DMP Electronics Thinline 7060 Manuel utilisateur

InstallatIon GuIde

Thinline™ LCD Keypads

Models 7060, 7063, 7070, 7073,

7160, 7163, 7170, 7173

Aqualite™ LCD Keypads

Models 7060A, 7063A, 7070A, 7073A

32-Character Display

Armed LED

Power LED

Data Entry Digit keys

COMMAND Key

Back Arrow Key

Select Keys

JONES RESIDENCE

FRI 12:51 PM

Backlit Logo

and Proximity

Antenna

32-Character Display

Armed LED

Power LED

Data Entry Digit keys

COMMAND Key

Back Arrow Key

Select Keys

ABC PRINTING

FRI 2:51 AM

1 2 3 4

9 0 CMD

5 6 7 8

Thinline/Aqualite Keypads

7000 Series

Thinline Keypad

7100 Series

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

LCD Keypad Installation Guide 1

DMP Keypad Features

The DMP Thinline™ and Aqualite™ LCD Keypads offer exible features and

functionality in stylish design choices.

Each keypad provides:

• Custom 16-character home or business name

• Four 2-button Panic keys

• AC power LED

• Armed LED

• 32-character display

• Backlit keyboard with easy-to-read lettering

• Internal speaker.

• Keyboard and logo backlighting turns Red in alarm conditions

• Simple harness connection to 4-wire keypad bus

• Optional backboxes for conduit or wall-mount applications

• The Thinline and Aqualite logo is also backlit.

The Models 7070/7070A, 7073/7073A, and 7170/7173 keypads provide four fully

programmable Class B, Style A, supervised, power limited protection zones you can

program for a variety of burglary and access control applications.

The Model 7063/7063A, 7073/7073A, and 7163/7173 keypads provide a built-in

proximity card reader designed to read DMP/HID proximity credentials.

The Model 7073/7073A/7173 keypads provide a door strike relay and allow Wiegand

input from external card readers.

2 LCD Keypad Installation Guide

Installing the Keypad

All DMP keypad housings are designed to easily install on any 4” square box, 3-gang

switch box, DMP 695 and 696 backbox, or a at surface. Figure 1 shows the keypad

housing base mounting hole locations.

Remove the Cover

The keypad housing is made up of two parts: the front, which

contains the circuit board and keyboard components and the

base. Use the following steps and gures to separate the keypad

front and base.

1. Insert a at screwdriver into one of the slots on the bottom

of the keypad and gently lift the screwdriver handle toward

you while pulling the halves apart. Repeat with the other

slot.

2. Using your hands, gently separate the front from the base

and set the front and components aside.

Harness Wiring

Figure 1 shows wiring harness assignments. Observe wire colors when connecting the

red, yellow, green, and black wires to the keypad bus. Connect red to panel terminal

7, yellow to terminal 8, green to 9, and black to panel terminal 10. Use 1k Ohm EOL

resistors, DMP Model 311, on keypad zones 1 through 4.

The 7060/7060A, 7063/7063A, and 7160/7163 keypads are supplied with a 4-wire

harness for panel keypad bus connection.

The 7070/7070A, 7073/7073A, and 7170/7173 keypads are supplied with a 12-wire

data bus/zone harness. Four wires connect to the keypad bus. The remaining eight

wires are for the four zone inputs: two wires for each zone.

The 7073/7073A/7173 keypads come with one 5-wire output/reader harness.

Additional Power Supply

If the current draw for all keypads exceeds the panel output, provide additional

current by adding a Model 505-12 auxiliary power supply. Connect all keypad black

ground wires to the power supply negative terminal. Run a jumper wire from the

power supply negative terminal to the panel common ground terminal. Connect all

keypad power (+12 VDC) wires to the power supply positive terminal. Do NOT connect

the power supply positive terminal to any panel terminal. Refer to the 505-12 Power

Supply Installation Guide (LT-0453).

Lift screwdriver

handle up

toward you to

separate keypad

cover from base.

