449 remote LCD display that can plug into the mini-connector

port on the internal circuit board. Both the CDT and CDTR can be congured to display

temperature only, CO2only or CO2 and temperature together. The CDTR can also

display relative humidity or CO2 and relative humidity together. Menu items that can

be accessed include: engineering units, relay output set points, display conguration,

transmitter output scaling, ambient barometric pressure and eld calibration of the

transmitter.

Single-beam dual-wavelength sensor advantages:

• Automatically corrects for aging effects in occupied and unoccupied buildings

◦ Perfect for hospitals and manufacturing plants that are occupied 24 hours per

day

• Measures actual unltered light intensity directly

◦ Eliminates error from incorrect assumptions of gas concentration in theoretical

logic assumption methods

INSTALLATION

LEED® is a registered trademark of the U.S. Green Building Council

Disconnect power supply before installation to prevent electrical

shock and equipment damage.

Make sure all connections are in accordance with the job wiring diagram and in

accordance with national and local electrical codes. Use copper conductors only.

Use electrostatic discharge precautions (e.g., use of wrist straps)

during installation and wiring to prevent equipment damage.

Avoid locations where severe shock or vibration, excessive

moisture or corrosive fumes are present.

Do not exceed ratings of this device, permanent damage not

covered by warranty may result.

Upon powering the transmitter, the rmware version will ash on

the display. A warm up period of 30 minutes is required for the

transmitter to adjust to the current CO2 concentration.

Self calibration feature of the transmitter requires exposure to

normal outdoor equivalent carbon dioxide level once every thirty

days.

NOTICE

SPECIFICATIONS

Range: CO2: 0 to 2000 or 0 to 5000 ppm (depending on model); RH: 0 to 100% (for

units congured with humidity output); Temperature: 32 to 122°F (0 to 50°C).

Accuracy: ±40 ppm + 3% of reading (CO2); RH: ±2% (for units congured with

humidity output); Temperature: ± 1°C @ 25°C.

Temperature Dependence: ±8 ppm / °C at 1100 ppm.

Non-Linearity: 16 ppm.

Pressure Dependence: 0.13% of reading per mm of Hg.

Response Time: 2 minutes for 99% step change.

Temperature Limits: 32 to 122°F (0 to 50°C).

Humidity Limits: 10 to 95% RH (non-condensing).

Power Requirements: 16 to 35 VDC / 19 to 28 VAC.

Power Consumption: Average: 2 watts; Peak: 3.75 watts.

Sensor: Single-beam, dual-wavelength NDIR.

Output: Current: 4 to 20 mA (max 500 Ω); Voltage: 0 to 5 VDC or 0 to 10 VDC

(min 500 Ω); Relay: SPST NO 2A @ 30 VDC; RTD or thermistor per r-t curves

(depending on model).

Weight: 5.6 oz (158.8 g).

Agency Approvals: CE.

WARNING

CAUTION

1/8˝

[3.17]

4-25/32˝

[121.44]

4-9/32˝

[108.74] 2-13/16˝

[71.44]

Ø3-5/16˝

[84.14]

11-49/64˝

[298.85]

Ø1-15/64˝

[31.35]

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

www.dwyer-inst.com

e-mail: [email protected]

MOUNTING

1. Cut hole into duct large enough to insert probe.

2. Attach housing ears to duct using the two self-tapping screws provided.

3. Knock out an opening in the housing and attach an electrical tting to route

electrical wiring. PG11 & PG16 knockouts are molded into the housing.

WIRING

Use maximum 18 AWG wire for wiring to terminals. Refer to Figure 5 for wiring

information.

Selection of Current and Voltage Outputs

Prior to wiring, verify that the current/voltage conguration switches (positions 1 and 2)

are set to the desired output type. Refer to Figure 1 to locate the conguration switches.

See Figure 2 for diagram of the current/voltage selection switches. For voltage output

selection, the output can be 0 to 10 VDC, 0 to 5 VDC, 2 to 10 VDC or 1 to 5 VDC. See

Figure 3 for the type of voltage output selection switches (positions 3 & 4).

Current / Voltage Outputs

The transmitter may be wired for current or voltage output for both carbon dioxide and

temperature. The transmitter can be powered with either 16 to 35 VDC or 19 to 28

VAC. Wire the transmitter according to Figure 4.

Thermistor and RTD Outputs

Thermistor and RTD passive outputs are located on terminals 7 and 8 and do not

require any power. Passive temperature outputs are not polarity sensitive.

