DMP Electronics Thinline Series Guide d'installation

INSTALLATION AND PROGRAMMING GUIDE

7360/7363 Thinline

Series Icon Keypads

1 2 3 4

5 6 7 8

9 0 CMD

ALL RESET HOME CODE

CHIME PERIM SLEEP EXIT

ZONE OUTPUT TEST INST

About the 7360/7363 ................................ 1

Card Reader............................................................ 1

Proximity Credentials Compatibility............. 1

7360/7363 Features...................................2

Install the 7360/7363 ................................3

Remove the Cover............................................... 3

Wire the Keypad.................................................. 4

Install the System Information Reference

Card .......................................................................... 4

Mount the Keypad............................................... 4

Additional information ..............................6

Additional Power Supply.................................. 6

Panic Key Options............................................... 6

Internal Speaker Operation ............................. 7

Backlighting........................................................... 7

Program the Keypad ..................................8

End-User Options................................................ 8

Backlighting Brightness (b 8) ........................ 8

Internal Speaker Tone (S 5) ............................ 8

TABLE OF CONTENTS

Internal Volume Level (L 8) ............................ 9

Software Version (100) .................................... 9

Keypad Model Number .................................... 9

Installer Options Menu .....................................10

Panic Keys (P 0)..................................................10

Emergency Key (E 0) ....................................... 11

Fire Key (F 0) .......................................................11

Number of User Code Digits (U 4) from

Proximity Card Read (7363) ...........................11

Keypad Diagnostics........................................... 12

Keypad Bus Wiring Speciﬁcations......... 13

Product Speciﬁcations ............................ 14

Ordering Information............................... 14

Certiﬁcations............................................. 15

Accessories................................................ 16

FCC Information ....................................... 17

Industry Canada Information.................. 18

Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 1

The DMP Thinline™ Series Icon Keypads provide an easy to understand icon display to

assist users when arming and disarming an All/Perimeter or Home/Sleep/Away system or

using any of the standard system features. The icons provide immediate recognition of any

system alarm as well as system status.

The Model 7360 provides three 2-button Panic keys, backlit keyboard with easy-to-read

lettering and an internal speaker.

Card Reader

The Model 7363 also provides a built-in

proximity reader designed to read standard

HID proximity credentials. When a proximity

credential is presented to the internal reader,

a beep tone is heard to provide an audible

acknowledgement of the credential read.

Proximity Credentials

Compatibility

DMP Keypads with internal proximity

readers are compatible with most standard

125Khz Prox credentials available from all

DMP proximity credentials. DMP does not

guarantee compatibility with credentials not

purchased from DMP.

ABOUT THE 7360/7363

2 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.

7360/7363 FEATURES

Figure 1: Thinline Series Icon Keypad

1 2 3 4

5 6 7 8

9 0 CMD

ALL RESET HOME CODE

CHIME PERIM SLEEP EXIT

ZONE OUTPUT TEST INST

Display

Select Keys

Credential Reader

Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 3

INSTALL THE 7360/7363

Remove the Cover

1. Insert a ﬂat screwdriver into

one of the slots on the bottom

of the keypad and gently lift

the screwdriver handle toward

you while pulling the halves

apart. See Figure 2. Repeat

with the other slot.

2. Using your hands, gently

separate the front from the

base and set the front and

components aside.

Figure 2: Removing Cover

Cover

Base

4 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.

Wire the Keypad

The 7360 and 7363 keypads are supplied with a 4-wire harness for panel keypad bus

connection. Since all 7300 Series keypads operate together on the Keypad bus using

the same address, there is no address option to set.

Observe wire colors when connecting the Red, Yellow, Green, and Black wires to the

keypad bus.

When wiring directly to the panel terminals:

1. Connect Red to panel terminal 7.

2. Connect Yellow to terminal 8.

3. Connect Green to terminal 9.

4. Connect Black to terminal 10.

Install the System Information Reference Card

User Code instructions are on one side of the card and the opposite side oers an

area to record zone numbers and names. Figure 3 shows the location of the pull-out

card holder on the back of the keypad.

While the keypad is attached to the wall, insert the bottom of the card at an angle to

align the card into the bottom slot, then slide the card in place.

Mount the Keypad

All DMP keypad housings are designed to easily install on any 4” square box, 3-gang

switch box, DMP 695 and 696 backbox, or ﬂat surface.

Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 5

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

Reference Card

Guide Tabs

Surface and Backbox Mounting Holes

Combined 4-square and 3-gang Switch Box Mounting Holes

Keypad Back

Figure 3: Keypad Back with Wiring Harness

6 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.

ADDITIONAL INFORMATION

Additional Power Supply

If the current draw for all keypads exceeds the panel output, provide additional current by

adding a Model 505-12 auxiliary power supply. Connect all keypad Black ground wires to

the power supply negative terminal. Run a jumper wire from the power supply negative

terminal to the panel common ground terminal. Connect all keypad power (+12 VDC) wires

to the power supply positive terminal. Do not connect the power supply positive terminal

to any panel terminal. Refer to the 505-12 Power Supply Installation Guide (LT-0453) for

more information.

Panic Key Options

2-Button Panic Keys

All keypads oer a panic key function that allows users to send Panic, Emergency, or Fire

reports to the central station. In order to use the panic keys, enable the functions in the

keypad user menu. See Programming Keypad Options later in this document. Install the

supplied icon labels below the top row of Select keys as shown in Figure 4.

Press and hold the two Select keys for two seconds until a beep from the keypad is heard.

At the beep, the panel sends the zone alarm reports shown in Table 1to the central station.

Note: All 7300 keypads send address 8 as a default on panic alarms.

Autres manuels pour Thinline Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DMP Electronics Clavier

DMP Electronics

DMP Electronics 7000INT Series Guide d'installation

DMP Electronics

DMP Electronics 7872 Manuel utilisateur

DMP Electronics

DMP Electronics Thinline 7060 Instructions de montage

DMP Electronics

DMP Electronics 9800 Series Manuel utilisateur

DMP Electronics

DMP Electronics 7800 International Series Guide d'installation

DMP Electronics

DMP Electronics Thinline Aqualite 7000 Series Guide d'installation

DMP Electronics

DMP Electronics 691 Manuel utilisateur

DMP Electronics

DMP Electronics 7872 Manuel utilisateur

DMP Electronics

DMP Electronics 781 Manuel utilisateur

DMP Electronics

DMP Electronics 7800 Series Guide d'installation

DMP Electronics

DMP Electronics 791 Easy Entry Instructions de montage

DMP Electronics

DMP Electronics 9800 Series Manuel utilisateur

DMP Electronics

DMP Electronics Thinline 7463 Guide d'installation

DMP Electronics

DMP Electronics 532XR Manuel utilisateur

DMP Electronics

DMP Electronics 7800 Series Guide d'installation

DMP Electronics

DMP Electronics Thinline 7060 Manuel utilisateur

DMP Electronics

DMP Electronics 9800INT Series Guide d'installation

DMP Electronics

DMP Electronics Thinline 7060 Manuel utilisateur

DMP Electronics

DMP Electronics Aqualite 7560A Manuel utilisateur

DMP Electronics

DMP Electronics 692F Instructions de montage

DMP Electronics

DMP Electronics Security Command 670-A Manuel utilisateur

DMP Electronics

DMP Electronics easy entry 791 Manuel utilisateur

DMP Electronics

DMP Electronics 7760 Manuel utilisateur

DMP Electronics

DMP Electronics 9863 Manuel utilisateur

Manuels Clavier populaires d'autres marques

BFT

BFT SELETTO Manuel utilisateur

Micro Id

Micro Id MP7G3BL Manuel d'instructions

WindowMaster

WindowMaster WLI 130 Manuel utilisateur

ACT

ACT ACT PRO 1030 Manuel utilisateur

Cardin

Cardin SSB Series Manuel utilisateur

Harman Kardon

Harman Kardon KP 1 Manuel utilisateur

Chamberlain

Chamberlain KPR2000 Guide de l'utilisateur

CYP

CYP CR-KP1 Manuel utilisateur

Aeware

Aeware k-35 Series Guide de référence

Aritech

Aritech CS-175 Series Manuel utilisateur

GE NetworX NX-1600E Series Manuel utilisateur

Lenze AC Tech

Lenze AC Tech MC SERIES Manuel utilisateur

Burg Wächter

Burg Wächter secuENTRY 7711 Manuel utilisateur

Aeware

Aeware in.k450 Manuel utilisateur

Lenze

Lenze EPM-H410 Manuel utilisateur

Toshiba

Toshiba RKP007Z Manuel utilisateur

Gemini

Gemini GEM-DXK1 KEYPAD Manuel utilisateur

Russound

Russound MDK-C5 Manuel d'utilisation