Thinline

or Aqualite

Keypad

Building Wall

LCD Keypad Installation Guide 3

Keypad Bus Monitor

For listed re protective systems, the 893A Module or 277 Trouble Sounder must be

installed in the XR100/XR500 Series or XR150/XR350/XR550 Series control panel to

monitor the keypad bus and sound an audible trouble whenever the keypad bus fails

to operate. Refer to the 893A Module Installation Sheet (LT-0135) or 277 Trouble

Sounder Installation Sheet (LT-1304).

Card Readers

When a proximity credential is presented to an internal or external reader, a beep

tone is heard and the Power and Armed LEDs blink. This provides both an audible and

visual acknowledgement of the credential read.

Internal Access Control Reader

The 7063/7063A, 7073/7073A, and 7163/7173 keypads provide a built-in proximity

card reader designed to read DMP/HID 1300 Series proximity credentials.

Note: For listed access control applications, the keypad must be installed within

the protected area.

External Access Control Reader

To accept Wiegand data input from other external card readers, connect a

12 VDC external reader to the 7073/7073A/7173 keypad. Connect the Red and Black

power wires from the reader to the power wires from the panel. These connect in

parallel with the keypad power wires. Connect the Reader (Data 1) wire to the White

wire on the 5-wire keypad harness. Connect the Reader (Data 0) wire to the Green/

White wire on the 5-wire keypad harness. See Figure 2.

1K EOL

Green/White– Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3

– Zone 2

– Zone 1

External

Reader/

Door Strike

7073/7073A

7173 Keypads

All Keypads

Zones

1 through 4

7070/7070A,

7073/7073A,

and 7170/7173

Keypads

Surface and Backbox

Mounting Holes

Combined 4-square

and 3-gang switch box

Mounting Holes

Keypad Back

Surface and Backbox

Mounting Holes

All zones are supervised and suitable for fire applications

Maximum zone line impedence 100 Ohms

Ground fault detected at 1420 Ohms or less

Figure 1: Keypad Back Showing Wiring Harness Assignments

4 LCD Keypad Installation Guide

1K EOL

Green/White – Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3 Request to Exit (option)

– Zone 2 Door Contact (option)

– Zone 1 7/0 Panic (option)

To Keypad Bus

External Card

Reader

Figure 2: 12 VDC Reader Wiring

Door Strike Relay Specications

The 7073/7073A/7173 keypads provide one internal programmable Form C single

pole, double throw (SPDT) relay for controlling door strikes or magnetic locks. Three

wires on the 5-wire harness, Violet (N/C), Gray (Com), and Orange (N/O), allow you

to connect devices to the relay. The Form C relay draws up to 15mA of current and

the contacts are rated for 1 Amp resistance at 30 VDC maximum.

Wiring the 333 Suppressor

One Model 333 Suppressor is

included with the 7073/7073A,

7173 keypads. If the device being

controlled by the relay is connected

to the N/O and C wires, install the

suppressor on the N/O and C wires.

If the device is connected to the

N/C and C wires, install the 333 on

N/C and C wires. Refer to Figure 3.

Door Strike Relay Operation

As soon as the user code sent

from the reader is veried by the

panel, the keypad door strike relay

activates for 5 seconds. During this time, the access door connected to Zone 2 must

be opened to start the programmed entry/exit timer and zone Bypass.

Note: The 5-second door strike is programmable in the panel when the keypad is used

on a XR100/XR500 Series or XR150/XR350/XR550 Series panel. Refer to the panel

programming guide.

Model 333

Supressor

Common

– +

Magnetic Door Lock

DMP 502 or 505

Power Supply

Normally Open

Green/White – D0

White – D1

Orange – N/O

Gray – C

Violet –N/C

N/O

N/C

Normally

Closed

Keypad

5-Wire Harness

Figure 3: 5-wire Harness/Suppressor Installation

LCD Keypad Installation Guide 5

Zone 2 Door Contact with Bypass

If the door being released by the 7073/7073A/7173 keypad is protected, you can

provide a programmed bypass time by connecting its contact to Zone 2 (White/Red

pair) on the keypad and enabling the Bypass feature. See ZONE 2 BYPASS later in this

document. Door contacts may be N/C or N/O.