Remote Display

Remote display Model A-449 can be used to display the relative humidity, temperature,

and carbon dioxide. The mini USB plug of the remote display plugs into the receptor on

the side of the housing. After a short warm up time, the display will begin to show the

current temperature and carbon dioxide measurements unless congured by the user

to show only temperature or only carbon dioxide.

ACCESSING MENU PARAMETERS

Step 1: To enter the menu structure, press and simultaneously for 5

seconds (display will show RON parameter).

Step 2: Press or to cycle between menu items.

Step 3: Press to edit the value for the displayed menu item (SET will appear on

display).

Step 4: Press or to adjust the value of the menu item.

Step 5: Press to save the changes (SET will disappear).

Step 6: Repeat Steps 2 through 5 for each of the parameters.

Step 7: To exit the menu at any time, press and hold and simultaneously

for 5 seconds or wait 10 seconds without pushing any buttons.

PASSIVE

TEMPERA

TURE

SENSOR

RELAY

CONTACT

POWER

SUPPLY

TEMP OR RH

RECEIVER

CO2

RECEIVER

Figure 4: Active Output Wiring Diagram

Figure 1: Diagram Of Circuit Board

Figure 2: Current/Voltage Output

Selection Jumper (PJ1 And PJ2)

Figure 3: Output Range Selection Jumper

Optional relay can be used as either a dry contact or low voltage

switched circuit up to 2 A at 30 VDC.

NOTICE

DOWN PUSH

BUTTON

CONFIGUATION

SWITCHES TERMINAL

BLOCK

REMOTE DISPLAY

CONNECTOR

UP PUSH BUTTON

ENTER PUSH BUTTON

CO2 CONCENTRATION

OUTPUT SELECTION

TEMPERATURE/

RH OUTPUT SELECTION

VOLTAGE CURREN

TVO

LTAGE CURRENT

0-10 V

0-20 mA

2-10 V

4-20 mA

0-5 V

0-10 mA

1-5 V

2-10 mA

Relay on set point

Sets the CO2 concentration which the optional relay is energized.

Low limit: 0 PPM

Factory setting: 1000 PPM

High limit: 2000/5000 PPM (depending on model)

Relay off set point

Sets the CO2 concentration which the optional relay is de-energized. Setting

value lower than RON provides direct action for detecting high concentrations

of CO2. Setting value higher than RON provides indirect action for detecting

low concentrations of CO2. or on the LCD display will be lit to

indicate when the relay is energized.

Low limit: 0 PPM

Factory setting: 950 PPM

High limit: 2000/5000 PPM (depending on model)

Display conguration

Determines the LCD display conguration during normal operation. The LCD

display can indicate the CO2 concentration, temperature, relative humidity

(CDTR only) and CO2 concentration combined with temperature or relative

humidity (CDTR only).

CH CO

2 concentration and relative humidity (CDTR only)

CT CO

2concentration and temperature

C CO2concentration only

T Temperature only

H Relative humidity only (CDTR only)

Units selection

Temperature and barometric pressure measurements can be displayed in US

engineering units or SI engineering units. The factory default is to display US

engineering units.

US units °F for temperature and in Hg for barometric pressure

SI units °C for temperature and hPa for barometric pressure

CO2 low output range

Sets the CO2 concentration for the lowest output (4 mA or 0 VDC).

Low limit: 0 PPM

Factory setting: 0 PPM

High limit: 2000/5000 PPM (depending on model)

CO2 high output range

Sets the CO2 concentration for the highest output (20 mA, 5 VDC or 10 VDC).

When COH is set above COL, the transmitter is direct acting and the output

will increase with an increase in CO2 level. When COH is below COL, the

transmitter is reverse acting and the output will increase with a decrease in

CO2 level.

Low limit: 0 PPM

Factory setting: 2000/5000 PPM (depending on model)

High limit: 2000/5000 PPM (depending on model)

RON

ROF

DSP

UNI

COL

COH

TOL

TOH

HOL

HOH

BAR

CAL

Temperature low output range (CDT with active temperature only)

Sets the temperature for the lowest output (4 mA or 0 VDC).

Low limit: 32.0°F / 0.0°C

Factory setting: 32.0°F / 0.0°C

High limit: 122.0°F / 50.0°C

Temperature high output range (CDT with active temperature only)

Sets the temperature for the highest output (20 mA, 5 VDC or 10 VDC).

When TOH is set above TOL, the transmitter is direct acting and the output

will increase with an increase in temperature. When TOH is below TOL, the

transmitter is reverse acting and the output will increase with a decrease in

temperature.

Low limit: 32.0°F / 0.0°C

Factory setting: 122.0°F / 50.0°C

High limit: 122.0°F / 50.0°C

Humidity low output range (CDTR only)

Sets the temperature for the lowest output (4 mA or 0 VDC).