Note: The Door Strike time is programmable when the keypad is used on a

XR100/XR500 Series or XR150/XR350/XR550 Series panel.

Zone 3 Request to Exit

You can also connect a N/O PIR (or other motion sensing device) or a mechanical

switch to Zone 3 (White/Orange pair) on the 7073/7073A/7173 keypad to provide

request to exit capability. See ZONE 3 EXIT later in this document. When Zone 3

shorts, the keypad relay activates for 5 seconds. During this time, the user can open

the protected door to start the programmed Bypass entry/exit timer. If the door is

not opened within 5 seconds, the relay restores to its locked state.

Note: A Zone 3 Request to Exit is inhibited for 3 seconds after the keypad reads a card

and a door strike occurs. This is to allow entry to the area and pass under a Request-

to-Exit PIR.

Panic Key Options

2-Button Panic Keys

All keypads offer Panic key function that allows

users to send Panic, Emergency, or Fire reports to

the central station. Enable the Panic key function

in the keypad user menu. See Keypad Programming

Instructions later in this document. Install the

supplied icon labels below the top row of Select keys as shown in Figure 4.

The user must press and hold the two Select keys for two seconds until a beep from

the keypad is heard. At the beep, the panel sends the following zone alarm reports to

the central station:

Panic (left two Select keys)—Zone 19 + Device Address

Emergency—non-medical (center two Select keys)—Zone 29 + Device Address

Fire (right two Select keys)—Zone 39 + Device Address

7/0 Panic Keys

All keypads also allow the user to initiate an Panic alarm by pressing the 7 and 0

(zero) keys simultaneously for one-half (1/2) second. Enable the 7/0 Panic function in

Installer Options. See Keypad Programming Instructions later in this document. When

enabled, all keypads send a Zone Short message to the panel for the rst zone of

the keypad address. When the keys are released a Zone Restore message can be sent

from the initiating keypad.

To produce a panic alarm, program the rst zone of the keypad address as a panic

type in panel programming. Place a 1k Ohm end-of-line (EOL) resistor, DMP Model

311, across the White/Brown pair of zone wires on models 7070/7070A, 7073/7073A,

and 7170/7173. This allows a Zone Restore message to be sent when the keys are

released. The 1k Ohm EOL resistor is not required on 7060/7060A, 7063/7063A,

7160/7163 keypads.

Top Row Select Keys

Police Emergency Fire

Label shows Icons only

Figure 4: Label Placement

6 LCD Keypad Installation Guide

Internal Speaker Operation

All keypads emit standard tones for key presses, entry delay, and system alerts. The

speaker also provides distinct burglary, re, zone monitor, and prewarn cadences.

The keypads provide an alternate prewarn with alarm cadence that occurs when the

status list displays a zone alarm.

Backlighting

On Thinline and Aqualite keypads, both the logo and keyboard light when a key is

pressed or the speaker sounds.

On Security Command keypads, only the keyboard lights when a key is pressed or the

speaker sounds. The backlighting dims to medium whenever the speaker is on.

During an alarm condition, all lighted areas turn Red. When all alarm conditions are

cleared from the display, the Red display turns off and the lighted areas return to the

user-selected brightness.

End-User Options

All keypads provide three keypad adjustments the end-user can make through a User

Options Menu. The user can also view the keypad model number and address.

On all keypads press and hold the Back Arrow (<—) and CMD (COMMAND) keys for two

seconds to access User Options. The keypad display changes to SET BRIGHTNESS. Use

the COMMAND key to display the next Option or press the Back Arrow to exit.

Set brightneSS

<        >

Backlighting Brightness

Set the keypad LCD Display brightness level, Power and

Armed LEDs, and the Green keyboard and logo backlighting.

Use the left Select key to lower the brightness and the right

Select key to raise the brightness. If the brightness level is

lowered, it reverts to maximum intensity whenever a key

is pressed. If no keys are pressed, and the speaker has not

sounded for 30 seconds, the user-selected brightness level

restores.

Set tOne

<        >

Internal Speaker Tone

Set the keypad internal speaker tone. At the SET TONE

display, use the left Select key to lower the tone and the

right Select key to raise the tone.

Set VOLUMe LeVeL

<        >

Internal Volume Level

Set the keypad internal speaker volume for key presses

and entry delay tone conditions. During alarm and trouble

conditions, the volume is always at maximum level. Use the

left Select key to decrease the volume and the right Select

key to increase the volume.

MOdeL nUMber

7073 V303 030805

Model Number

The LCD displays the keypad model number and rmware

version and date. The user cannot change this information.

Keypad addreSS

Keypad Address

The LCD displays the current keypad address. The user

cannot change the keypad address.

LCD Keypad Installation Guide 7

Entering Alpha Characters

To enter an alpha character, press the key that has the desired letter written below

it. The keypad display shows the number on that key. To change the number to a

letter, press the top row Select key that corresponds to the letter location under the

key. For example, if you press key number 1, the letters for that key are A, B, and C.

Press the rst Select key for A, the second Select key for B, the third Select key for C,

and the fourth Select key for special characters.

First Letter

Second Letter

Third Letter

Special Character

(CBA

Figure 5: Entering Alpha Characters

Entering Non-Alphanumeric Characters

Each key also has a special, non-alpha character. These characters are not shown on

the keypad. Enter a space by pressing 9 then the third Select key. The following non-

alpha characters are available: ( ) ! ? / & $ ‚ (space) ’ starting with the left bracket

on the 1 digit key to the blank space and apostrophe on the 9 digit key. Use the 0

digit key to enter - . * # (dash, period, asterisk, or number sign). See Figure 6.

1 2 3 4

9 0 CMD

5 6 7 8

(

)

(space)

Figure 6: Keys with Non-Alpha Characters

Installer Options Menu

All keypads provide Keypad Option and Keypad Diagnostic menus to allow installing

and service technicians to congure and test keypad operation.

Accessing Installer Options

Access the Installer Options Menu through the User Options function. Hold down the

Back Arrow and COMMAND keys for two seconds to display SET BRIGHTNESS. Enter

the code 3577 (INST) and press COMMAND. The display changes to KPD OPT (keypad

options) KPD DIAG (keypad diagnostics) and STOP.

The Keypad Options menu allows you to set the keypad address, select Supervised

or Unsupervised mode, change the default keypad message, selectively enable the

2-button Panic keys, Bypass, Request-to-Exit, and set entry card options.

Note: All programming options display on all keypads, however, actual operation for

some programming options is restricted to the listed keypads.

8 LCD Keypad Installation Guide

Programming Keypad Options

Kpd Kpd

Opt diag StOp

Keypad Options (KPD OPT)

To program keypad options, press the left Select key under

KPD OPT.

CUrrent Keypad

addreSS: 01

Keypad Address

Set the keypad address from 01 to 08 with the XT30, XT50,

XR100 or XR150 and 01 to 16 with the XR500 Series or

XR350/XR550 Series. The factory default address is set at

01. To change the current address, press any Select key and

enter the new address. It is not necessary to enter a leading

zero for addresses 01 to 09.

Keypad MOde:

*SUp UnSUp

Keypad Mode

Congure the keypad for either Supervised or Unsupervised

operation. Keypads with zones connected to them must be

supervised and cannot share addresses with other keypads.

Unsupervised keypads can operate with other unsupervised

keypads sharing the same address. Zones cannot be used on

unsupervised keypads. To change the current setting, press

the Select key under SUP or UNSUP. An asterisk appears next

to the selected option.

Note: Unsupervised addresses cannot be used when Device

Fail Output has a programmed value other than zero.

deFaULt Keypad

MSg:

Default Keypad Message

Enter a custom message of up to 16 characters to appear on

the keypad display top line whenever that line is not used for

any other purpose. Press any Select key to clear the current

message and enter a new custom display.

arM paniC KeyS:

*pn *eM *Fi

Arm Panic Keys

Use this option to congure the top row Select keys as

2-button Panic keys. To enable or disable a Panic, press the

Select key under the appropriate display: PN (Panic), EM

(Emergency), and FI (Fire). Once the panic is enabled, an

asterisk displays next to the description. Refer to the Panic

Key Options section earlier in this document.

7/0 paniC

enabLe: nO yeS

7/0 Panic

Select YES to congure the 7 and 0 keys as a 2-button Panic

keys. To disable the option, select NO. Default is NO. Refer

to the Panic Key Options section earlier in this document.

aCtiVate zOne 2

bypaSS: nO yeS

Zone 2 Bypass (7073/7073A/7173 only)

Select YES to enable the Bypass option on zone 2 as

described earlier in this document. This zone provides the

Bypass for door contacts. This zone must be programmed

into the panel.

Autres manuels pour Thinline 7060

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DMP Electronics Clavier

DMP Electronics

DMP Electronics 7800 Series Guide d'installation

DMP Electronics

DMP Electronics 7800 Series Guide d'installation

DMP Electronics

DMP Electronics Security Command 670 Manuel utilisateur

DMP Electronics

DMP Electronics Thinline Aqualite 7000 Series Guide d'installation

DMP Electronics

DMP Electronics SC Series Instructions de montage

DMP Electronics

DMP Electronics 7872 Manuel utilisateur

DMP Electronics

DMP Electronics Aqualite 7560A Manuel utilisateur

DMP Electronics

DMP Electronics Easy Entry 693 Instructions de montage

DMP Electronics

DMP Electronics 9000 Series Guide d'installation

DMP Electronics

DMP Electronics Thinline Series Guide d'installation

DMP Electronics

DMP Electronics Thinline 7160 Manuel utilisateur

DMP Electronics

DMP Electronics 9000 Series Manuel utilisateur

DMP Electronics

DMP Electronics 9000 Series Guide d'installation

DMP Electronics

DMP Electronics XTL Series Manuel utilisateur

DMP Electronics

DMP Electronics 699 Manuel utilisateur

DMP Electronics

DMP Electronics 9000 Series Manuel utilisateur

DMP Electronics

DMP Electronics 532XR Manuel utilisateur

DMP Electronics

DMP Electronics 9800 Series Guide d'installation

DMP Electronics

DMP Electronics 7800 Series Guide d'installation

DMP Electronics

DMP Electronics 7760 Manuel utilisateur

DMP Electronics

DMP Electronics 9800INT Series Guide d'installation

DMP Electronics

DMP Electronics 7000INT Series Guide d'installation

DMP Electronics

DMP Electronics Thinline Series Guide d'installation

DMP Electronics

DMP Electronics 9800 Series Manuel utilisateur

Manuels Clavier populaires d'autres marques

BFT

BFT SELETTO Manuel utilisateur

Micro Id

Micro Id MP7G3BL Manuel d'instructions

WindowMaster

WindowMaster WLI 130 Manuel utilisateur

ACT

ACT ACT PRO 1030 Manuel utilisateur

Cardin

Cardin SSB Series Manuel utilisateur

Harman Kardon

Harman Kardon KP 1 Manuel utilisateur

Chamberlain

Chamberlain KPR2000 Guide de l'utilisateur

CYP

CYP CR-KP1 Manuel utilisateur

Aeware

Aeware k-35 Series Guide de référence

Aritech

Aritech CS-175 Series Manuel utilisateur

GE NetworX NX-1600E Series Manuel utilisateur

Lenze AC Tech

Lenze AC Tech MC SERIES Manuel utilisateur

Burg Wächter

Burg Wächter secuENTRY 7711 Manuel utilisateur

Aeware

Aeware in.k450 Manuel utilisateur

Lenze

Lenze EPM-H410 Manuel utilisateur

Toshiba

Toshiba RKP007Z Manuel utilisateur

Gemini

Gemini GEM-DXK1 KEYPAD Manuel utilisateur

Russound

Russound MDK-C5 Manuel d'utilisation