Low limit: 0.0%

Factory setting: 0.0%

High limit: 100.0%

Humidity high output range (CDTR only)

Sets the temperature for the highest output (20 mA, 5 VDC or 10 VDC).

When HOH is set above HOL, the transmitter is direct acting and the output

will increase with an increase in temperature. When HOH is below HOL, the

transmitter is reverse acting and the output will increase with a decrease in

temperature.

Low limit: 0.0%

Factory setting: 100.0%

High limit: 100.0%

Barometric pressure

Sets the typical barometric pressure for the location where the transmitter is

mounted. The factory setting is for standard pressure at sea level. Adjusting the

barometric pressure gives a more accurate measurement, especially at higher

elevations. Refer to the elevation charts in Figure 9 for typical barometric

pressures at a given elevation.

Low limit: 20.0 in Hg / 600 hPa

Factory setting: 29.9 in Hg / 1013 hPa

High limit: 32.0 in Hg / 1100 hPa

Calibration

Calibrates the carbon dioxide sensor to a known gas value. Read calibration

instructions before using this feature. Hold for 5 seconds.

Menu Descriptions

CALIBRATING SENSOR

Step 1: Remove the cover as shown in Figure 1.

Step 2: Slide the calibration tubing through the slots on the back plate and attach to

one of the nipples on the CO2 sensor (See Figure 7).

Step 3: Carefully re-attach the cover to the back plate without pinching the tubing

between the back plate and the cover.

Step 4: Follow the steps in the accessing parameter section to access the

calibration parameter (CAL).

Step 5: Press the button.

Step 6: Flow zero reference gas at 0.3 SLPM for 5 minutes.

Step 7: Press and hold the button for 3 seconds.

Step 8: Flow the full scale reference gas at 0.3 SLPM for 5 minutes.

Step 9: Press and hold the button for 3 seconds.

Step 10: Exit the parameter menu.

Step 11: Remove cover as shown in Figure 1.

Step 12: Remove tubing from sensor and re-attach the gas nipple cover to the sensor.

Step 13: Re-attach the cover to the back plate.

MAINTENANCE/REPAIR

Upon nal installation of the Series CDT/CDTR, no routine maintenance is required.

The Series CDT/CDTR is not eld serviceable and should be returned if repair is

needed. Field repair should not be attempted and may void warranty.

WARRANTY/RETURN

Refer to “Terms and Conditions of Sales” in our catalog and on our website. Contact

customer service to receive a Return Goods Authorization number before shipping the

product back for repair. Be sure to include a brief description of the problem plus any

additional application notes.

Series CDT -2 D4 4 -RLY Example: CDT-2D44-LCD

Range 2

0 to 2000 ppm CO2 range

0 to 5000 ppm CO2 range

Conguration D Duct

CO2 Output 4 4 to 20 mA / 0 to (5 or 10) VDC

Temperature

Output

None

4 to 20 mA / 0 to (5 or 10) VDC

10 KΩ NTC thermistor type III

10 KΩ NTC thermistor type II

3 KΩ NTC thermistor

Pt100 Ω RTD

Pt1000 Ω RTD

20 KΩ NTC thermistor

Options RLY Relay

US Customary Units

ft in Hg

400

800

1200

1600

2000

2400

2800

3200

3600

4000

4400

4800

5200

5600

6000

6400

6800

7200

7600

8000

8400

8800

9200

9600

10000

29.92

29.50

29.10

28.69

28.29

27.90

27.51

27.13

26.76

26.39

26.02

25.66

25.30

24.95

24.60

24.26

23.93

23.60

23.27

22.94

22.63

22.31

22.00

21.70

21.40

SI Units

mhPa

100

200

300

400

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

2100

2200

2300

2400

2500

1013

1002

990

979

968

957

946

935

924

914

904

893

883

873

863

853

844

834

824

815

806

797

787

779

770

761

Series CDTR -2 D4A4 -RLY Example: CDTR-2D4A4-LCD

Range 2

0 to 2000 ppm CO2 range

0 to 5000 ppm CO2 range

Conguration D Duct

CO2 Output 4 4 to 20 mA / 0 to (5 or 10) VDC

Temperature

Output

None

10 KΩ NTC thermistor type III

10 KΩ NTC thermistor type II

3 KΩ NTC thermistor

Pt100 Ω RTD

Pt1000 Ω RTD

20 KΩ NTC thermistor

RH Output 4 4 to 20 mA / 0 to (5 or 10) VDC

Options RLY Relay

Temperature Resistance Curves (in Ohms)

°C °F A B C D E F

-55

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

100

105

110

115

120

125

130

135

140

145

150

-67.0

-58.0

-49.0

-40.0

-31.0

-22.0

-13.0

-4.0

5.0

14.0

23.0

32.0

41.0

50.0

59.0

68.0

77.0

86.0

95.0

104.0

113.0

122.0

131.0

140.0

149.0

158.0

167.0

176.0

185.0

194.0

203.0

212.0

221.0

230.0

239.0

248.0

257.0

266.0

275.0

284.0

293.0

302.0

607800.00

441200.00

323600.00

239700.00

179200.00

135200.00

102900.00

78910.00

61020.00

47540.00

37310.00

29490.00

23460.00

18780.00

15130.00

12260.00

10000.00

8194.00

6752.00

5592.00

4655.00

3893.00

3271.00

2760.00

2339.00

1990.00

1700.00

1458.00

1255.00

1084.00

939.30

816.80

712.60

623.60

547.30

481.80

425.30

376.40

334.00

297.20

265.10

237.00

963849.00

670166.00

471985.00

336479.00

242681.00

176974.00

130421.00

97081.00

72957.00

55329.00

42327.00

32650.00

25392.00

19901.00

15712.00

12493.00

10000.00

8057.00

6531.00

5326.00

4368.00

3602.00

2986.00

2488.00

2083.00

1752.00

1480.00

1255.00

1070.00

915.50

786.60

678.60

587.60

510.60

445.30

389.60

341.90

301.00

265.80

235.30

208.90

186.10

289154.70

201049.80

141595.50

100943.70

72804.30

53092.20

39126.30

29124.30

21887.10

16598.70

12698.10

9795.00

7617.60

5970.30

4713.60

3747.90

3000.00

2417.10

1959.30

1597.80

1310.40

1080.60

895.80

746.40

624.90

525.60

444.00

376.50

321.00

274.65

235.98

203.58

176.28

153.18

133.59

116.88

102.57

90.30

79.74

70.59

62.67

55.83

78.32

80.31

82.29

84.27

86.25

88.22

90.19

92.16

94.12

96.09

98.04

100.00

101.95

103.90

105.85

107.79

109.74

111.67

113.61

115.54

117.47

119.40

121.32

123.24

125.16

127.08

128.99

130.90

132.80

134.71

136.61

138.51

140.40

142.29

144.18

146.07

147.95

149.83

151.71

153.58

155.46

157.33

783.2

803.1

822.9

842.7

862.5

882.2

901.9

921.6

941.2

960.9

980.4

1000.0

1019.5

1039.0

1058.5

1077.9

1097.4

1116.7

1136.1

1155.4

1174.7

1194.0

1213.2

1232.4

1251.6

1270.8

1289.9

1309.0

1328.0

1347.1

1366.1

1385.1

1404.0

1422.9

1441.8

1460.7

1479.5

1498.3

1517.1

1535.8

1554.6

1573.3

2394000.00

1646200.00

1145800.00

806800.00

574400.00

413400.00

300400.00

220600.00

163500.00

122280.00

92240.00

70160.00

53780.00

41560.00

32340.00

25360.00

20000.00

15892.00

12704.00

10216.00

8264.00

6722.00

5498.00

4520.00

3734.00

3100.00

2586.00

2166.00

1822.60

1540.00

1306.40

1112.60

951.00

815.80

702.20

606.40

525.60

N/A

Figure 5: CDT Model Chart

Figure 7: Elevation Chart

Figure 8: Resistance vs Temperature

RESISTANCE VS TEMPERATURE TABLE

Figure 6: CDTR Model Chart

This symbol indicates waste electrical products should not be disposed

of with household waste. Please recycle where facilities exist. Check with

your Local Authority or retailer for recycling advice.

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

dwyer-inst.com

e-mail: [email protected]

Ce manuel convient aux modèles suivants

Autres manuels Dwyer Instruments Émetteur

Dwyer Instruments

Dwyer Instruments CDX Series Supplément

Dwyer Instruments

Dwyer Instruments 607 Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments CMT200 Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments IEF Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 629 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 608 Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments AVLV Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments Magnesense II MS2 Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments Dwyer AVUB Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 626 series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments Magnesense II MS2-X102 Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 634ES Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 629 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments CDWP Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments CDT Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments AVPT Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments GSTA Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments 629HLP Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments DM-2000 Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments IEF Series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments 616W Series Manuel utilisateur

Dwyer Instruments

Dwyer Instruments DPT series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments RHP-W series Instructions d'installation et d'utilisation

Dwyer Instruments

Dwyer Instruments UL series Instructions d'installation et d'utilisation

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur